DeWalt DC900KL Handleiding

DeWalt Boormachine DC900KL

Lees hieronder de 📖 handleiding in het Nederlandse voor DeWalt DC900KL (7 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. LÉASE ESTE INSTRUCTIVOADVERTENCIA:

ANTES DE USAR EL PRODUCTO.

DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme;

the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the

array of lozenge-shaped humps on the surface of the tool.

DC900

Heavy-Duty 36V Cordless Hammerdrill

Marteau perforateur industriel sans fil de 36 volts

Taladro percutor inalámbrico de 36 V para trabajo pesado

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

General Safety Rules – For All Battery Operated Tools

WARNING! Read all instructions. Failure to follow all instructions listed below

may result in electric shock, fire and/or serious injury. The term “power tool” in all

of the warnings listed below refers to your mains-operated (corded) power tool or bat-

tery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock. Replace or repair damaged cords.

Make sure your extension cord is in good condition. Use only 3-wire extension cords that

have 3-prong grounding-type plugs and 3-pole receptacles that accept the tool’s plug.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock. When using

an extension cord, be sure to use one heavy enough to carry the current your product will

draw. An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size to use depending on cord length

and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage

number, the heavier the cord.

Recommended Minimum Wire Size for Extension Cords

Total Length of Cord

25 ft. 50 ft. 75 ft. 100 ft. 125 ft. 150 ft. 175 ft.

7.6 m 15.2 m 22.9 m 30.5 m 38.1 m 45.7 m 53.3 m

Wire Size AWG

18 18 16 16 14 14 12

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personal injury.

b) Use safety equipment. Always wear eye protection. Safety equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate condi-

tions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off-position before plugging

in. Carrying power tools with your finger on the switch or plugging in power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or

a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in

moving parts. Air vents often cover moving parts and should also be avoided.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of these devices can reduce dust-

related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The cor-

rect power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfa-

miliar with the power tool or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tools operation. If

damaged, have the power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions and in the manner intended for the particular type of power tool, taking

into account the working conditions and the work to be performed. Use of the power

tool for operations different from those intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Ensure the switch is in the off position before inserting battery pack. Inserting the

battery pack into power tools that have the switch on invites accidents.

b) Recharge only with the charger specified by the manufacturer. A charger that is

suitable for one type of battery pack may create a risk of fire when used with another

battery pack.

c) Use power tools only with specifically designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

d) When battery pack is not in use, keep it away from other metal objects like paper

clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another. Shorting the battery terminals together may

cause burns or a fire.

e) Under abusive conditions, liquid may be ejected from the battery, avoid contact. If

contact accidentally occurs, flush with water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Specific Safety Rules for Hammerdrills

•Hold tool by insulated gripping surfaces when performing an operation where the tool

may contact hidden wiring or its own cord. Contact with a “live” wire will also make

exposed metal parts of the tool “live” and shock the operator.

•Wear ear protectors with impact drills. Exposure to noise can cause hearing loss.

•Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.

• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

•Wear ear protectors when hammering for extended periods of time. Prolonged expo-

sure to high intensity noise can cause hearing loss. Temporary hearing loss or serious ear

drum damage may result from high sound levels generated by hammerdrilling.

•Wear safety goggles or other eye protection. Hammering and drilling operations cause

chips to fly. Flying particles can cause permanent eye damage.

•Always use the side handle supplied with the tool. Keep a firm grip on the tool at all times.

Do not attempt to operate this tool without holding it with both hands.

•Hammer bits and tools get hot during operation. Wear gloves when touching them.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.

Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY

EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: When not in use, place tool on its side on a stable surface where it will not

cause a tripping or falling hazard. Some tools with large battery packs will stand upright on

the battery pack but may be easily knocked over.

CAUTION: Wear appropriate hearing protection during use. Under some conditions

and duration of use, noise from this product may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V..................volts A ..................amperes

Hz................hertz W..................watts

min ..............minutes ................alternating current

............direct current no ................no load speed

................Class I Construction ..................earthing terminal

....................(grounded) ..................safety alert symbol

................Class II Construction …/min ..........revolutions or reciprocation

.................... ....................(double insulated) per minute

BPM ............beats per minute

Important Safety Instructions for Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for battery

chargers.

• Before using charger, read all instructions and cautionary markings on charger, battery pack,

and product using battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside charger.

CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT batteries. Other

types of batteries may burst causing personal injury and damage.

CAUTION: Under certain conditions, with the charger plugged in to the power supply, the

charger can be shorted by foreign material. Foreign materials of a conductive nature such as,

but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept

away from charger cavities. Always unplug the charger from the power supply when there is no

battery pack in the cavity. Unplug charger before attempting to clean.

•DO NOT attempt to charge the battery pack with any chargers other than the ones in

this manual. The charger and battery pack are specifically designed to work together.

