Definitive Technology Mythos XTR-50 Handleiding

Definitive Technology Luidsprekers Mythos XTR-50

Lees hieronder de 📖 handleiding in het Nederlandse voor Definitive Technology Mythos XTR-50 (2 pagina's) in de categorie Luidsprekers. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Unpacking Your Mythos XTR-50 Speakers

Please Inspect For Shipping Damage

Each loudspeaker leaves our plant in perfect condition. Any visible or concealed

damage most likely occurred in handling after it left our plant and should be reported

at once to your Definitive dealer or the delivery company that delivered your loud-

speaker.Please unpack your speaker carefully.Save all cartons and packing materials in

case you move or need to ship your speaker. Record the serial number found on the

back of the Mythos XTR-50 on this manual.

VERY IMPORTANT: Accessories

Various parts and accessories that you will need to use your Mythos XTR-50 are in

the carton but areeasy to overlook. Open both ends of the shipping carton. Carefully

examine the contents of the shipping carton and packing material to find the plastic

bags with accessories.

Specifications

Mythos XTR-50

Driver complement: 2 each 3-1⁄2" (90mm) XTDD dome mid/bass drivers pressure-coupled

to 4 each 3-1⁄2" (90mm) dome low-bass radiators, 1 each 1" (25mm)

Pure Aluminum Dome Tweeter

Frequency response:(overall on wall) 92Hz – 30kHz; (+/- 3dB on wall) 120Hz – 20kHz

Sensitivity: 92dB

Impedance: 8 Ohms nominal

Dimensions: (mounted on wall without bracket) 27" H x 6" W x 1-1⁄2" D

(686mm x 152mm x 38mm)

Dimensions: (mounted on wall with bracket) 27" H x 6" W x 1-9⁄16" D

(686mm x 152mm x 40mm)

Dimensions: (on table stand) 30" H (762mm)

Table-stand base dimensions: 8-11/16" W x 4-3/4" D (222mm x 136mm)

Product Weight: 5.1 lbs. (2.3kg)

Specifications subject to change without notice.

Notes:

This product complies with the essential requirements

of the EMC directive 89/336/EEC.

FJAT12102009

MYTHOS XTR-50

OWNER’S MANUAL

Definitive Technology

For more information on Definitive Technology Loudspeakers and accessories,

visit www.definitivetech.com, or email info@definitivetech.com.

Definitive Technology, Owings Mills, Maryland, USA. 800-228-7148

MYTHOS XTR-50

OWNER’S MANUAL

Mythos XTR-50 Loudspeakers

Thank You

Thank you for choosing the Definitive Technology Mythos XTR-50 Loudspeaker

System. Our engineers spent many years developing this product. In order to ensure

that you experience the finest performance possible, we encourage you to take a

moment to fully read this owner’s manual and familiarize yourself with the proper

installation and set-up procedures for your Mythos XTR-50 speakers.

DEI Sales Co., dba Definitive Technology (herein “Definitive”) warrants to the original retail pur-

chaser onlythat this Definitiveloudspeakerproduct (the “Product”) will be free from defects in materi-

aland workmanship for a period of five (5) years covering the drivers and cabinets, and three (3) years

for the electronic components from the date of the original purchase from a Definitive Authorized

Dealer.If the Product is defectivein material or workmanship, Definitiveor its Authorized Dealer will,

at its option, repair or replace the warranted product at no additional charge, except as set forth below.

All replaced parts and Product(s) become the property of Definitive. Product that is repaired or

replaced under this warranty will be returned to you, within a reasonable time, freight collect. This

warranty is non-transferrable and is automatically void if the original purchaser sells or otherwise

transfers the Product to any other party.

This Warranty does not include service or parts to repair damage caused by accident, misuse, abuse,

negligence, inadequate packing or shipping procedures, commercial use, voltage in excess of the rated

maximum of the unit, cosmetic appearance of cabinetry not directly attributable to defects in material

or workmanship. This warranty does not cover the elimination of externally generated static or noise,

or the correction of antenna problems or weak reception. This warranty does not cover labor costs or

damageto the Product caused by installation or removal of the Product. Definitive Technology makes

no warranty with respect to its products purchased from dealers or outlets other than Definitive

Technology Authorized Dealer.

THE WARRANTY IS AUTOMATICALLY VOID IF:

1) The product has been damaged, altered in any way, mishandled during transportation, or tampered with.

2) The product is damaged due to accident, fire, flood, unreasonable use, misuse, abuse, customer

applied cleaners, failure to observe manufacturers warnings, neglect or related events.

3) Repair or modification of the Product has not been made or authorized by Definitive Technology.

4) The product has been improperly installed or used.

Product must be returned (insured and prepaid), together with the original dated proof of purchase to

the Authorized Dealer from whom the Product was purchased, or to the nearest Definitive factory

service center. Product must be shipped in the original shipping container or its equivalent. Definitive

is not responsible or liable for loss or damage to Product in transit.

