Digitalinx DL-HD70 Handleiding

Digitalinx Audio/video-converter DL-HD70

Lees hieronder de 📖 handleiding in het Nederlandse voor Digitalinx DL-HD70 (4 pagina's) in de categorie Audio/video-converter. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
DL-HD70 Installation Guide
Included Accessories:
IR Receiver (IR eye) - 2 ea
IR Transmitter (IR emitter) - 2 ea
Power Supply with
locking connector
US Power Cable
3-pole Terminal Block - 2 ea
(attached to the extenders) Mounting brackets with screws - 4 ea
The DigitaLinx DL-HD70 HDBaseT extender set transmits HDMI (1080p, 4Kx2K
(UHD) & 3D) including HDCP 2.2, bidirectional IR, and RS232 up to 70 meters away
using a single Category 6 twisted pair cable.
Built-in surge protection and diagnostic LEDs ensure hassle-free and robust
installations. Flexible power design allows the units to be powered at either the
TX or RX end, and only one power supply is required. The 18 volt power supply is
secured with a screw-on connector to prevent the power from being accidentally
disconnected.
The DL-HD70 is sold only as a set. The individual transmitter and receiver are not
compatible with other HDBaseT devices due to proprietary PoE circuitry.
TIA/EIA-568B
Orange/White
Orange
Green/White
Blue
Blue/White
Green
Brown/White
Brown
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
1 8
Twisted Pair Wiring
Use TIA/EIA-568B wiring for Category
6 connection between send and
receive units.
Tx RXD
GND
Rx TXD
DL-HD70-TX or
DL-HD70-RX
Controller or
Device
RS232 Wiring
Connect the controller or device RXD
signal to Tx on the DL-HD70 extender.
Connect the controller or device TXD
signal to Rx on the DL-HD70 extender.
Diagnostic LEDs:
The DL-HD70 provides four blue LEDs to indicate the current operating status and to
assist troubleshooting an installation.
Power: Solid, the DL-HD70 extender is receiving power from the power supply or from the
remote extender via Category 6 cabling.
Status: Flashes once per second, the HDBaseT processor is running.
Link: Solid, the two DL-HD70 extenders are communicating via Category 6 cabling.
HDCP: Solid, HDCP signal is present in the HDMI stream. Flashes quickly, no HDCP signal
is present in the HDMI stream.
Mode Switch:
The mode switch is used when updating rmware in the extender. A separate document
will provide usage instructions once a new rmware update is available.
Instructions
1. Verify all components included with the extender set are present before
installation.
2. If the extenders are going to be permanently mounted to a surface, attach
the included mounting brackets with the supplied screws.
3. Turn o power and disconnect the audio/video equipment by following the
manufacturer’s instructions.
4. Connect Category 6 or greater twisted pair cable with RJ45 connectors
between the transmitter (DL-HD70-TX) and the receiver (DL-HD70-RX). TIA/
EIA-568B straight-through wiring connections must be used with all HDBaseT
extenders.
5. Connect an HDMI cable and any desired control accessories between the
display and the receiver (DL-HD70-RX).
6. Connect an HDMI cable and any desired control accessories between the
source and the transmitter (DL-HD70-TX).
7. Connect the included power supply to the transmitter or receiver and lock
the power supply to the power connector by twisting the locking collar clockwise.
8. Power on attached audio/video devices.
Passing IR Signals:
The DL-HD70 is capable of passing IR signals between 33 and 55 KHz. To
prevent damage to any of the electronics, the extenders should be powered
o while inserting or removing any IR components. Inserting an IR transmitter
into the IR IN port may damage the IR circuit for that extender.
IR OUT: The IR transmitter (IR emitter) must be plugged into the IR OUT port.
IR IN: The IR receiver (IR eye) must be plugged into the IR IN port.
Important notice:
• Do not attempt to disassemble or alter the extender housing. There are
no user-serviceable parts inside the unit. Doing so will void your warranty.
• To minimize the possibility of equipment damage from electrostatic
discharge (ESD), all source and destination equipment must be powered o
during installation.
• Do not connect the extender to a telecommunication outlet wired
to unrelated equipment. Doing so may damage the unit or any connected
equipment. Ensure all connected twisted pair cabling is straight-through
(point-to-point).
• Allow proper ventilation to reduce the risk of thermal failure.

Product specificaties

Merk: Digitalinx
Categorie: Audio/video-converter
Model: DL-HD70

Heb je hulp nodig?

Als je hulp nodig hebt met Digitalinx DL-HD70 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Audio/video-converter Digitalinx

Digitalinx

Digitalinx DL-HD70 Handleiding

9 Juni 2024
Digitalinx

Digitalinx DL-AVX2100-H2 Handleiding

9 Juni 2024
Digitalinx

Digitalinx DL-ILFO-H2 Handleiding

9 Juni 2024

Handleiding Audio/video-converter

Nieuwste handleidingen voor Audio/video-converter

D-Link

D-Link DES-6505 Handleiding

24 December 2024
Smart-AVI

Smart-AVI V2V-C2H-01 Handleiding

21 December 2024
Smart-AVI

Smart-AVI V2V-H2V-01 Handleiding

21 December 2024
Smart-AVI

Smart-AVI V2V-AV2HV Handleiding

21 December 2024
Smart-AVI

Smart-AVI V2V-MAX 3 Handleiding

21 December 2024
Thor

Thor F-M1SDI-3G-TX/RX Handleiding

10 December 2024
Thor

Thor F-M1SDI-TX/RX Handleiding

10 December 2024
Ocean Matrix

Ocean Matrix OMX-HDMI-2-IP Handleiding

10 December 2024
Ocean Matrix

Ocean Matrix OMX-HDMI-2-IP-T Handleiding

10 December 2024
Decimator

Decimator DMON-4S Handleiding

10 December 2024