DeWalt DWD460 Handleiding

DeWalt Boormachine DWD460

Lees hieronder de 📖 handleiding in het Nederlandse voor DeWalt DWD460 (7 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

DWD450, DWD460

VSR Stud and Joist Drill

Perceuse pour charpente VSR

Taladro RVS (Rango de Velocidad Variable) para Vigas

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, result will

in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: may Indicates a potentially hazardous situation which, if not avoided, result

in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation

which, if not avoided, result in may property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault

circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or

a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could result

in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Additional Specific Safety Instructions

• Wear ear protectors with impact drills. Exposure to noise can cause hearing loss.

• Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tools may contact hidden wiring or its own cord. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

• Wear safety goggles or other eye protection. Hammering and drilling operations cause

chips to fly. Flying particles can cause permanent eye damage.

• Keep handles dry, clean, and free from oil and grease. This will enable better control of

the tool.

• Air vents often cover moving parts and should be avoided. Loose clothes, jewellery or

long hair can be caught in moving parts.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that

is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating. When using more than one extension to

make up the total length, be sure each individual extension contains at least the minimum

wire size. The following table shows the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge

number, the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than

AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.

Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY

EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V ......................volts A ................amperes

Hz ....................hertz W ...............watts

min ..................minutes .............alternating current

...............direct current .............alternating or direct current

....................Class I Construction no ..............no load speed

........................(grounded) ...............earthing terminal

....................Class II Construction ..............safety alert symbol

........................(double insulated) BPM...........beats per minute

…/min .............per minute RPM ..........revolutions per minute

SAVE THESE INSTRUCTIONS FOR FUTURE USE

COMPONENTS (Fig. 1)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could

result.

A. Bail handle

B. Speed selector lever

C. Forward/reverse button

D. Trigger switch

E. Bail handle bolt

F. 1/2" (13 mm) keyed chuck

G. Bind up control indicator (DWD460)

H. Knuckle guard (DWD460)

I. Side handle (two positions)

INTENDED USE

The DWD450 and DWD460 heavy-duty stud and joist drills are designed for professional drilling

at various work sites (i.e., construction sites). DO NOT use under wet conditions or in presence

of flammable liquids or gases.

These heavy-duty stud and joist drills are professional power tools. DO NOT let children come

into contact with the tool. Supervision is required when inexperienced operators use this tool.

Motor

Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than

10% will cause loss of power and overheating. DEWALT tools are factory tested; if this tool

does not operate, check power supply.

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme;

the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the

array of lozenge-shaped humps on the surface of the tool.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D WALT • www.dewalt.comE

Torque

WARNING: This is a high-torque drill. To reduce the risk of serious personal injury, ALWAYS

hold tool firmly with both hands in the proper position for operation as shown.

Torque is the twisting action the drill produces in regards to the rotating bit. As the drill bit meets

resistance in the material being drilled, the motor responds by adjusting the output torque to

meet the requirement up to the maximum capacity of the motor and gear system.

BRACING THE TOOL (FIG. 2, 10)

WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position

as shown in Figure 2.

WARNING: To reduce the risk of serious personal injury, ALWAYS hold or brace the tool

securely in anticipation of a sudden reaction.

With hands in the proper hand position, brace the tool as shown in Figure 10.

SLIP CLUTCH

The DWD450 and DWD460 are each equipped with a slip clutch. The clutch is active when the

low speed (1) is selected. When the bit or cutter bites into the workpiece, the clutch will slip and

a ratcheting sound will be heard. Release the trigger. Continued clutching of the tool will reduce

the life of this feature.

BIND-UP CONTROL (DWD460)

The DWD460 is equipped with bind-up control. This feature senses the motion of tool and

reduces the motor torque to a manageable level if necessary. The bind-up control indicator (G)

will illuminate to indicate status.

INDICATOR DIAGNOSIS SOLUTION

OFF Tool is functioning normal Follow all warnings and instructions

when operating tool

SOLID Bind up control has been activated

With tool properly supported, release

trigger; The tool will function normally

when the trigger is depressed again

and the indicator light will go out

FLASHING Bind up control is malfunctioning Take the tool to an authorized

DEWALT repair agent.