THIS LIMITED WARRANTY IS THE ONLY EXPRESS WARRANTY THAT APPLIES TO YOUR

PRODUCT. DEFINITIVE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY

TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH

OUR PRODUCT OR THIS WARRANTY. ALL OTHER WARRANTIES, INCLUDING BUT NOT

LIMITED TO EXPRESS, IMPLIED,WARRANTY OF MERCHANTABILITY OR FITNESS FOR

A P

ARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED AND DISCLAIMED TO THE

MAXIMUM EXTENT ALLOWED BY LAW. ALL IMPLIED WARRANTIES ON PRODUCT ARE

LIMITED TO THE DURATION OF THIS EXPRESSED WARRANTY. DEFINITIVE HAS NO

LIABILITY FOR ACTS OF THIRD PARTIES. DEFINITIVE’S LIABILITY, WHETHER BASED

ON CONTRACT, TORT, STRICT LIABILITY, OR ANY OTHER THEORY, SHALL NOT

EXCEED THE PURCHASE PRICE OF THE PRODUCT FOR WHICH A CLAIM HAS BEEN

MADE. UNDER NO CIRCUMSTANCE WILL DEFINITIVE BEAR ANY LIABILITY FOR

INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. THE CONSUMER AGREES AND

CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND DEFINITIVE SHALL

BE RESOL

VED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY,

CALIFORNIA. DEFINITIVE RESERVES THE RIGHT TO MODIFY THIS WARRANTY STATE-

MENT A

TANY TIME.

Some states do not allowthe exclusion or limitation of consequential or incidental damages, or implied

warranties, so the above limitations may not apply to you. This warranty gives you specific legal rights,

and you may also have other rights which vary from state to state.

Limited Warranty: 5-Years for Drivers and Cabinets,

3-Years for Electronic Components

Mythos XTR-50 can be mounted either vertically as main or surround

speakers or horizontally for use as a center channel speaker. The logo

badge is not pre-attached to the

grille and is packaged in a plastic

bag along with the other

accessories. It should be affixed

in the correct place on the grille

once you have determined the

speaker’salignment. For horizontal

(center channel) use, align the badge

with the location on the long side of the

grille; for vertical use, align the badge with the

location on the short side of the grille. [Figure 11] To affix

the logo badge, gently press the logo badge into the recess

on the grill. A magnet will hold the logo in place. Do not press

the badge too hard or you may crack the grille.

Receiver/Speaker Set-up

Access your receiver’s “Speaker Set-up” or “Speaker Configuration” Menu.

1. In the Speaker Set-up/Configure function of your receiver, set all

channels that areconnected to Mythos XTR-50s to “Small.”

2. Select “Yes” when asked if you areusing a subwoofer.

3. Set the subwoofer crossover

frequency on the receiver to

120 Hz if the speaker is mounted

on a wall and 150 Hz if the

speakers aresitting on a shelf.

Service

Service and warranty work on your Definitive loudspeakers will normally

be performed by your Definitive Technology dealer or importer. If, however,

you wish to return the speaker to us, please contact us first, describing the

problem and requesting authorization as well as the location of the nearest

factory service center. Please note that the address given in this

booklet is the address of our offices only. Under no circumstances

should loudspeakers be shipped to our offices or returned

without contacting us first and obtaining return authorization.

Definitive Technology Offices

11433 Cronridge Drive, Owings Mills, Maryland 21117

Phone: (800) 228-7148 (US & Canada),

01 (410) 363-7148 (all other countries)

Technical Assistance

If you have any questions regarding your Mythos XTR-50 or its set-up,

please contact your Definitive Technology dealer or importer. If your

dealer or importer is unable to help you, please contact us directly at

(800) 228-7148 (US & Canada), 01 (410) 363-7148 (all other countries)

or e-mail info@definitivetech.com.

Attaching the Logo Badge

Figure 9

Figure 10

Figure 11

Definitive Technology

Connecting the Mythos XTR-50

The wire connection method used on the Mythos XTR-50 is

different than most speakers so please read these instructions!

(NOTE: if you are using the table stands, you should pass the wire through

the wire channels before attaching the green speaker wire connector.)

1. In the accessories plastic bag you will find a small green plastic

connector as shown in Figure 1.

2. Strip 1⁄2 inch (12 mm) of insulation from each conductor of the

speaker wire to expose the bare metal and twist each of the

individual conductors into single un-frayed strands.

3. Use a small jewelers screwdriver to loosen the screws on the

connector just enough to allow the wire ends to fit in

the holes. [Figure 1]

4. Slip the wire ends into the holes and tighten the screws until the

wire is firmly attached to the connector. (NOTE: if you are using

the table stands, you should pass the wire through the wire

channels before attaching the wire connector.)