•These chargers are not intended for any uses other than charging DEWALT recharge-

able batteries. Any other uses may result in risk of fire, electric shock or electrocution.

•Do not expose charger to rain or snow.

•Pull by plug rather than cord when disconnecting charger. This will reduce risk of

damage to electric plug and cord.

•Make sure that cord is located so that it will not be stepped on, tripped over, or other-

wise subjected to damage or stress.

•Do not use an extension cord unless it is absolutely necessary. Use of improper

extension cord could result in risk of fire, electric shock, or electrocution.

•An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that

is 16 gauge has more capacity than 18 gauge. When using more than one extension to make

up the total length, be sure each individual extension contains at least the minimum wire size.

•Do not place any object on top of charger or place the charger on a soft surface that

might block the ventilation slots and result in excessive internal heat. Place the charg-

er in a position away from any heat source. The charger is ventilated through slots in the top

and the bottom of the housing.

•Do not mount charger on wall or permanently affix charger to any surface. The

charger is intended to use on a flat, stable surface (i.e., table top, bench top).

•Do not operate charger with damaged cord or plug — have them replaced immediately.

•Do not operate charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way. Take it to an authorized service center.

•Do not disassemble charger; take it to an authorized service center when service or

repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution

or fire.

•Disconnect the charger from the outlet before attempting any cleaning. This will

reduce the risk of electric shock. Removing the battery pack will not reduce this risk.

•NEVER attempt to connect 2 chargers together.

•The charger is designed to operate on standard household electrical power (120

Volts). Do not attempt to use it on any other voltage.

SAVE THESE INSTRUCTIONS

Introduction

The DC9000 charger is designed to charge D WALT battery packs in approximately 1 hour. ThisE

charger requires no adjustment and is designed to be as easy as possible to operate. Simply

place your battery pack into the receptacle of a plugged in charger and it will automatically

charge the pack.

Important Safety Instruction for Battery Packs

WARNING: For safe operation, read this manual and manuals originally supplied with tool

before using the charger.

When ordering replacement battery packs, be sure to include catalog number and voltage.

Consult the chart on the last page of this manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using the battery pack and

charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

•Do not incinerate the battery pack even if it is severely damaged or is completely

worn out. The battery pack can explode in a fire. Toxic fumes and materials are created

when lithium ion battery packs are burned.

•Do not charge or use battery in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Inserting or removing the battery from the charger may

ignite the dust or fumes.

•If battery contents come into contact with the skin, immediately wash area with mild

soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 min-

utes or until irritation ceases. If medical attention is needed, the battery electrolyte is com-

posed of a mixture of liquid organic carbonates and lithium salts.

•Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If

symptoms persists, seek medical attention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

• Charge the battery packs only in DEWALT chargers.

•DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations where the temperature may

reach or exceed 105°F (40˚) (such as outside sheds or metal buildings in summer).

WARNING: Never attempt to open the battery pack for any reason. If battery pack case is

cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do

not use a battery pack or charger that has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Damaged

battery packs should be returned to service center for recycling.

WARNING: Fire hazard. Do not store or carry battery so that metal objects can contact

exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes,

product kit boxes, drawers, etc., with loose nails, screws, keys, etc. Transporting batteries can

possibly cause fires if the battery terminals inadvertently come in contact with conduc-

tive materials such as keys, coins, hand tools and the like. The US Department of

Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in

commerce or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are

properly protected from short circuits. So when transporting individual batteries, make sure that

the battery terminals are protected and well insulated from materials that could contact them

and cause a short circuit.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the lithium

ion battery (or battery pack) indicates that the costs to recycle the battery (or

battery pack) at the end of its useful life have already been paid by DEWALT.

RBRC™ in cooperation with D WALT and other battery users, has establishedE

programs in the United States to facilitate the collection of spent lithium ion

batteries. Help protect our environment and conserve natural resources by returning the spent

lithium ion battery to an authorized DEWALT service center or to your local retailer for recycling.

You may also contact your local recycling center for information on where to drop off the spent

battery.

RBRC™ is a registered trademark of the

Rechargeable Battery Recycling Corporation.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct sunlight and excess heat

or cold.

2. Long storage will not harm the battery pack or charger. Under proper conditions, they can

be stored for 5 years or more.

Charger

Your battery pack requires a 1 hour D WALT charger. Be sure to read all Esafety instructions

before using your charger. Consult the chart on the back of this manual for compatibility

of chargers and battery packs.

Charging Procedure

1. Plug the charger into an appropriate outlet before inserting the battery pack.

2. Insert the battery pack into the charger. The charger is equipped with a three-light fuel gauge

that will blink according to the state of charge of the battery pack.

3. The completion of charge is indicated by the three red lights remaining ON continuously.

The pack is fully charged and may be used at this time or left on the charger.

Charger Diagnostics

This charger is designed to detect certain problems that can arise with the battery packs or the

charger. Problems are indicated by the three red lights flashing together in different patterns.

