Digi XBee-PRO PKG Handleiding

Digi Niet gecategoriseerd XBee-PRO PKG

Lees hieronder de 📖 handleiding in het Nederlandse voor Digi XBee-PRO PKG (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Getting Guide Started 

Connect the Hardware

Connect the hardware as shown in the following images:

Note: To run a successful range test, the remote end must be an RS-232 device.

Set Up Range Test

Install X-CTU Software

X-CTU is a stand-alone tool for configuring XBee devices. It is also used to run a range test and

is included on the Hardware and Software Setup CD. X-CTU can also be found on the website

at: http://www.digi.com/xctu

To install X-CTU:

1. Insert the Hardware and Software Setup CD in the PC’s CD/DVD drive.

2. . On the Home page, click Gateway, Host, Enterprise Documentation/Software

3. . Click X-CTU

4. Click Install X-CTU.

5. When installation completes, start X-CTU by double-clicking on the X-CTU icon placed on

your desktop or by selecting: Start > Programs > Digi > X-CTU

The X-CTU software is ready to be used.

XBee-PRO® 802.15.4 PKG-R &

PKG-U RF Modems

Install USB Drivers (For the XBee-PRO USB PKG version only)

The XBee-PRO USB PKG is a “plug-and-play” device that should be detected by the PC

automatically. To interface between the modem and a PC, two drivers must be installed: a USB

driver and a virtual COM port driver that makes the USB port look and perform like a physical

COM port. After the modem is detected, a wizard for installing the USB driver is launched. The

USB driver is included on the Hardware and Software Setup CD.

To install the two USB drivers:

1. Connect the XBee-PRO USB PKG to a PC using a USB cable. The New Hardware Wizard

dialog box will load.

2. Verify that the Hardware and Software Setup CD is inserted into the CD/DVD drive.

3. . Select Install from a specific list or location (Advanced); then click Next

4. Select Search for the best driver in these locations and search removable media (CD-

ROM). Click Next. A Hardware Installation Windows Logo Testing alert box is displayed.

5. . Click Continue Anyway

6. . Click Finish

You will be prompted to install another driver, the virtual COM port driver. Repeat steps 3

through 6 to install this driver.

Perform Range Test

1. Launch the X-CTU Software: Start > Programs > Digi > X-CTU

2. Under the PC Settings tab, select the PC serial COM port that will be used. The standard

COM port for the 9-pin serial port is COM 1. The USB ports will be labeled as Digi PKG-U

Serial Port Adapters and are assigned a number based on your PC's settings.

3. Verify that the baud rate and data settings match the internal settings of the radios. The

default settings for the radios are Baud Rate: 9600, Flow Control: HARDWARE, Data Bits:

8, Parity: NONE, and Stop Bits: 1.

4. Select the Range Test tab.

5. (Optional) Check the RSSI checkbox to enable the Received Signal Strength Indicator. The

RSSI value indicates the signal strength of the last packet that the radio received.

6. Click Start to begin the range test.

7. Monitor the link quality by reading the Percent section on the Range Test tab. This section

displays the running percentage of good packets sent to the receiving radio and looped back

to the base.

8. Click Stop to end the range test.

Toll-free phone U.S.A. & Canada: (866) 765-9885

Worldwide: (801) 765-9885

Online support: http://www.digi.com/support/eservice/login.jsp

Product specificaties

Merk:	Digi
Categorie:	Niet gecategoriseerd
Model:	XBee-PRO PKG
Gewicht:	150 g
Certificering:	FCC, IC, EC
Interface:	RS-232
Ingangsspanning:	5 - 14 V
Modulatie:	OQPSK
Gevoeligheid ontvanger:	-100 dBm
Impedantie:	50 Ohm
Frequentie:	2400 MHz
Aansluiting antenne:	RP-SMA
Afmetingen (B x D x H):	114 x 70 x 29 mm
Bedrijfstemperatuur (T-T):	-40 - 85 °C
Connectivity LEDs:	Ja
Spread spectrum methode:	DSSS
Netwerktopologie:	IEEE 802.15.4
Ontvang stroom:	80 mA
Transmit stroom:	300 mA
Kracht beneden stroom:	6 mA
Data doorvoersnelheid:	9.6 Kbit/s
Ondersteunde netwerk topologies:	Peer-to-peer, Point-to-multipoint, Point-to-point