DeWalt D25324K Handleiding

DeWalt Boormachine D25324K

Lees hieronder de 📖 handleiding in het Nederlandse voor DeWalt D25324K (7 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286

D25123, D25213, D25313, D25223, D25323, D25324, D25330

The following are trademarks for one or more D WALT power tools: the yellow and black color scheme, the E

“D” shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of

lozenge-shaped humps on the surface of the tool.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D WALT • www.dewalt.comE

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result

in .death or serious injury

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury.

NOTICE: may Indicates a practice which, if not avoided, not related to personal injury

result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D WALT TOOL, CALL E

US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault

circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or

a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) The Do not force the power tool. Use the correct power tool for your application.

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could result

in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Additional Safety Instructions for Rotary Hammers

• Wear ear protectors. Exposure to noise can cause hearing loss.

• Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.

• Hold power tools by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord. Cutting accessory

contacting a “live” wire will make exposed metal parts of the power tool “live” and could give

the operator an electric shock.

• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

• Wear safety goggles or other eye protection. Hammering operations cause chips to

fly. Flying particles can cause permanent eye damage. Wear a dust mask or respirator for

applications that generate dust. Ear protection may be required for most applications.

• Keep a firm grip on the tool at all times. Do not attempt to operate this tool without

holding it with both hands. It is recommended that the side handle be used at all times.

Operating this tool with one hand will result in loss of control. Breaking through or encountering

hard materials such as re-bar may be hazardous as well. Tighten the side handle securely before

use.

• Do not use this tool to mix or pump easily combustible or explosive ﬂuids (benzine, alcohol, etc.).

• Do not mix or stir inﬂammable liquids labelled accordingly.

• Do not operate this tool for long periods of time. Vibration caused by hammer action may

be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by

taking frequent rest periods.

• Do not recondition bits yourself. Chisel reconditioning should be done by an authorized

specialist. Improperly reconditioned chisels could cause injury.

• Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and

bits may get extremely hot during operation. Small bits of broken material may damage bare

hands.

• Never lay the tool down until the bit has come to a complete stop. Moving bits could

cause injury.

• Do not strike jammed bits with a hammer to dislodge them. Fragments of metal or

material chips could dislodge and cause injury.

• Slightly worn chisels can be resharpened by grinding.

• Keep the power cord away from the rotating bit. Do not wrap the cord around any part

of your body. An electric cord wrapped around a spinning bit may cause personal injury and

loss of control.

• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long

hair can be caught in moving parts.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using more than one extension to make up

the total length, be sure each individual extension contains at least the minimum wire size. The

following table shows the correct size to use depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the

cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use

face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their definitions are

as follows:

V .....................volts A .........................amperes

Hz ...................hertz W ........................watts

min .................minutes or AC .............alternating current

or DC .....direct current or AC/DC......alternating or direct current

...................Class I Construction no .......................no load speed

....

............

....

............

....

............

....

............

....

...........

...

......(grounded) n .........................rated speed

................... Class II Construction .......................earthing terminal

(double insulated) ........................safety alert symbol

…/min ............per minute BPM ...................beats per minute

IPM .................impacts per minute RPM ...................revolutions per minute

SPM ...............strokes per minute sfpm ...................surface feet per minute

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Motor

Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than

10% will cause loss of power and overheating. DEWALT tools are factory tested; if this tool does

not operate, check power supply.

COMPONENTS (Fig. 1)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

A. Variable speed switch F. Chuck

B. Active vibration handle G. Dust cover

(D25223, D25323, D25324 only) H. Depth adjustment rod

C. Forward/reverse slider (D25123, D25213, I. Side handle

D25313, D25223, D25323, D25324) J. Depth stop button

D. Mode selector (D25123, D25213, K. Locking collar (D25324 only)

D25313, D25223, D25323, D25324) L. Lock-on button (D25123, D25330 only)

E. Mode selector button (D25123, D25213, M. Chisel rotation (D25330 only)

D25313, D25223, D25323, D25324)

INTENDED USE

These heavy-duty rotary hammers have been designed for professional drilling and hammerdrilling,

screwdriving and light chipping at various work sites (i.e., construction sites). use under DO NOT

wet conditions or in presence of flammable liquids or gases.

These heavy-duty rotary hammers are professional power tools. let children come into DO NOT

contact with the tool. Supervision is required when inexperienced operators use this tool.