PROBLEM POWER LINE

When the charger is used with some portable power sources such as generators or sources that

convert DC to AC, the charger may temporarily suspend operation. The three red lights will flash

together with two fast blinks followed by a pause. This indicates that the power source is out

of limits.

BAD BATTERY

The charger can detect a weak or damaged battery. The three red lights will flash together with

rapid blinking. The battery will no longer charge and should be returned to a service center or

a collection site for recycling.

BAD CHARGER

The charger will detect if it is not functioning properly. The three red lights will flash together with

one fast blink followed by a long blink. The charger will no longer work and should be

returned to an authorized service center or replaced.

LEAVING THE BATTERY IN THE CHARGER

The charger and battery pack can be left connected with the red lights glowing indefinitely. The

charger will keep the battery pack fresh and fully charged. This charger features an automatic

tune-up mode which equals or balances the individual cells in the battery pack to allow it to func-

tion at peak capacity. Battery packs should be tuned up weekly or whenever the battery no

longer delivers the same amount of work. To use the automatic tune-up mode, place the battery

pack in the charger and leave it for at least 8 hours.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when the

air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in

an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and

will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a normal

condition, and does not indicate a problem. To facilitate the cooling of the battery pack after

use, avoid placing the charger or battery pack in a warm environment such as in a metal

shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check current at receptacle by plugging in a lamp or other appliance

b. Check to see if receptacle is connected to a light switch which turns power off when you

turn out the lights.

c. Move charger and battery pack to a location where the surrounding air temperature is

approximately 65°F - 75°F (18°- 24°C).

d. If charging problems persist, take the tool, battery pack and charger to your local

service center.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs which

were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum

foil, or any buildup of metallic particles should be kept away from charger cavities. Always

unplug the charger from the power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Do not allow any liquid to get inside charger.

CAUTION: Never attempt to open the battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service center for recycling.

KEY FEATURES AND FUNCTIONS

Variable Speed Switch (Fig. 1)

To turn the tool on, squeeze the trigger switch (A). To turn the tool off, release the trigger switch.

Your tool is equipped with a brake. The chuck will stop as soon as the trigger switch is fully

released.

NOTE: Continuous use in variable speed range is not recommended. It may damage the switch

and should be avoided.

Forward/Reverse Control Button (Fig. 1)

A forward/reverse control button (B) determines the direction the tool will spin and also serves

as a lock-off button.

To select forward rotation, release the trigger switch and depress the forward/reverse control

button on the right side of the tool.

To select reverse, depress the forward/reverse control button on the left side of the tool.

The center position of the control button locks the tool in the OFF position. When changing the

position of the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click

on start up. This is normal and does not indicate a problem.

Mode Control Collar

Your drill is equipped with a separate mode control collar (Fig. 1, C) to switch between drilling

and screwdriving.

SCREWDRIVING (FIG. 2)

1. Select the desired speed/torque range using the three-speed gear shifter (E) on the top of

tool to match the speed and torque to the planned application. To set the torque level to the

proper setting on the clutch collar, initially set the clutch collar at a lower setting to ensure

the fastener to be set to your specification.

NOTE: Use the lowest torque setting required to seat the fastener at the desired depth. The

lower the number, the lower the torque output.

2. Rotate the mode control collar (C) so the line on the lever (F) is aligned with the screw

symbol.

3. Set the torque adjustment collar (D) to the appropriate number setting for the torque desired.

NOTE: The torque adjustment collar may be set on any number and change between

screwdriving and drilling modes using the mode control collar.

DRILLING (FIG. 3)

CAUTION: When the mode collar is in the drill/hammerdrill mode, the drill will not clutch out

regardless of the position of the torque adjustment collar (D).

Rotate the mode control collar (C) so that the line on the lever (F) is aligned with the drill

symbol.

NOTE: The torque adjustment collar (D) may be set on any number.

HAMMERDRILLING (FIG. 4)

Rotate the mode control collar (C) to align the line on the lever (F) with the hammerdrill

symbol and turn the torque adjustment collar (D) to align the hammer symbol with the line (F).

Torque Adjustment Collar (Fig. 2)

Your tool has an adjustable torque screwdriver mechanism for driving and removing a wide

array of fastener shapes and sizes and a hammer mechanism for drilling into masonry. Circling

the torque adjustment collar (D) are numbers and a hammer symbol. These numbers are used

to set the clutch to deliver a torque range. The higher the number on the collar, the higher the

torque and the larger the fastener which can be driven. To select any of the numbers, rotate until

the desired number aligns with the arrow.

Three-Speed Gearing (Fig. 2)

The three-speed feature of your tool allows you to shift gears for greater versatility. To select

speed 1 (highest torque setting), turn the tool off and permit it to stop. Slide the gear shifter (E) all

the way to the left. Speed 2 (middle torque and speed setting) is in the middle position. Speed 3

(highest speed setting) is to the right.