NOTE: If tool power is insufficient for normal drilling and LED does not flash take tool to autho-

rized DEWALT repair center.

Bail Handle (Fig. 1, 3)

A bail handle is provided for carrying the tool and for use as an additional handle. Assemble the

bail handle in one of the positions shown in Figure 3. When changing the location of the bail

handle from one position to the other, completely remove the two bail handle bolts (E) securing

it. Flip the handle over and reinstall.

Side Handle (Fig. 4)

WARNING: To reduce the risk of personal injury, always operate the tool with the side handle

properly installed and tightened. Failure to do so may result in the side handle slipping during

tool operation and subsequent loss of control. Hold tool with both hands to maximize control.

The two position side handle (I) can be assembled into either side of tool. Thread the side handle

(I) into the bail handle bolt (E) or directly into threaded holes (J) on desired side. Tighten securely

by hand.

Speed Selector (Fig. 1)

CAUTION: Risk of tool damage. Do not rotate the speed selector lever while the drill is running

or coasting, damage may occur to the tool.

Rotate the speed selector lever (B) to the desired speed:

1 = low speed (330 RPM)

2 = high speed (1300 RPM)

NOTE: The first time the tool is run after changing speeds, you may hear a click on start up. This

is normal and does not indicate a problem.

Trigger Switch

Depressing the trigger switch (D) turns the tool on, releasing the trigger switch turns the tool off.

VARIABLE SPEED

A variable speed trigger switch permits speed control—the farther the trigger is depressed, the

higher the speed of the drill.

NOTE: Use lower speeds for starting holes without a center punch, drilling in metal, plastics or

ceramics. Higher speeds are better for drilling wood and composition boards.

Forward/Reverse Button (Fig. 1)

A forward/reverse button (C) determines the direction of the tool. It is located in front of the

trigger switch.

To select forward rotation, release the trigger switch (D) and depress the forward/reverse

button on the right side of the tool.

To select reverse, depress the forward/reverse button on the left side of the tool. When

changing the position of the button, be sure the trigger is released.

NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click

on start up. This is normal and does not indicate a problem.

OPERATION

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect

tool from power source before making any adjustments or removing/installing attachments

or accessories.

The bit rotates clockwise when the tool is in the forward position and counterclockwise when

the tool is in the reverse position. If the bit binds, the tool will slow to a manageable level. Using

proper hand position, brace the side handle (I) or tool body against a stud for better support.

Drilling

WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is anchored

or clamped firmly. If drilling thin material, use a wood “back-up” block to prevent damage to the

material.

1. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or hole

saws. For METAL, use steel twist drill bits or hole saws.

2. Always apply pressure in a straight line with the bit. Use enough pressure to keep drill biting,

but do not push hard enough to stall the motor or deflect the bit.

3. Hold tool firmly with both hands to control the twisting action of the drill.

4. IF DRILL STALLS, it is usually because it is being overloaded or improperly used. RELEASE

TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO

NOT CLICK TRIGGER ON AND OFF IN AN ATTEMPT TO START A STALLED DRILL —

THIS CAN DAMAGE THE DRILL.

5. To minimize stalling or breaking through the material, reduce pressure on drill and ease the

bit through the last fractional part of the hole.

6. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent

jamming.

7. With variable speed drills there is no need to center punch the point to be drilled. Use a

slow speed to start the hole and accelerate by squeezing the trigger harder when the hole

is deep enough to drill without the bit skipping out.

DRILLING IN METAL

Start drilling with slow speed and increase to full power while applying firm pressure on the

tool. A smooth even flow of metal chips indicates the proper drilling rate. Use a cutting lubricant

when drilling metals. The exceptions are cast iron and brass which should be drilled dry.

NOTE: Large [5/16" (8 mm) to 1/2" (13 mm)] holes in steel can be made easier if a pilot hole

[5/32" (4 mm) to 3/16" (5 mm)] is drilled first.

DRILLING IN WOOD

Start drilling with slow speed and increase to full power while applying firm pressure on the tool.

Holes in wood can be made with the same twist drills used for metal. These bits may overheat

unless pulled out frequently to clear chips from the flutes. Work that is apt to splinter should be

backed up with a block of wood.