D25123, D25213, D25313, D25223, D25323, D25324 Heavy-Duty 1" (26 mm) SDS Plus ® Rotary Hammers

D25330 Heavy-Duty SDS Plus® Chipping Hammer

Marteaux rotatifs industriels SDS Plus®, 26 mm (1po), D25223, D25323, D25324D25123, D25213, D25313,

Marteau burineur industriel SDS Plus® D25330

Rotomartillos SDS Plus® de 26 mm (1") para trabajos pesados D25123, D25213, D25313, D25223,

D25323, D25324 Martillo de soldador SDS Plus® para trabajos pesados D25330

Active Vibration Control (Fig. 1)

D25223, D25323 AND D25324 ONLY

The active vibration control reduces rebound vibration from the hammer mechanism. Reducing

hand and arm vibration allows for more comfortable use for longer periods of time and extends the

life ofthe unit.

For best vibration control, hold the tool with one hand on the main handle (B) and the other hand

on the side handle (I). Apply just enough pressure so the hammer is approximately mid-stroke.

The hammer only needs enough pressure to engage the active vibration control. Applying too much

pressure will not make the tool drill or chip faster and active vibration control will not engage.

Torque Limiting Clutch

All rotary hammer drills are equipped with a torque limiting clutch that reduces the maximum

torque reaction transmitted to the operator in case of jamming of a drill bit. This feature

also prevents the gearing and electric motor from stalling. The torque limiting clutch has been

factory-set and cannot be adjusted.

Side Handle (Fig. 2)

WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side handle

properly installed and securely tightened. Failure to do so may result in the side handle slipping

during tool operation and subsequent loss of control. Hold tool with both hands to maximize control.

A side handle comes assembled with this rotary hammer. The side handle (I) can be ﬁtted to suit

both right-hand and left-hand users.

TO ADJUST THE SIDE HANDLE

1. Loosen the side handle (I) by turning it counterclockwise.

2. Rotate the side handle to the desired position.

3. Tighten the side handle by turning it clockwise.

TO CHANGE SIDES

For right-hand users: slide the side handle clamp over the chuck, handle at the left.

For left-hand users: slide the side handle clamp over the chuck, handle at the right.

Trigger Switch (Fig. 1)

To start the rotary hammer, depress the trigger switch (A). To stop rotary hammer, release the

switch.

NOTE: Use lower speeds for starting holes without a centerpunch, drilling in metal, plastics or

ceramics, or driving screws. Higher speeds are better for drilling in masonry for maximum efficiency.

VARIABLE SPEED

The variable speed trigger switch (A) permits speed control. The farther the trigger switch is

depressed, the higher the speed of the drill.

Lock-on Button (Fig. 1)

D25123, D25330

WARNING: Be sure to release the locking mechanism before disconnecting the plug from the

power supply. Failure to do so will cause the hammerdrill to start immediately the next time it is

plugged in. Damage or personal injury could result.

The lock-on button (L) is for use only when the rotary hammer is stationary, mounted in a drill press

stand or for chipping applications.

Before using the tool each time, be sure that the lock-on button release mechanism is working

freely.

D25123 ONLY

To lock the trigger switch in the on position for continuous operation, depress and hold the trigger

switch and slide the lock-off button (L) forward. The tool will continue to run.

To turn the tool off from a locked on condition, squeeze the trigger once then release it.

D25330 ONLY

To lock the trigger switch in the On position for continuous operation, depress the trigger switch

and push the lock-on button (L) in. The tool will continue to run.

To turn the tool Off from a locked on condition, squeeze the trigger once then release it.

Forward/Reverse Slider (Fig. 1)

D25123, D25213, D25313, D25223, D25323, D25324

WARNING: Always wait until the motor has come to a complete standstill before changing the

direction of rotation.

CAUTION: When reversing to clear jammed bits, be ready for strong reactive torque.

The forward/reverse slider (C) is used to reverse the rotary hammer for backing out fasteners or

jammed bits mode.

1. Push the forward/reverse slider (C) to the left (viewed when holding drill in operating position)for

forward (right-hand) rotation. See arrows on tool.

2. Push the forward/reverse slider (C) to the right for reverse (left-hand) rotation.

Mode Selector (Fig. 3)

D25123, D25213, D25313, D25223, D25323, D25324

NOTICE: Tool must come to a complete stop before activating the mode selector button or

damage to the tool may result.