NOTE: Do not change gears when the tool is running. Always allow the drill to come to a complete

stop before changing gears. If you have trouble changing gears, make sure that the gear shifter is

engaged in one of the three speed settings.

Self-Tightening Chuck Operation (Fig. 5–7)

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front

part of the chuck and turning the tool on. Damage to the chuck and personal injury may result.

Always lock off trigger switch when changing accessories.

0% - 33% 1st light blinks

33% - 66% 1st light on, 2nd light blinks

66% - 99% 1st, 2nd lights on, 3rd light blinks

100% 1st, 2nd, 3rd lights on

WARNING: Always ensure the bit is secure before starting the tool. A loose bit may eject

from tool causing possible personal injury.

TO INSERT A DRILL BIT OR OTHER ACCESSORY

1. Lock the trigger in the OFF position.

2. Grasp the chuck sleeve (G) with one hand and use the other hand to secure the tool as

shown in Figure 5. Rotate the sleeve counterclockwise (viewed from the front) far enough

to accept the desired accessory.

3. Insert the bit or other accessory about 3/4" (19mm) into the chuck, as shown in Figure 6.

Grasp the chuck sleeve securely and rotate the sleeve clockwise (viewed from the front)

with one hand while using the other hand to secure the tool. Rotate the sleeve clockwise

until sleeve cannot be rotated any further, as demonstrated in Figure 7. As the drill is being

operated in the forward position, the chuck will continually self-tighten the jaws of the chuck

onto the bit to maximize the bit gripping strength.

To release the accessory, repeat Step 2.

OPERATION

Installing and Removing the Battery Pack (Fig. 8, 9)

NOTE: Make sure your battery pack is fully charged.

CAUTION: Make certain the lock-off button (B), as shown in Figure 1, is engaged to prevent

switch actuation before removing or installing battery.

To install the battery pack into the tool handle, align the base of the tool with the rails inside

the tool’s handle and slide the battery pack firmly into the handle until you hear the lock snap

into place (Fig. 8).

To remove the battery pack from the tool, press the release button (H) and firmly pull the

battery pack out of the tool handle. Insert it into the charger (Fig. 9) as described in the charger

section of this manual.

Side Handle

CAUTION: Always operate the tool with the side handle properly

assembled. Hold tool with both hands to maximize control.

Side handle clamps to the front of the gear case as shown and may be

rotated to permit right- or left-hand use. Side handle must be tightened

sufficiently to resist the twisting action of the tool if the accessory binds or

stalls. Be sure to grip the side handle at the far end to control the tool dur-

ing a stall.

If model is not equipped with side handle, grip drill with one hand on the handle and one hand

on the battery pack.

Drill Operation

1. Select the desired speed/torque range using the gear shifter to match the speed and torque

to the planned operation.

2. For WOOD, use twist bits, spade bits, power auger bits or hole saws. For METAL, use high-

speed steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The

exceptions are cast iron and brass which should be drilled dry.

3. Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill

bit biting, but do not push hard enough to stall the motor or deflect the bit.

4. Hold tool firmly with both hands to control the twisting action of the drill.

5. IF DRILL STALLS, it is usually because it is being overloaded. RELEASE TRIGGER

IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT

CLICK TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL – THIS

CAN DAMAGE THE DRILL.

6. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent

jamming.

Hammerdrill Operation

1. When drilling, use just enough force on the hammer to keep it from bouncing excessively or

“rising” off the bit. Too much force will cause slower drilling speeds, overheating, and a lower

drilling rate.

2. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the

bit when drilling as this will cause clogging of the bit flutes and a slower drilling speed.

3. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of

the hole with the tool still running to help clear debris from the hole.

4. For MASONRY, use carbide-tipped bits or masonry bits. A smooth, even flow of dust indi-

cates the proper drilling rate.

Screwdriver Operation

Select the desired speed/torque range using the three-speed gear shift lever on the top of tool

to match the speed and torque to the planned operation. Insert the desired fastener accessory

into the chuck as you would any drill bit. Set the torque adjustment collar (D) to the desired

setting. Make a few practice runs in scrap or unseen areas to determine the proper position of

the clutch collar.

FIG. 1

FIG. 2 FIG. 3 FIG. 4

E E

SCREWDRIVING

VISSAGE

DESTORNILLADOR

DRILLING

PERÇAGE

TALADRO

HAMMERDRILLING

MARTEAU PERFORATEUR

TALADRO PERCUTOR

FIG. 8 FIG. 9

FIG. 5 FIG. 6 FIG. 7

4) UTILISATION ET ENTRETIEN DES OUTILS ÉLECTRIQUES

a) Ne pas forcer un outil électrique. Utiliser l’outil approprié au travail en cours. L’outil

approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse pour laquelle il

a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout appareil

dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche du secteur et/ou le bloc-piles de l’outil électrique avant de faire

tout réglage ou changement d’accessoire, ou avant de ranger ce dernier. Ces

mesures préventives réduisent les risques de démarrage accidentel de l’appareil.

d) Après usage, ranger les outils électriques hors de la portée des enfants, et ne

permettre à aucune personne n’étant pas familière avec un outil électrique (ou son

manuel d’instruction) d’utiliser ce dernier. Les outils peuvent être dangereux entre les

mains des novices.

e) Entretenir les outils électriques. Vérifier les pièces mobiles pour s’assurer qu’elles

sont bien alignées et tournent librement, qu’elles sont en bon état et ne sont

affectées d’aucune condition susceptible de nuire au bon fonctionnement de l’outil.

