Definitive Technology ProMount 90 Handleiding

Definitive Technology luidsprekersteun ProMount 90

Lees hieronder de 📖 handleiding in het Nederlandse voor Definitive Technology ProMount 90 (2 pagina's) in de categorie luidsprekersteun. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

The ProMount 90 is intended for use with Deﬁnitive Technology ProMonitor,

ProCenter, Mythos Gem and Gem XL loudspeakers or similar loudspeakers with

1/4-20 thread receptacles. Each bracket can support up to 10 lbs (4.5 kg). Do not

use a single bracket with any speaker weighing more than 10 lbs (4.5 kg). Use two

(2) ProMount 90 brackets with the ProCenter 1000 and ProCenter 2000.

Step 1

Loosen clamping screw with supplied Allen (hex)

wrench until ball pivot slides out. Be careful not

to fully remove the clamping hex screw.

Step 2

Fasten the ball pivot to the 1/4-20 threaded receptacle

on the back of the loudspeaker. Tighten the ball pivot

nut using a 7/16" (11 mm) wrench.

Step 3

1. Using the wall plate as a template, mark the two

screw-hole positions on the wall where you wish

to mount the bracket.

2. If you are certain that there is a stud behind

the wall surface, drive #10 wood screws

(not included) through the wall and into

the stud (a).

3. If there is no stud behind the wall at the

chosen location, install wall anchors (not

supplied) into the wall by following the

wall-anchor manufacturer’s instructions (b).

PROMOUNT 90 USER’S GUIDE

Installation

ball pivot

clamping screw

ball pivot

nut

For more information on Deﬁnitive Technology Loudspeakers and accessories,

visit www.deﬁnitivetech.com, or email info@deﬁnitivetech.com.

Deﬁnitive Technology, Owings Mills, Maryland, USA. 410-363-7148

4. Always use two wall anchors and two screws per

bracket. We do not provide mounting screws or other

hardware because we do not know to what kind of

material you will be attaching the speaker.

5. For wood surfaces and studs, use wood screws; for

sheetrock or gypsum, you should use wall anchors;

for masonry, use masonry anchors.

Step 4

1. Connect the speaker wires to the loudspeaker.

2. Place the ball pivot into the wall bracket clamp.

3. Hold the loudspeaker securely with one hand and

tighten the clamping screw until you feel friction

between the ball pivot and the clamp, but not so

tight as to prevent easy aiming of the speaker.

4. Adjust the speaker to the desired angle and tighten

the clamping screw ﬁrmly.

5. Do not over-tighten as that may strip the screw threads.

6. attempt to adjust the speaker angle while the clamping screw is tight. Do not

7. To adjust the loudspeaker angle, loosen the clamping screw, adjust the position

and re-tighten the clamping screw.

It is our pleasure to offer assistance if you have any questions regarding your

ProMount 90 or its set-up. Please contact your nearest Deﬁnitive Technology deal-

er or call us directly at (800) 228-7148 (US & Canada), 01 (410) 363-7148

(all other countries), or e-mail info@deﬁnitivetech.com.

Technical Assistance

Visit us at www.deﬁnitivetech.com.

Installation continued

PROMOUNT 90 USER’S GUIDE

EPAT100208

Product specificaties

Merk:	Definitive Technology
Categorie:	luidsprekersteun
Model:	ProMount 90
Kleur van het product:	Zwart
Gewicht:	3.73 kg
Plaatsing:	Muur
Compatibiliteit:	ProMonitor 1000 \r\nMythos Gem XL