Digi Connect SP and Wi-SP Handleiding

Digi Niet gecategoriseerd Connect SP and Wi-SP

Lees hieronder de 📖 handleiding in het Nederlandse voor Digi Connect SP and Wi-SP (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick Start

Guide

Digi Connect® SP and Wi-SP

1Verify your components

Verify that you have all included equipment. If any item is missing or damaged, contact your supplier.

Included equipment

Required additional equipment

2Connect the hardware

Digi Connect SP: Digi Connect Wi-SP:

Connect the power supply to the power connector.

Connect the Ethernet cable to the Ethernet port.

Connect the power supply to the power connector.

Connect the Wi-Fi antenna to the antenna connector.

3Download the required software and documentation

1. Navigate to www.digi.com/products/serial-servers/wireless-serial-servers/digiconnectwisp, and click the link under theUtilities Product Support tab.

2. Select your operating system. A list of available utilities for your operating system appears.

3. Download and run either the Device Discovery Utility Digi Port Authority - Remoteor .

If the serial ports for your product will be managed using Digi’s RealPort software, download the RealPort driver.

1. Navigate to www.digi.com/products/serial-servers/wireless-serial-servers/digiconnectwisp, and select Drivers under the Product Support tab.

2. Select your operating system. A list of available downloads and release notes for your operating system appears.

3. Download the RealPort driver and the release notes.

Note For Microsoft Windows operating systems, unzip the download package and run the executable. For Linux or UNIX operating systems, follow the instructions in the

release notes.

For additional support, download product support documentation.

1. Navigate to www.digi.com/products/serial-servers/wireless-serial-servers/digiconnectwisp.

2. Click the Product Support tab.

3. Navigate to the product documentation and other available resources as needed.

4Connect to the network

Note This section requires serial terminal software, such as Hyperterm or PuTTY. Download one of these programs if you do not have one installed.

Configure Digi Connect SP

Use the Digi Discovery Utility Digi Port Authority - Remoteor to discover devices on your network and open the web interface.

1. In the list of discovered devices, select the Digi Connect SP device.

2. Using the Digi Discovery Utility or Digi Port Authority, configure the IP address if necessary.

3. Open the Digi Connect SP web interface. In the Device Discovery Utility, click Open web interface. In Digi Port Authority-Remote, click Device Configuration.

4. A login prompt for the web interface appears. Enter the default username and password: root dbpsand . Continue to section 5.

Configure Digi Connect Wi-SP

There are two methods to configure the network connection on a Digi Connect Wi-SP. Use the method you prefer.

Method 1: Use an access point preconfigured with the default SSID of CONNECT with no encryption and let the Digi Connect Wi-SP associate to it.

1. Once the device has associated, use the Digi Discovery Utility Digi Port Authority - Remoteor to discover devices on your network and open the web interface.

2. In the list of discovered devices, select the Digi Connect Wi-SP device.

3. Using the Digi Discovery Utility or Digi Port Authority, configure the IP address if necessary.

4. Open the Digi Connect Wi-SP web interface. In the Device Discovery Utility, click Open web interface. In Digi Port Authority-Remote, click Device Configuration.

5. A login prompt for the web interface appears. Enter the default username and password: root dbpsand . Continue to section 5.

Digi, Digi International, and the Digi logo are trademarks or registered trademarks in the United States and other countries worldwide. All other trademarks mentioned in this document are the

property of their respective owners.

6. From the web interface, you can then set a new SSID to match the intended production network’s SSID and security options.

7. Click . The device will join that network on the next reboot.Apply

Method 2: Configure the Digi Connect Wi-SP through the serial port.

This method requires a DB-9 null-modem cable and a serial terminal application on your computer, such as Hyperterm or PuTTY.

1. On the Digi Connect Wi-SP, set all four DIP switches to the up position.

2. Configure your serial terminal software to use the following serial settings:

baud rate = 9600 data bits = 8 stop bits = 1 parity = none flow control = none

3. Connect the null modem cable to the computer and the Digi Connect Wi-SP serial port.

4. A login prompt for the device appears. Enter the default username and password: root dbpsand .

5. Enter the command to set the Wi-Fi interface parameters. For example:set wlan

#>set wlan channel=11 ssid=testssid authentication=wpa_psk encryption=ccmp psk=1234567890

Note For a detailed description of the command, see theset wlan Digi Connect Family Command Reference. For a video guide to serial port configuration, see

www.digi.com/videos/digi-connect-wi-sp-serial-port-configuration.

The device connects to the Wi-Fi network. You can further configure the device through the web interface. Use the Digi Discovery Utility or Digi Port Authority - Remote to

discover devices on your network and open the web interface.

1. In the list of discovered devices, select the Digi Connect Wi-SP device.

2. Configure the IP address if necessary.

3. Open the Digi Connect Wi-SP web interface. In the Device Discovery Utility, click . In Digi Port Authority-Remote, clickOpen web interface Device Configuration.

4. A login prompt for the web interface appears. Enter the default username and password: root dbpsand .

Your Digi Connect SP/Wi-SP device is now connected to the network and configured for basic network connectivity. Go to sections 5 and 6 to configure the serial port as

needed.

5Configure DIP switches

Digi Connect SP and Digi Connect Wi-SP have a set of DIP switches on the underside of the device for setting the EIA mode for serial communications. Set these DIP switches

according to your serial device requirements (EIA-232/422/485). See the table for the device server pinouts.

Up/On

Down/Up

DB-9 pin EIA-232 EIA-422/485 Full-duplex EIA-485 Half-duplex

1 DCD CTS- Not used

2 RxD RxD+ RxD+

3 TxD TxD+ TxD+

4 DTR RTS- Not used

5 GND GND GND

6 DSR RxD- RxD-

7 RTS RTS+ Not used

8 CTS CTS+ Not used

9 RI TxD- TxD-

Shell GND

Note If switch 4 is up, the termination resistor is connected. If the switch is down, the termination resistor is not connected.

6Connect the serial end device

1. Connect the serial end device to the serial port.

2. In the web interface, under Configuration, click Serial Ports. Configure serial port settings using port profiles. Port profiles are a

defined set of serial port parameters for a particular use. The web interface and user guide contain descriptions of the port

profiles. For Digi Connect SP/Wi-SP products, Digi recommends the RealPort profile. For help in configuring the device for use with

other port profiles, see the Digi Connect Family and ConnectPort TS Family User Guide.

To configure ports to use the RealPort profile:

a. On the Serial Port Configuration page, click the port to be configured.

b. Click Change Profile.

c. In the list of profiles, select the RealPort profile.

d. Click .Apply

For additional cabling information, go to www.digi.com/products/serial-servers/wireless-serial-servers/digiconnectwisp and click the Cabling link under the Product

Support tab.

7Next steps

Digi Technical Support: Digi offers multiple technical support plans and service packages to help our customers get the most out of their Digi product. For information on