En cas de dommage, faire réparer l’outil électrique avant toute nouvelle utilisation.

Bien des accidents sont causés par des outils mal entretenus.

f) Maintenir tout outil de coupe bien aiguisé et propre. Les outils de coupe bien

entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles à contrôler.

g) Utiliser un outil électrique, ses accessoires, mèches, etc., conformément aux

présentes directives et suivant la manière prévue pour ce type particulier d’outil

électrique, en tenant compte des conditions de travail et du travail à effectuer.

L’utilisation d’un outil électrique pour toute opération autre que celle pour laquelle il a été

conçu est dangereuse.

5) UTILISATION ET ENTRETIEN DE L'OUTIL ALIMENTÉ PAR PILE

a) S’assurer que l’interrupteur se trouve à la position d'arrêt avant d’insérer le bloc-

piles. Insérer un bloc-piles dans un outil électrique dont l’interrupteur est à la position de

marche risque de provoquer un accident.

b) Ne recharger l'outil qu'au moyen du chargeur précisé par le fabricant. L’utilisation

d’un chargeur qui convient à un type de bloc-piles risque de provoquer un incendie s’il est

utilisé avec un autre type de bloc-piles.

c) Utiliser les outils électriques uniquement avec les blocs-piles conçus à cet effet.

L’utilisation de tout autre bloc-piles risque de causer des blessures ou un incendie.

d) Lorsque le bloc-piles n’est pas utilisé, le tenir éloigné des objets métalliques,

notamment des trombones, de la monnaie, des clés, des clous, des vis, etc., qui

peuvent établir une connexion entre les deux bornes. Mettre en court-circuit les

bornes du bloc-piles peut provoquer des brûlures ou un incendie.

e) En cas d’utilisation abusive, un liquide peut gicler hors du bloc-piles, éviter tout

contact. Si un contact accidentel se produit, laver à grande eau. Si le liquide entre

en contact avec les yeux, obtenir des soins médicaux. Le liquide qui gicle hors du

bloc-piles peut provoquer des irritations ou des brûlures.

6) SERVICE

a) Faire entretenir les outils électriques par un réparateur qualifié en n’utilisant que

des pièces de rechange identiques. Cela permettra d’assurer l’intégrité de l’outil

électrique et la sécurité de l’utilisateur.

Règles de sécurité spécifiques pour les marteaux

perforateurs

•Tenir l'outil par sa surface de prise isolée dans une situation où l'outil de coupe

peut entrer en contact avec un câblage dissimulé ou avec son propre cordon

d'alimentation. Tout contact avec un fil « sous tension » mettra « sous tension » les pièces

métalliques de l'outil et électrocutera l'opérateur de l'outil.

•Porter des protecteurs auditifs si une perceuse à percussion est utilisée. Une exposi-

tion au bruit peut entraîner une perte auditive.

•Utiliser les poignées auxiliaires fournies avec l'outil. Une perte de maîtrise de l'outil peut

entraîner des blessures corporelles.

• Utiliser des brides de fixation ou tout autre dispositif de fixation permettant de

soutenir et de retenir la pièce sur une plate-forme stable. Tenir la pièce avec la main ou

contre son corps est instable et risque de provoquer une perte de maîtrise de l'outil.

•Porter des protecteurs auditifs lors de martelage sur des périodes prolongées. Une

exposition prolongée à un bruit d'intensité élevé peut provoquer une perte auditive. Les

niveaux sonores élevés produits par le marteau perforateur pourraient provoquer une perte

auditive temporaire ou endommager gravement les tympans.

•Porter des lunettes de sécurité ou une autre protection oculaire. . Le martelage et la

perforation peuvent projeter des fragments. Les particules projetées peuvent endommager

les yeux irréversiblement.

•Toujours utiliser la poignée latérale fournie avec l'outil. Tenir fermement l'outil en tout

temps. Ne pas utiliser l'outil sans le tenir des deux mains.

•Les mèches à maçonnerie et les outils deviennent chauds en cours de fonction-

nement. Pour les toucher, porter des gants.