Chuck Key Holder (Fig. 5, 6, 7)

1. Push double-hole end of holder through the slot in other end of holder (Fig. 5).

2. Slip loop over electric plug and draw loop tight around cord (Fig. 6).

3. Push ends of chuck key handle (long end first) through two holes in end of holder (Fig. 7).

Keyed Chuck

Open the chuck jaws by turning collar by hand and insert the shank of the bit about

3/4" (19 mm)

into chuck. Tighten the chuck collar by hand. Place chuck key in each of the three holes, and tighten

in clockwise direction. It’s important to tighten chuck with all three holes. To release the bit, turn the

chuck counterclockwise in just one hole, then loosen the chuck by hand.

NOTE:

When using hex shank or three sided shank bits be sure to align the flat sides of the bit with

the chuck jaws to ensure the bit is properly engaged by the jaws.

REMOVAL OF KEYED CHUCK (FIG. 8)

Remove the left-handed clutch screw using a T25 torx wrench, rotating clockwise to loosen.

Tighten the chuck around the shorter end of a hex wrench (not supplied) of 3/8" (10 mm) size.

FIG. 3

FIG. 5 FIG. 6 FIG. 7

DWD450

DWD460

FIG. 1

FIG. 2

FIG. 9

FIG. 8

FIG. 10

FORWARD

AVANT

AVANCE

REVERSE

ARRIÈRE

REVERSO

FIG. 4

With the tool braced securely, use a soft hammer and strike the hex wrench sharply in the

counterclockwise direction when viewed from the front of the tool. This will loosen the chuck

that it can be removed by hand.

KEYED CHUCK INSTALLATION (FIG. 9)

Screw the chuck on by hand as far as it will go. Insert the shorter end of a hex wrench (not

supplied) of 3/8" (10 mm) size and strike it in the clockwise direction with a soft hammer.

Reinstall the left handed clutch screw.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect

tool from power source before making any adjustments or removing/installing attachments

or accessories.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.

To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when

performing this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts

of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse

any part of the tool into a liquid.

Motor Brushes

DEWALT uses an advanced brush system which automatically stops the drill when the brushes

wear out. This prevents serious damage to the motor. New brush assemblies are available at

authorized DEWALT service centers. Always use identical replacement parts.

Lubrication

Your tool was properly lubricated before leaving the factory. In from two to six months,

depending upon use, take or send your tool to a DEWALT Service Center or other qualified

service organization for a complete cleaning, inspection and relubrication.

Tools used constantly on production or heavy duty jobs or exposed to heat may require more

frequent lubrication. Tools “out of service” for long periods should be relubricated before being

put back into service.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments (including

brush inspection and replacement) should be performed by a DEWALT factory service center,

a DEWALT authorized service center or other qualified service personnel. Always use identical

replacement parts.

Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been tested

with this product, use of such accessories with this tool could be hazardous. To reduce the risk

of injury, only DEWALT, recommended accessories should be used with this product.

Recommended accessories for use with your tool are available at extra cost from your local

service center.

If you need assistance in locating any accessory, please contact DEWALT Industrial Tool Co.,

701 East Joppa Road, Baltimore, MD 21286 or call 1-800-4-DEWALT (1-800-433-9258).

CAUTION: To reduce the risk of injury, the following accessories should be used only in sizes

up to the maximums shown in the table below.

MAXIMUM RECOMMENDED CAPACITIES

LOW SPEED HIGH SPEED

R.P.M. 330 1300

WOOD, FLAT BORING – 1-1/2" (38 mm)

HOLE SAWS 6" (152.4 mm)

SHIP AUGER – 1-1/2" (38 mm)

SELF-FEED BITS 4-5/8" (102 mm) 2-9/16" (65 mm)

CLUTCH OPERATIVE YES NO

BIND UP CONTROL (DWD460) YES YES

NOTE: For holes in metal larger than 1/2" (13 mm) use hole saws.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for

three years from the date of purchase. This warranty does not cover part failure due to normal

wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit

www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to

accessories or damage caused where repairs have been made or attempted by others. This

warranty gives you specific legal rights and you may have other rights which vary in certain

states or provinces.