Note that one of the terminals is marked

with “+” and the other is marked with “-“.

Make certain that you connect the wire

from the red (+) terminal of your amplifier

or receiver to the “+” terminal on your

speaker and the wire from the black (-)

terminal of your amplifier or receiver to the

“-“ terminal on your speaker. Most speaker

wirehas some indicator (such as color-

coding, ribbing or writing) on one of the

two conductors to help you maintain

consistency. It is essential to connect both

speakers to the amplifier in the same way

(in phase). If you experience a lack of bass

or poor surround effect, it is likely that one

or more of the channels is connected in

incorrect polarity and needs to be rewired.

Pay closer attention to connect

positive to positive and negative to

negative on all channels.

5. Gently push the male

connector with the wireinto

the female receptacle on the

speaker. The connector is

designed so that it can

only go in one way with the

correct orientation of positive

and negative pins. [Figure 2]

6. Connect a single RCA cable from the “SUB OUT” of your receiver

to the LFE input of the subwoofer (not included). [Figure 3] This

connecting method bypasses the subwoofer’sinternal “crossover”

or low pass filter and relies on the crossover filter built into

your receiver.

7. See page 4 for instructions on Speaker Set Up in your

surround receiver.

MYTHOS XTR-50

OWNER’S MANUAL

2 3

Wall Mounting the Mythos XTR-50

•We recommend that wall-mounting of speakers be performed by

professional installers or by those skilled in the use of power tools

and the knowledge of building codes and structural issues.

•We recommend that you determine a suitable location for your

speaker installation, and that you complete all wiring (especially

“hidden” in-wall wiring) before mounting the brackets to your walls.

•Mythos wall-mount brackets are not suitable for ceiling mounting.

The Mythos XTR-50 loudspeaker comes with a wall-mounting

bracket that can make mounting easier but in most cases the

bracket is not necessaryto wall-mount the speaker.The supplied

bracket may be necessary when mounting the speaker to a full-

motion or tilting TV wall-mount. You may choose to use the

supplied wall-mount bracket if you want the speaker to protrude a

bit more from the wall (total depth without the bracket is 1.5 inches

[38mm] and 1.6 inches [40mm] with the bracket). The bracket is

padded with foam that may be useful for damping rattles or

vibrations between speaker and wall surface.

Follow these directions for wall mounting the speaker without

using the bracket.

1. The supplied cardboard mounting template is double-sided; one

side is for horizontal orientation and the other is for vertical

mounting. Be sure to face the correct side toward you. Hold the

cardboard template in the intended location. Make sure

the speaker clears the ceiling, adjacent walls, corners, beams,

lighting fixtures and door/window frames. Leave at least 1" (25 mm)

above or to the side of the speaker location to allow the speaker to

slide onto the screws.

2. Make sure the center of the template is centered with the TV

screen’s center points.

3. When mounting the speaker horizontally,use a bubble level to

make sure the template is level.

When mounting the speaker vertically, use a plumb line to find

perfect vertical. If the TV is off-level or off-plumb, the speaker will

look better if it is off-level or plumb in exactly the same way as the TV.

5. Use push pins to securethe template to the wall.

6. Make pencil marks in the holes labeled “Pilot Hole (for mounting

without bracket)”; remove the template.

If you intend to place the Mythos XTR-50 on a TV or shelf

in a horizontal orientation, see page 3.

7. Pre-drill the pilot-hole locations for mounting screws (not included).

Use screws rated to hold securely in the wall material and have

screw heads (flat or panhead are acceptable) at least 0.33 inch

(8.5mm) in diameter.

8. It is best if at least one screw hits a wall stud.

If there is no stud behind the pilot-hole

location, install wall anchors (not included)

to secure the bracket screws. [Figure 5] Follow

the wall anchor manufacturer’s directions.

Each wall anchor should be rated to hold at

least one half of the product net weight

[see specifications on page 1].

9. For masonry walls, use a masonry drill bit to

pre-drill holes, and use masonry anchors and

screws (not included).

10. Drive in the screws until the head is approxi-

mately 0.12 inch (3mm) away from the wall.

If the screws are driven too close to the wall,

you will not be able to slip the speaker onto

the screw heads. If the screws are not close

enough to the wall, the speaker will be loose

and may rattle when played.

11. Push the speaker connector into the female receptacle on the back

of the speaker (see page 2).

12. Line up the speaker so that the screws enter the center part of the

+shaped channels; slide the speaker down so that the screw heads

hold the speaker in place. [Figure 4]

13. Gently pull on the speaker to make sure the screws are firmly

holding the speaker.

14. If the speaker is not held tightly to the wall, drive the screws in a

little deeper and try again.

Follow these directions for installing the speaker with the wall-

mounting bracket.