AVERTISSEMENT : TOUJOURS uporter des lunettes de sécurité. Les lunettes de vue ne

constituent PAS des lunettes de sécurité. Utiliser également un masque facial ou anti-poussière

si l'opération de découpe génère de la poussière. TOUJOURS PORTER UN ÉQUIPEMENT DE

PROTECTION HOMOLOGUÉ :

• protection oculaire conforme à la norme ANSI Z87.1 (CAN/CSA Z94.3),

• protection auditive conforme à la norme ANSI S12.6 (S3.19) et

• protection des voies respiratoires conformes aux normes NIOSH/OSHA.

AVERTISSEMENT : Certains outils électriques, tels que les sableuses, les scies, les meules,

les perceuses ou certains autres outils de construction, peuvent produire de la poussière con-

tenant des produits chimiques susceptibles d’entraîner le cancer, des malformations congéni-

tales ou pouvant être nocifs pour le système reproductif. Parmi ces produits chimiques, on

retrouve :

• le plomb dans les peintures à base de plomb,

• la silice cristalline dans les briques et le ciment et autres produits de maçonnerie,

• l’arsenic et le chrome dans le bois de sciage ayant subi un traitement chimique (comme

l’arséniate de cuivre et de chrome).

Le risque associé à de telles expositions varie selon la fréquence avec laquelle on effectue ces

travaux. Pour réduire l’exposition à de tels produits, il faut travailler dans un endroit bien aéré et

utiliser le matériel de sécurité approprié, tel un masque anti-poussières spécialement conçu

pour filtrer les particules microscopiques.

•Éviter tout contact prolongé avec la poussière soulevée par cet outil ou autres outils

électriques. Porter des vêtements de protection et nettoyer les parties exposées du

corps à l’eau savonneuse. S’assurer de bien se protéger afin d’éviter d’absorber par la

bouche, les yeux ou la peau des produits chimiques nocifs.

AVERTISSEMENT : Cet outil peut produire et répandre de la poussière susceptible de causer

des dommages sérieux et permanents au système respiratoire. Toujours utiliser un appareil res-

piratoire anti-poussières approprié approuvé par le NIOSH ou l’OSHA. Diriger les particules

dans le sens opposé du visage et du corps.

MISE EN GARDE : Après utilisation, ranger l’outil sur son côté sur une surface stable

là où il ne pourra faire ni trébucher ni tomber personne. Bien que certains outils munis d’un

gros bloc-pile puissent être placés à la verticale, dans cette position, ils peuvent facilement être

renversés.

MISE EN GARDE : Porter un appareil de protection personnel anti-bruit approprié

durant l’utilisation. Sous certaines conditions et pendant toute la durée de l’utilisation, le bruit

émanant de ce produit pourrait contribuer à la perte d’audition.

• L’étiquette apposée sur l’outil peut afficher les symboles suivants. Ces symboles et leurs déf-

initions sont les suivants :

V..................volts A ..................ampères

Hz................hertz W..................watts

min ..............minutes ................courant alternatif

............courant continu no ................aucune option à vide

................Construction de classe I ..................vitesse à vide

....................(mis à la terre) ..................symbole d’avertissement

................Construction de classe II …/min ..........rotations ou alternance

.................... ....................(à double isolation) alternatifs par minute

BPM ............coups par minute

Directives de sécurité importantes pour les chargeurs

de piles

CONSERVER CES DIRECTIVES : Ce manuel contient des directives de sécurité importantes

sur les chargeurs de piles.

• Avant d’utiliser le chargeur, lire toutes les directives et les indications d'avertissement

figurant sur le chargeur, le bloc-piles et le produit utilisé avec le bloc-piles.

AVERTISSEMENT : Risque de choc. Éviter la pénétration de tout liquide dans le chargeur.

MISE EN GARDE : Risque de brûlure. Pour réduire le risque de blessures, charger seulement

les piles DEWALT. D’autres types de piles peuvent exploser et causer des blessures corporelles

et des dommages.

MISE EN GARDE : Sous certaines conditions, lorsque le chargeur est branché au bloc d’ali-

mentation, le chargeur peut être court-circuité par des corps étrangers. Tout corps étranger con-

ducteur, tel que, mais sans s'y limiter, la laine d'acier, le papier d'aluminium, ou toute accumu-

lation de particules métalliques, doit être maintenu à distance des ouvertures du chargeur.

Débrancher systématiquement le chargeur si aucun bloc-piles n’y est inséré. Débrancher le

chargeur avant tout nettoyage.

•NE PAS charger le bloc-piles au moyen de tout autre chargeur que ceux mentionnés

dans le présent manuel. Le chargeur et le bloc-piles sont spécialement conçus pour être

utilisés ensemble.

•Ces chargeurs ne sont pas prévus pour être utilisés à d’autres fins que celles de

charger les piles rechargeables DEWALT. Toute autre utilisation risque de provoquer un

incendie, un choc électrique ou une électrocution.

•Ne pas exposer le chargeur à la pluie ou à la neige.