DRILL-ONLY MODE

To use drill-only mode, press mode selector button (E) and turn the mode selector (D) so the yellow

arrow points to the corresponding symbol as shown. Use drill-only mode for wood, metal, and

plastics.

HAMMERDRILL MODE

To use hammerdrill mode, press the mode selector button (E) and turn the mode selector (D) so the

yellow arrow points to the corresponding symbol as shown. Use this mode for masonry drilling.

HAMMER-ONLY MODE

For light chiseling, press the mode selector button (E) and turn the mode selector (D) so the yellow

arrow points to the corresponding symbol as shown.

NOTE: The yellow arrow on the mode selector MUST be aligned with the one of the symbols at

all times. There are no operable positions between the positions.

CHISEL ROTATION

D25313, D25323, D25324

To manually rotate the chisel, depress the button (E) and turn the mode selector (D) so the yellow

arrow points to the corresponding symbol as shown.

SDS Plus® Chuck (Fig. 1)

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool

from power source before making any adjustments or removing/installing attachments

or accessories.

WARNING: Burn Hazard. ALWAYS wear gloves when changing bits. Accessible metal parts on

the tool and bits may get extremely hot during operation. Small bits of broken material may damage

bare hands.

WARNING: Do not attempt to tighten or loosen drill bits (or any other accessory) by gripping the

front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur.

To insert bit, insert shank of bit about 3/4" (19 mm), no further than 7/8" (22 mm) into chuck. Push

and rotate bit until it locks in place. The bit will be securely held.

To release bit, pull the chuck sleeve (F) back and remove the bit.

OPERATION

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power

source before installing and removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is anchored

or clamped firmly. If drilling thin material, use a wood “back-up” block to prevent damage to the

material.

To reduce the risk of personal injury, ALWAYS operate the tool with the side handle

properly installed and securely tightened. Failure to do so may result in the side handle slipping

during tool operation and subsequent loss of control. Hold tool with both hands to maximize control.

Proper Hand Position (Fig. 1, 4)

WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as

shown.

WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation

of a sudden reaction.

Proper hand position requires one hand on the side handle (I), with the other hand on the main

handle (B).

Overload Clutch

If the drill bit becomes jammed or caught, the drive to the drill spindle is interrupted by the overload

clutch. Because of the forces that occur as a result, always hold the machine securely with both

hands and take a firm stance.

Drilling Tools

The machine is intended for hammerdrilling in concrete, brick and stone. It is also suitable for drilling

without impact in wood, metal, ceramic and plastic.

Chipping Tools

The machine is intended for chipping in concrete, brick and stone.

Removable SDS Plus® Chuck and Three Jaw Keyless Chuck

(Fig. 1)

D25324

The D25324 is equipped with a removable quick change SDS Plus® chuck as well as a removable

three jaw keyless chuck. The hammer mechanism does not function when the three jaw keyless

chuck is used.

Both the SDS Plus® and three jaw keyless chuck can be easily removed by turning the locking collar

(K) into the unlocked position to release the chuck.

The SDS Plus®

and three jaw keyless chuck can be easily attached by inserting the chuck into the

spindle of the tool and turning the collar to the locked position. The chuck will click when properly

installed.

FIG. 5

FIG. 1

D25324

FIG. 2

D25330

Drilling

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool

from power source before making any adjustments or removing/installing attachments

or accessories.

WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is anchored

or clamped firmly. If drilling thin material, use a wood “back-up” block to prevent damage to the

material.

Press mode selector button (E) and turn the mode selector (D) to the drill bit symbol for drilling, to the

hammer symbol for hammering or to the hammerdrill symbol for hammerdrilling.

DRILLING OPERATION

1. For WOOD, use twist bits, spade bits, power auger bits or hole saws. For METAL, use high-

speed steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The

exceptions are cast iron and brass which should be drilled dry. For MASONRY, use carbide-

tipped bits or masonry bits. A smooth, even flow of dust indicates the proper drilling rate.

2. Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill bit

biting, but do not push hard enough to stall the motor or deflect the bit.

3. Hold tool firmly with both hands to control the twisting action of the drill.

WARNING: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip

the drill firmly with both hands to control the twisting action and avoid injury.