In addition to the warranty, DEWALT tools are covered by our:

1 YEAR FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or

Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt

for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products

sold in Latin America, see country specific warranty information contained either in the

packaging, call the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are

missing, call 1-800-4-DEWALT for a free replacement.

Définitions : lignes directrices en matière de

sécurité

Les définitions ci-dessous décrivent le niveau de danger pour chaque mot-indica-

teur employé. Veuillez lire le mode d’emploi et porter une attention particulière à ces

symboles.

DANGER : indique une situation dangereuse imminente qui, si elle n’est pas

évitée, causera la mort ou des blessures graves.

AVERTISSEMENT : indique une situation potentiellement dangereuse qui, si elle

n’est pas évitée, se solder par unpourrait décès ou des blessures graves.

ATTENTION : indique une situation potentiellement dangereuse

qui, si elle n’est pas évitée se solder par pourrait des blessures mineures ou

modérées.

ATTENTION : utilisé sans le symbole d’alerte à la sécurité, indique une situation

potentiellement dangereuse qui, si elle n’est pas évitée se solder par pourrait des

dommages à la propriété.

POUR TOUT COMMENTAIRE OU QUESTION RELATIF À CET OUTIL OU TOUT AUTRE

OUTIL DEWALT, COMPOSEZ GRATUITEMENT LE : 1-800-4-DEWALT (1-800-433-9258).

AVERTISSEMENT : Pour réduire tout risque de dommage corporel, lire le manuel de

l’utilisateur.

Directives de sécurité relatives aux outils électriques

en général

AVERTISSEMENT ! Lire toutes les directives et consignes de sécurité. Tout

manquement aux directives et consignes pose des risques de choc électrique, d’incendie

et/ou de blessure grave.

CONSERVER TOUTES CES DIRECTIVES

ET CONSIGNES À TITRE DE RÉFÉRENCE

Le terme « outil électrique » dans ces directives se rapporte à votre outil électrique alimenté sur

secteur (avec fil) ou par piles (sans fil).

1) SÉCURITÉ - AIRE DE TRAVAIL

a) Maintenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont

propices aux accidents.

b) Ne pas faire fonctionner un outil électrique dans une atmosphère explosive, en

présence par exemple de poussières, gaz ou liquides inflammables. Les outils

électriques peuvent produire des étincelles qui pourraient enflammer toute émanation ou

poussière ambiante.

c) Tenir les enfants, ou toute autre personne, à l’écart pendant l’utilisation d’un outil

électrique. Toute distraction pourrait faire perdre la maîtrise de l’appareil.

2) SÉCURITÉ – ÉLECTRICITÉ

a) La fiche électrique de l’outil doit correspondre à la prise murale. Ne jamais modifier

la fiche en aucune façon. Ne jamais utiliser de fiche d’adaptation avec un outil

électrique mis à la terre. L’utilisation de fiches d’origine et de prises appropriées réduira

les risques de choc électrique.

b) Éviter tout contact corporel avec des éléments mis à la terre comme tuyaux,

radiateurs, cuisinières ou réfrigérateurs. Les risques de choc électrique augmentent

lorsque le corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. Toute pénétration d’un

outil électrique par un liquide augmente les risques de choc électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour

transporter, tirer ou débrancher un outil électrique. Protéger le cordon de la chaleur,

de l’huile et de tout bord tranchant ou pièce mobile. Les cordons endommagés ou

emmêlés augmentent les risques de choc électrique.

e) Lors de l’utilisation d’un outil électrique à l’extérieur, n’utiliser que des rallonges

conçues pour l’extérieur. L’utilisation d’une rallonge conçue pour l’extérieur réduit les

risques de choc électrique.

f) Si l’utilisation d’un outil électrique en milieu humide est inévitable, utiliser une

alimentation protégée par un disjoncteur de fuites à la terre (DDFT). L’utilisation d’un

DDFT réduit les risques de choc électrique.