•Tirer sur la fiche plutôt que sur le cordon pour débrancher le chargeur. Cela permet

de réduire le risque d’endommager la fiche ou le cordon d’alimentation.

•S’assurer que le cordon est situé en lieu sûr de manière à ce que personne ne marche

ni ne trébuche dessus ou à ce qu’il ne soit pas endommagé ni soumis à une tension.

•Ne pas utiliser de rallonge à moins que cela ne soit absolument nécessaire.

L’utilisation d’une rallonge inadéquate risque d’entraîner un incendie, un choc électrique

ou une électrocution.

•La rallonge utilisée doit présenter un calibre adéquat (AWG ou calibrage américain

normalisé des fils) pour assurer la sécurité. Plus le numéro de calibre de fil est petit et

plus sa capacité est grande, par exemple un calibre 16 a plus de capacité qu’un calibre 18.

Si plus d’une rallonge est utilisée pour obtenir la longueur totale, s’assurer que chaque ral-

longe présente au moins le calibre de fil minimum.

•Ne pas mettre d’objet sur le chargeur ni mettre ce dernier sur une surface molle

pouvant obstruer les fentes de ventilation et ainsi provoquer une chaleur interne

excessive. Mettre le chargeur à un endroit éloigné de toute source de chaleur. La ventila-

tion du chargeur se fait par les fentes pratiquées dans les parties supérieures et inférieures

du boîtier.

MAINTENANCE

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To

minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when

performing this. Exterior plastic parts may be cleaned with a damp cloth and mild detergent.

Although these parts are highly solvent resistant, use solvents.NEVER

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt

and grease may be removed from the exterior of the charger using a cloth or soft non-metallic

brush. Do not use water or any cleaning solutions.

Repairs

The charger is not user serviceable. There are no user serviceable parts inside the charger.

Servicing at an authorized service center is required to avoid damage to static sensitive internal

components.

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including

brush inspection and replacement) should be performed by a DEWALT factory service center, a

DEWALT authorized service center or other qualified service personnel. Always use identical

replacement parts.

Accessories

Recommended accessories for use with your tool are available at extra cost from your local

service center.

CAUTION: The use of any non-recommended accessory may be hazardous.

If you need any assistance in locating any accessory, please contact DEWALT Industrial Tool

Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or

visit our website www.dewalt.com.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three

years from the date of purchase. This warranty does not cover part failure due to normal wear

or tool abuse. For further detail of warranty coverage and warranty repair information, visit

www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to

accessories or damage caused where repairs have been made or attempted by others. This

warranty gives you specific legal rights and you may have other rights which vary in certain

states or provinces.

In addition to the warranty, DEWALT tools are covered by our:

1 YEAR FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year after purchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9096, DC9091, DC9071 and DC9360

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or

Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt

for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products

sold in Latin America, see country specific warranty information contained either in the packag-

ing, call the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are miss-

ing, call 1-800-4-DEWALT for a free replacement.

Patent Notification

Manufactured under one or more of

the following U.S. patents:

6859013

6329788

6175211

6133713

6057608

6653815

6431289

6676557

6857983

6984188

Other patents pending.

SI VOUS AVEZ DES QUESTIONS OU VOULEZ NOUS FAIRE PART DE VOS COMMEN-

TAIRES CONCERNANT CET OUTIL OU TOUT AUTRE OUTIL DEWALT, COMPOSEZ SANS

FRAIS LE : 1 800 433-9258.

Règles de sécurité – Généralités

AVERTISSEMENT : Lire toutes ces directives. Tout manquement aux directives

suivantes pose des risques de choc électrique, d’incendie et/ou de blessure

grave. Le terme « outil électrique » dans tous les avertissements ci-après se rapporte

à votre outil électrique à alimentation sur secteur (avec fil) ou par piles (sans fil).

CONSERVER CES DIRECTIVES

1) SÉCURITÉ - AIRE DE TRAVAIL

a) Maintenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont

propices aux accidents.

b) Ne pas faire fonctionner un outil électrique dans une atmosphère explosive, en

présence par exemple de poussières, gaz ou liquides inflammables. Les outils

électriques peuvent engendrer des étincelles qui pourraient enflammer toute émanation

ou poussière ambiante.

c) Tenir les enfants, ou toute autre personne, éloignés pendant l’utilisation d’un outil

électrique. Toute distraction pourrait vous faire perdre la maîtrise de ce dernier.