4. IF DRILL STALLS RELEASE TRIGGER , it is usually because it is being overloaded.

IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK

TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL – THIS CAN

DAMAGE THE DRILL.

5. To minimize stalling or breaking through the material, reduce pressure on drill and ease the bit

through the last fractional part of the hole.

6. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent

jamming.

7. With variable speed drills there is no need to center punch the point to be drilled. Use a slow

speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep

enough to drill without the bit skipping out.

DRILLING IN METAL

An SDS Plus® to round shank adaptor chuck is required for the D25123, D25213, D25313, D25223

and the D25323. Ensure that tool is in drill-only mode. Start drilling with slow speed and increase

to full power while applying firm pressure on the tool. A smooth even flow of metal chips indicates

D25123

D25323

D25223

FIG. 3

DRILL-ONLY MODE

MODE PERÇAGE SEULEMENT

MODO SÓLO TALADRO

HAMMER/DRILL MODE

MODE PERFORATION-PERÇAGE

MODO TALADRO/PERCUTOR

CHISEL ROTATION

ROTATION DU BURIN

ROTACIÓN DE CINCELES

(D25123, D25213, D25223 ONLY)

HAMMER-ONLY MODE

MODE PERFORATION SEULEMENT

MODO SÓLO MARTILLO

CHISEL ROTATION

ROTATION DU BURIN

ROTACIÓN DE CINCELES

(D25313, D25323, D25324 ONLY)

HAMMER/DRILL MODE

MODE PERFORATION-PERÇAGE

MODO TALADRO/PERCUTOR

FIG. 4

the proper drilling rate. Use a cutting lubricant when drilling metals. The exceptions are cast iron

and brass which should be drilled dry.

NOTE: Large [5/16" to 1/2" (7.9 mm to 12.7 mm)] holes in steel can be made easier if a pilot hole

[5/32" to 3/16" (4 mm to 4.8 mm)] is drilled first.

DRILLING IN WOOD

An SDS Plus® to round shank adaptor chuck is required for the D25123, D25213, D25313, D25223

and the D25323. Ensure that tool is in drill-only mode. Start drilling with slow speed and increase to

full power while applying firm pressure on the tool. Holes in wood can be made with the same twist

drills used for metal. These bits may overheat unless pulled out frequently to clear chips from the

flutes. For larger holes, use spade bits, power auger bits, or hole saws. Work that is apt to splinter

should be backed up with a block of wood.

HAMMERDRILL OPERATION

1. When drilling, use just enough force on the hammer to keep it from bouncing excessively or

“rising” off the bit. Too much force will cause slower drilling speeds, overheating, and a lower

drilling rate.

2. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the bit

when drilling as this will cause clogging of the bit flutes and a slower drilling speed.

3. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of the

hole with the tool still running to help clear debris from the hole.

4. For masonry, use carbide-tipped bits or masonry bits. A smooth even flow of dust indicates the

proper drilling rate.

Chipping and Chiselling (Fig. 1)

1. Set the mode selector switch (D) to the hammering only position.

2. Insert the appropriate chisel and rotate it by hand to lock it into one of 51 positions.

3. Adjust the side handle (I) as required.

4. Switch on the tool and start working.

5. Always switch off the tool when work is ﬁnished and before unplugging.

Depth Rod (Fig. 5)

TO ADJUST THE DEPTH ROD

1. Push in and hold the depth rod release button (J) on the side handle.

2. Move the depth rod (H) so the distance between the end of the rod and the end of the bit equals

the desired drilling depth.

3. Release the button to lock rod into position. When drilling with the depth rod, stop when end

of rod reaches surface of material.

MAINTENANCE

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power

source before installing and removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To

minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing

this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts

of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse

any part of the tool into a liquid.

Lubrication

Your tool was properly lubricated before leaving the factory. In from two to six months, depending

upon use, take or send your tool to an authorized service center for a complete cleaning, inspection

and lubrication. Tools used constantly on production jobs will need relubrication more often. Also,

tools “out of service” for long periods should be relubricated before being put back to work.

Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been tested with

this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury,

only DEWALT recommended accessories should be used with this product.

Recommended accessories for use with your tool are available at extra cost from your local dealer or

authorized service center. If you need assistance in locating any accessory, please contact DEWALT

Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-

9258) or visit our website: www.dewalt.com.