3) SÉCURITÉ PERSONNELLE

a) Rester constamment vigilant et faire preuve de jugement pendant l’utilisation

d’un outil électrique. Ne pas utiliser d’outil électrique en cas de fatigue ou sous

l’influence de drogues, d’alcool ou de médicaments. Tout moment d’inattention

pendant l’utilisation d’un outil électrique pose des risques de blessure grave.

b) Utiliser un équipement de protection individuel. Porter systématiquement des

lunettes de protection. Le fait de porter un équipement de protection tel que masque

antipoussières, chaussures antidérapantes, casque de sécurité ou protecteurs auditifs

lorsque la situation le requiert, réduira les risques de dommages corporels.

c) Prévenir tout démarrage accidentel. S’assurer que l’interrupteur est en position

d’arrêt avant de brancher l’outil et/ou de le connecter à un bloc-piles, et avant de le

saisir ou de le transporter. Transporter un outil le doigt sur l’interrupteur, ou brancher un

outil électrique alors que l’interrupteur est en position de marche, invite les accidents.

d) Retirer toute clé de réglage avant de démarrer l’outil. Une clé laissée sur une pièce

rotative d’un outil électrique pose des risques de blessure.

e) Ne pas effectuer de travaux hors de portée. Les pieds doivent rester bien ancrés

au sol afin de maintenir son équilibre en tout temps. Cela permet de mieux maîtriser

l’outil électrique dans les situations imprévues.

f) Porter des vêtements appropriés. Ne pas porter de vêtements amples ni de bijoux.

Maintenir cheveux, vêtements et gants éloignés des pièces mobiles. Vêtements

amples, bijoux ou cheveux longs risquent de rester coincés dans ces pièces mobiles.

g) Lorsqu’un dispositif de connexion à un système de dépoussiérage ou d’élimination

est fourni, s’assurer qu’il est connecté et utilisé correctement. L’utilisation d’aspirateurs

peut réduire les risques engendrés par les poussières.

4) UTILISATION ET ENTRETIEN DES OUTILS ÉLECTRIQUES

a) Ne pas forcer un outil électrique. Utiliser l’outil approprié au travail en cours. L’outil

approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse pour laquelle il

a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout appareil

dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche du secteur et/ou le bloc-piles de l’outil électrique avant de

faire tout réglage ou changement d’accessoire, ou avant de ranger ce dernier. Ces

mesures préventives réduisent les risques de démarrage accidentel de l’appareil.

d) Après usage, ranger les outils électriques hors de la portée des enfants, et ne

permettre à aucune personne n’étant pas familière avec un outil électrique (ou son

manuel d’instruction) d’utiliser ce dernier. Les outils peuvent être dangereux entre les

mains des novices.

e) Entretenir les outils électriques. Vérifier les pièces mobiles pour s’assurer qu’elles

sont bien alignées et tournent librement, qu’elles sont en bon état et ne sont

affectées d’aucune condition susceptible de nuire au bon fonctionnement de l’outil.

En cas de dommage, faire réparer l’outil électrique avant toute nouvelle utilisation.

Bien des accidents sont causés par des outils mal entretenus.

f) Maintenir toute lame aiguisée et propre. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus faciles à contrôler.

g) Utiliser un outil électrique, ses accessoires, mèches, etc., conformément aux

présentes directives en tenant compte des conditions de travail et du travail à

effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour

laquelle il a été conçu est dangereuse.

5) SERVICE

a) Faire entretenir les outils électriques par un réparateur qualifié en utilisant

seulement des pièces de rechange identiques. Cela permettra d’assurer l’intégrité de

l’outil électrique et la sécurité de l’utilisateur.

Consignes de sécurité particulières additionnelles

• Pendant l’utilisation d’une perceuse à percussion, porter un protège-oreille. Le bruit en

résultant pourrait occasionner une perte de l’ouïe.

• Utiliser les poignées auxiliaires fournies avec l’outil. Une perte de contrôle de l’outil

pourrait occasionner des dommages corporels.

• Tenir l’outil par les surfaces isolées prévues à cet effet pendant toute utilisation où

l’organe de coupe pourrait entrer en contact avec des fils électriques cachés ou son

propre cordon. Tout contact avec un fil sous tension met les parties métalliques exposées

de l’outil sous tension et électrocute l’utilisateur.

• Utiliser des serre-joints ou tout autre moyen pour fixer et immobiliser le matériau

sur une surface stable. Tenir la pièce à la main ou contre son corps offre une stabilité

insuffisante qui pourrait vous en faire perdre le contrôle.