2) SÉCURITÉ – ÉLECTRICITÉ

a) La fiche électrique de l’outil doit correspondre à la prise murale. Ne jamais

modifier la fiche en aucune façon. Ne jamais utiliser de fiche d’adaptation avec un

outil électrique mis à la terre. L’utilisation de fiches d’origine et de prises appropriées

réduira les risques de choc électrique.

b) Éviter tout contact corporel avec des éléments mis à la terre comme tuyaux,

radiateurs, cuisinières ou réfrigérateurs. Les risques de choc électrique augmentent

lorsque le corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. Toute pénétration d’un

outil électrique par un liquide augmente les risques de choc électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour

transporter, tirer ou débrancher un outil électrique. Protéger le cordon de la chaleur,

de l’huile et de tout bord tranchant ou pièce mobile. Les cordons endommagés ou

emmêlés augmentent les risques de choc électrique.

e) Lors de l’utilisation d’un outil électrique à l’extérieur, n’utiliser que des rallonges

conçues pour l’extérieur. L’utilisation d’une rallonge conçue pour l’extérieur réduit les

risques de choc électrique. En cas d’utilisation d’une rallonge, s’assurer que les valeurs

nominales de la rallonge utilisée correspondent bien à celles de l’outil alimenté. L’usage

d’une rallonge de calibre insuffisant causera une chute de tension entraînant perte de

puissance et surchauffe. Le tableau ci-dessous illustre les calibres à utiliser selon la

longueur de rallonge et l’intensité nominale indiquée sur la plaque signalétique. En cas de

doutes, utiliser le calibre suivant. Plus le calibre est petit, plus la rallonge peut supporter

de courant.

Calibre de fil minimum recommandé pour les rallonges

Longueur totale de la rallonge

25 pi 50 pi 75 pi 100 pi 125 pi 150 pi 175 pi

7,6 m 15,2 m 22,9 m 30,5 m 38,1 m 45,7 m 53,3 m

Calibre AWG

18 18 16 16 14 14 12

3) SÉCURITÉ PERSONNELLE

a) Rester vigilant en tout temps et faire preuve de jugement pendant l’utilisation d’un

outil électrique. Ne pas utiliser d’outil électrique en cas de fatigue ou sous l’influ-

ence de drogues, d’alcool ou de médicaments. Tout moment d’inattention pendant

l’utilisation d’un outil électrique pose des risques de blessure grave.

b) Utiliser le matériel de sécurité approprié. Toujours porter des lunettes de protection.

Le fait de porter un masque anti-poussières, des chaussures antidérapantes, un casque

de sécurité ou des protecteurs auditifs lorsque la situation le requiert réduira les risques

de blessure.

c) Éviter tout démarrage accidentel. S’assurer que l’interrupteur est en position

d’arrêt avant tout branchement. Transporter un outil le doigt sur l’interrupteur ou

brancher un outil électrique alors que l’interrupteur est en position de marche invite les

accidents.

d) Retirer toute clé de réglage avant de démarrer l’outil. Une clé laissée sur une pièce

rotative d’un outil électrique pose des risques de blessure.

e) Ne pas effectuer de travaux hors de portée. Les pieds doivent rester bien ancrés au

sol afin de maintenir son équilibre en tout temps. Cela permet de mieux maîtriser l’outil

électrique dans les situations imprévues.

f) Porter des vêtements appropriés. Ne pas porter de vêtements amples ni de bijoux.

Maintenir cheveux, vêtements et gants éloignés des pièces mobiles. Vêtements

amples, bijoux ou cheveux longs risquent de rester coincés dans ces pièces mobiles.

Prendre des précautions autour des évents car ils recouvrent des pièces mobiles.

g) Lorsque un dispositif de connexion à un système de dépoussiérage ou d’élimina-

tion est fourni, s’assurer qu’il est connecté et utilisé correctement. L’utilisation de ces

dispositifs peut réduire les risques engendrés par les poussières.

Product specificaties

Merk:	DeWalt
Categorie:	Boormachine
Model:	DC900KL

Heb je hulp nodig?

Als je hulp nodig hebt met DeWalt DC900KL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Boormachine DeWalt

DeWalt DW9106 Handleiding

15 November 2024

DeWalt DCB126 Handleiding

2 November 2024

DeWalt DCH033 Handleiding

11 September 2024

DeWalt DWD216G Handleiding

29 Augustus 2024

DeWalt DCD445 Handleiding

27 Augustus 2024

DeWalt DW235G Handleiding

26 Augustus 2024

DeWalt DC987-XE Handleiding

15 Juli 2024

DeWalt DW922K2 Handleiding

15 Juli 2024

DeWalt DCD932 Handleiding

15 Juli 2024

DeWalt D21717 Handleiding

15 Juli 2024

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine

Milwaukee M12 BDDXKIT Handleiding

16 November 2024

Metabo BS 12 BL Q Handleiding

15 November 2024

Gude GTB 16/12 R+L Handleiding

15 November 2024

MSW -DMS400 Handleiding

4 November 2024

Vonroc CD510DC Handleiding

20 Oktober 2024

MSW -DDM300 Handleiding

16 Oktober 2024

MSW ACC-B1 Handleiding

16 Oktober 2024

MSW -DDM260 Handleiding

16 Oktober 2024

MSW -DDM132 Handleiding

16 Oktober 2024

MSW -DDM230 Handleiding

16 Oktober 2024