1. The supplied cardboard mounting template is double-sided; one

side is for horizontal orientation and the other is for vertical

mounting. Be sure to face the correct side toward you. Hold the

cardboard template in the intended location. Make sure

the speaker clears the ceiling, adjacent walls, corners, beams,

lighting fixtures and door/window frames. Leave at least 1" (25 mm)

above or to the side of the speaker location to allow the speaker to

slide onto the screws.

2. Make sure the center of the

template is centered with the TV

screen’s center points.

3. When mounting the speaker

horizontally, use a bubble level to

make surethe template is level.

When mounting the speaker vertically, use a plumb line to find

perfect vertical. If the TV is off-level or off-plumb, the speaker will

look better if it is off-level or plumb in exactly the same way as the TV.

5. Use push pins to secure the template to the wall.

6. Make pencil marks in the holes labeled “Pilot Hole”;

remove the template.

7. Pre-drill the pilot-hole locations for mounting screws (not included).

Use flat head screws rated to hold securely in the wall material and

have screws heads between 0.25 inch (6.4mm) and 0.33 inch

(8.4mm) in diameter.

8. It is best if at least one screw hits a wall stud. If

there is no stud behind the pilot-hole location,

install wall anchors (not included) to secure the

bracket screws. [Figure 5] Follow the wall anchor

manufacturer’s directions. Each wall anchor should

be rated to hold at least one half of the product net

weight [see specifications on page 1].

9. For masonry walls, use a masonry drill bit to

pre-drill holes, and use masonry anchors and

screws (not included).

10. Secure the bracket to the wall with screws driven

into the pilot holes or wall anchors. Bracket should

be tight to the wall, and screw heads should be

flush with the bracket.

11. Attach the supplied male connector to the speaker

wireand plug the connector into the receptacle on

the speaker (see page 2).

12. Line up the speaker so that the mounting heads enter the center

part of the + shaped channels; slide the speaker down so that the

mounting heads hold the speaker in place. [Figure6]

13. Gently pull on the speaker to make sure the screws are firmly

holding the speaker.

Mounting the Mythos XTR-50 to an

articulating TV bracket

If you have a Plasma or LCD TV that is attached to the wall via a

swing-out articulating bracket such as those offered by Chief and

Sanus, consult the TV bracket manufacturer’s user manual for

specific speaker mounting instructions.

Shelf/Table Mounting

If you are going to use the Mythos XTR-50 in horizontal mode on a

shelf or table, first attach the two supplied

rubber pads to the bottom edge of the speaker.

[Figure 7] Assemble the L-brackets to the

threaded holes in the back of the speaker using

the 1/4 20 x 12mm long screws provided.

[Figure8] Thread the foot screws into “L”

brackets and adjust to tilt the speaker up or down to aim

the speaker toward seated listener ear height.

If you aregoing to vertically mount the speaker on

a shelf or table, do not attach the wall mount

bracket to the speaker. Follow these steps:

1. Assemble the shelf stand using [Figure 9] as a guide.

2. Pass the speaker wire through the wire channel

and attach the male speaker connector to the

speaker wire as shown on Page 2.

3. Assemble the provided screw and square-neck nut onto the lower

hole in the back of stand leaving a 3mm gap between the nut

flange and the stand. [Figure10]

4. Line up the center of the + shaped channel with the square-neck

nut on the stand and push the speaker in and down on the nut.

5. Thread the provided 1/4 20 screw through the top hole in the

stand into the threaded hole in the speaker and tighten the screw.

MYTHOS XTR-50

OWNER’S MANUAL

Figure 1

Figure 2

Figure 3

Figure 5

Figure 4

Figure 6

Figure 7

Figure 8

Product specificaties

Merk:	Definitive Technology
Categorie:	Luidsprekers
Model:	Mythos XTR-50

Heb je hulp nodig?

Als je hulp nodig hebt met Definitive Technology Mythos XTR-50 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Luidsprekers Definitive Technology

Definitive Technology Mythos XTR-50 Handleiding

4 Oktober 2022

Handleiding Luidsprekers

Nieuwste handleidingen voor Luidsprekers

Dali Zensor Pico Vokal Handleiding

4 Oktober 2022

Intex IT-2616 SUF OS Handleiding

4 Oktober 2022

KEF Ci130.2CS Handleiding

4 Oktober 2022

Pioneer CS-3070 Handleiding

4 Oktober 2022

Nedis SPBT4100RD Handleiding

4 Oktober 2022

Thomson SB200BT Handleiding

4 Oktober 2022

Silvercrest SBLF 5 A1 Handleiding

4 Oktober 2022

Dali Opticon 8 Handleiding

4 Oktober 2022

JVC TH-WL311B Handleiding

4 Oktober 2022

Panasonic TY-SP50P8WK Handleiding

4 Oktober 2022