• Porter des lunettes de protection ou toute autre protection oculaire. Le martelage et

le perçage peuvent faire voltiger des éclats. Ces particules volantes pourraient occasionner

des dommages oculaires permanents.

• Maintenir les poignées propres et sèches, exempts d’huile ou de graisse. Cela

permettra un meilleur contrôle de l’outil.

• Prendre des précautions à proximité des évents, car ils cachent des pièces mobiles.

Vêtements amples, bijoux ou cheveux longs risquent de rester coincés dans ces pièces

mobiles.

• Pour la sécurité de l’utilisateur, utiliser une rallonge de calibre adéquat (AWG,

American Wire Gauge [calibrage américain normalisé des fils électriques]). Plus

le calibre est petit, et plus sa capacité est grande. Un calibre 16, par exemple, a plus de

capacité qu’un calibre 18. L’usage d’une rallonge de calibre insuffisant causera une chute de

tension entraînant perte de puissance et surchauffe. Si plus d’une rallonge est utilisée pour

obtenir une certaine longueur, s’assurer que chaque rallonge présente au moins le calibre

de fil minimum. Le tableau ci-dessous illustre les calibres à utiliser selon la longueur de

rallonge et l’intensité nominale indiquée sur la plaque signalétique. En cas de doute, utiliser

le calibre suivant. Plus le calibre est petit, plus la rallonge peut supporter de courant.

Calibres minimaux des rallonges

Intensité (en ampères)

Volts Longueur totale de cordon en mètres (pieds)

120V 7,6 (25) 15,2 (50) 30,5 (100) 45,7 (150)

240V 15,2 (50) 30,5 (100) 61,0 (200) 91,4 (300)

Supérieur

Inférieur

à AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Non recommandé

AVERTISSEMENT : Porter SYSTÉMATIQUEMENT des lunettes de protection. Les

lunettes courantes NE sont PAS des lunettes de protection. Utiliser aussi un masque

antipoussières si la découpe doit en produire beaucoup. PORTER SYSTÉMATIQUEMENT UN

ÉQUIPEMENT DE PROTECTION HOMOLOGUÉ.

• Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3 ;

• Protection auditive ANSI S12.6 (S3.19) ;

• Protection des voies respiratoires NIOSH/OSHA/MSHA.

AVERTISSEMENT : Certains outils électriques, tels que les sableuses, les scies, les meules,

les perceuses ou autres outils de construction peuvent produire de la poussière contenant des

produits chimiques susceptibles d’entraîner le cancer, des malformations congénitales ou

pouvant être nocifs pour le système reproductif. Parmi ces produits chimiques, on retrouve :

• le plomb dans les peintures à base de plomb ;

• la silice cristallisée dans les briques et le ciment ou autres articles de maçonnerie, et

Product specificaties

Merk:	DeWalt
Categorie:	Boormachine
Model:	DWD460

Heb je hulp nodig?

Als je hulp nodig hebt met DeWalt DWD460 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Boormachine DeWalt

DeWalt DW9106 Handleiding

15 November 2024

DeWalt DCB126 Handleiding

2 November 2024

DeWalt DCH033 Handleiding

11 September 2024

DeWalt DWD216G Handleiding

29 Augustus 2024

DeWalt DCD445 Handleiding

27 Augustus 2024

DeWalt DW235G Handleiding

26 Augustus 2024

DeWalt DC987-XE Handleiding

15 Juli 2024

DeWalt DW922K2 Handleiding

15 Juli 2024

DeWalt DCD932 Handleiding

15 Juli 2024

DeWalt D21717 Handleiding

15 Juli 2024

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine

Milwaukee M12 BDDXKIT Handleiding

16 November 2024

Metabo BS 12 BL Q Handleiding

15 November 2024

Gude GTB 16/12 R+L Handleiding

15 November 2024

MSW -DMS400 Handleiding

4 November 2024

Vonroc CD510DC Handleiding

20 Oktober 2024

MSW -DDM300 Handleiding

16 Oktober 2024

MSW ACC-B1 Handleiding

16 Oktober 2024

MSW -DDM260 Handleiding

16 Oktober 2024

MSW -DDM132 Handleiding

16 Oktober 2024

MSW -DDM230 Handleiding

16 Oktober 2024