MAXIMUM RECOMMENDED CAPACITIES

D25123, D25213, D25313

D25223, D25323, D25324

Masonry 1" (25.4 mm)

Steel 1/2" (12.7 mm)

Wood 1-1/2" (38 mm)

OPTIMUM CAPACITY

Masonry 5/32"–5/8" (4 mm–4.8 mm)

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush

inspection and replacement) should be performed by a DEWALT factory service center, a DEWALT

authorized service center or other qualified service personnel. Always use identical replacement

parts.

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty

service in case there is a problem with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,

your registration of ownership will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event

a safety notification is required under the Federal Consumer Safety Act.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three

years from the date of purchase. This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.

com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to accessories or

damage caused where repairs have been made or attempted by others. This warranty gives you

specific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, D WALT tools are covered by our:E

1 YEAR FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer

for any reason, you can return it within 90 days from the date of purchase with a receipt for a full

refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products

sold in Latin America, see country specific warranty information contained in the packaging, call the

local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing,

call 1-800-4-DEWALT (1-800-433-9258) for a free replacement.

SPECIFICATIONS

D25123, D25213, D25313,

D25223, D25313, D25324 D25330

Voltage: 120 V AC~ 120 V AC~

Ampere rating: 8 A 6.3 A

Frequency: 60 Hz 60 Hz

RPM: 0–1 150/min –

Beats per minute 0–4 300 0–4 100

Déﬁ nitions: lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour chaque

mot-indicateur employé. Lire le mode d’emploi et porter une attention particulière

à ces symboles.

DANGER : indique une situation dangereuse imminente qui, si elle n’est pas

évitée, entraînera la mort ou des blessures graves.

AVERTISSEMENT: indique une situation potentiellement dangereuse qui,

si elle n’est pas évitée, entraîner lapourrait mort ou des blessures graves.

ATTENTION: indique une situation potentiellement dangereuse qui, si elle

n’est pas évitée, entraîner des pourrait blessures légères ou modérées.

AVIS : indique une pratique ne posant aucun risque de dommages corporels

mais qui par contre, si rien n’est fait pour l’éviter, poser despourrait risques de

dommages matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT AUTRE

OUTIL DEWALT, COMPOSEZ LE NUMÉRO SANS FRAIS : 1-800-4-DEWALT (1-800-433-9258).

AVERTISSEMENT : afin de réduire le risque de blessures, lire le mode d’emploi de l’outil.

Avertissements de sécurité généraux pour les outils

électriques

AVERTISSEMENT ! Lire tous les avertissements de sécurité et toutes les directives.

Le non-respect des avertissements et des directives pourrait se solder par un choc

électrique, un incendie et/ou une blessure grave.

CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES

DIRECTIVES POUR UN USAGE ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se rapporte à votre outil électrique à

alimentation sur secteur (avec fil) ou par piles (sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont

propices aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, tel qu’en

présence de liquides, de gaz ou de poussières inflammables. Les outils électriques

produisent des étincelles qui pourraient enflammer la poussière ou les vapeurs.

c) Éloigner les enfants et les personnes à proximité pendant l’utilisation d’un outil

électrique. Une distraction pourrait en faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais modifier

la fiche d’aucune façon. Ne jamais utiliser de fiche d’adaptation avec un outil

électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de fiches

non modifiées correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des tuyaux,

des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc électrique est

plus élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. La pénétration de l’eau

dans un outil électrique augmente le risque de choc électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour

transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de

la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge

convenant à cette application. L’utilisation d’une rallonge conçue pour l’extérieur réduira

les risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit

humide, brancher l’outil dans une prise ou sur un circuit d’alimentation dotés d’un

disjoncteur de fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur réduit les

risques de choc électrique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un outil

électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue ou sous

l’influence de drogues, d’alcool ou de médicaments. Un simple moment d’inattention

en utilisant un outil électrique peut entraîner des blessures corporelles graves.

b) Utiliser des équipements de protection individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection comme un masque antipoussière, des

chaussures antidérapantes, un casque de sécurité ou des protecteurs auditifs lorsque la

situation le requiert réduira les risques de blessures corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve à la

position d’arrêt avant de relier l’outil à une source d’alimentation et/ou d’insérer un

bloc-piles, de ramasser ou de transporter l’outil. Transporter un outil électrique alors

que le doigt repose sur l’interrupteur ou brancher un outil électrique dont l’interrupteur est à

la position de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer l’outil. Une clé ou une clé de

réglage attachée à une partie pivotante de l’outil électrique peut provoquer des blessures

corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet de

mieux maîtriser l’outil électrique dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de bijoux.

Garder les cheveux, les vêtements et les gants à l’écart des pièces mobiles. Les

vêtements amples, les bijoux ou les cheveux longs risquent de rester coincés dans les pièces

mobiles.

g) Si des composants sont fournis pour le raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien raccordés et utilisés. L’utilisation

d’un dispositif de dépoussiérage peut réduire les dangers engendrés par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à l’application.

L’outil électrique approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse

pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil

électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche de la source d’alimentation et/ou du bloc-piles de l’outil

électrique avant de faire tout réglage ou changement d’accessoire ou avant de

ranger l’outil. Ces mesures préventives réduisent les risques de démarrage accidentel de

l’outil électrique.

d) Ranger les outils électriques hors de la portée des enfants et ne permettre à

aucune personne n’étant pas familière avec un outil électrique ou son mode

d’emploi d’utiliser cet outil. Les outils électriques deviennent dangereux entre les mains

d’utilisateurs inexpérimentés.

e) Entretien des outils électriques. Vérifier si les pièces mobiles sont mal alignées ou

coincées, si des pièces sont brisées ou présentent toute autre condition susceptible

de nuire au bon fonctionnement de l’outil électrique. En cas de dommage, faire

réparer l’outil électrique avant toute nouvelle utilisation. Beaucoup d’accidents sont

causés par des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe bien

entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles à maîtriser.

g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux

présentes directives en tenant compte des conditions de travail et du travail à

effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour laquelle

il a été conçu est dangereuse.

5) RÉPARATION

a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant que

des pièces de rechange identiques. Cela permettra de maintenir une utilisation sécuritaire

de l’outil électrique.

Consignes de sécurité additionnelles propres aux marteaux

rotatifs

• Porter un dispositif de protection auditif. Le bruit en résultant pourrait occasionner une

perte de l’acuité auditive.

• Utiliser les poignées auxiliaires fournies avec l’outil. Une perte de contrôle de l’outil

pourrait occasionner des dommages corporels.

• Tenir l’outil par les surfaces isolées prévues à cet effet pendant toute utilisation où

l’organe de coupe pourrait entrer en contact avec des fils électriques cachés ou son

propre cordon. Tout contact avec un fil sous tension met les parties métalliques exposées de

l’outil sous tension et électrocute l’utilisateur.

• Utiliser des serre-joints, ou tout autre moyen, pour fixer et immobiliser le matériau sur

une surface stable. Tenir la pièce à la main ou contre son corps offre une stabilité insuffisante

qui pourrait vous en faire perdre le contrôle.

• Porter des lunettes de protection ou toute autre protection oculaire. Le martelage

pourrait faire voltiger des éclats. Ces particules volantes pourraient occasionner des dommages

oculaires permanents. Porter un masque anti-poussières ou un appareil de protection des voies

respiratoires pour toute application productrice de poussières. Une protection auditive peut

s’avérer nécessaire pour la plupart des applications.

• Maintenir systématiquement l’outil fermement. Ne pas tenter d’utiliser cet outil

sans le maintenir à deux mains. Il est recommandé d’utiliser systématiquement la poignée

latérale. Le fait d’utiliser cet outil à une main pourra vous en faire perdre le contrôle. Traverser ou

rencontrer des matériaux durs comme les armatures peut aussi s’avérer dangereux. Resserrer

soigneusement la poignée latérale avant toute utilisation.

• Ne pas utiliser l’outil pour mélanger ou pomper tout liquide facilement combustible ou explosif

(benzène, alcool, etc.).

• Ne pas mélanger ou remuer des liquides classifiés inflammables.

Product specificaties

Merk:	DeWalt
Categorie:	Boormachine
Model:	D25324K
Breedte:	329 mm
Hoogte:	225 mm
Stroombron:	AC
Input vermogen:	800 W
Boor diameter in staal (max):	13 mm
Boor diameter in beton (max):	26 mm
Boor diameter in hout (max):	30 mm
Aantal slagen:	4300 bpm
Aanslag-energie:	2.8 J
Gewicht (inclusief batterij):	3500 g
Nominale snelheid:	1150 RPM