Deaf Bonce Apocalypse AAB-300.4D Atom Handleiding

Deaf Bonce Receiver Apocalypse AAB-300.4D Atom

Lees hieronder de 📖 handleiding in het Nederlandse voor Deaf Bonce Apocalypse AAB-300.4D Atom (24 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/24
HTTPS://ALPHARD.AUDIO
ATOM SERIES
FOUR-CHANNEL AMPLIFIERS
ЧЕТЫРЕХКАНАЛЬНЫЕ УСИЛИТЕЛИ
OWNER`S MANUAL
РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ
CLASS D
AAB-300.4D AAB- 00.4D 4
2
C O N T E N T S EN
1. Introduction
2. Safety instructions
3. Typical installation sequence
4. Selection of the diameter of power cables and speaker cables
5. Wiring diagrams
6. Connection methods
7. Specifications
8. Possible faults and their solutions
9. Box contents
10. Warranty and maintenance info
11. Information on disposal of the electrical and electronic equipment
( for the European countries with separate waste collection)
3
1 . I N T RO D U C T I O N
1. Make sure that your vehicle has a 12V DC electrical system with negative grounding. Before installing the amplifier in cars, trucks or
buses, check the battery voltage.
2. Check the state of on-board power supply of your vehicle, the battery and the alternator. When the engine is running, depending on
the ambient temperature, the voltage to be outputted by the alternator must be within the range of 14 to 14.7 V. Open circuit voltage
(OCV) of the battery must be within the range of 12.5 to 13 V. Make sure that the rated current of the alternator and the battery capacity is
enough to provide increased consumption.
For example, for the power of the amplifier 1000 W, the rated current of the alternator is required at the rate of 1000 W / 13 V = 77
amperes. A more powerful amplifier requires a more powerful alternator as well as an additional battery.
3. Do not place the amplifier in the engine compartment and also in the places exposed to water, moisture, dust or dirt.
4. Never stretch the cables outside of the car and near the moving parts of the car. This can lead to destruction of the insulating layer,
short circuit and fire.
5. The amplifier should be installed in areas of the car where the temperature varies from 0 °C (32 °F) to 55 °C (131 °F). The amplifier
should be in a place with a good air circulation. The horizontal position of the amplifier is the best way to install.
6. During the operation the amplifier may be heated up to 80 °C (176 °F). Before you touch it, make sure it is not overheated that may
be dangerous.
7. To improve the cooling of the amplifier, it is recommended to clean periodically the heatsink from dust. When cleaning the heatsink
strong solvents should not be used as they may damage the amplifier. Do not use compressed air, because solids can penetrate inside the
amplifier. Cleanings best done with wet towels or cloth.
8. Make sure that the location of the amplifier does not violate the proper operation of mechanical and electrical devices of the vehicle.
9. Make sure that during the installation and connection of the battery, the power cables are not shorted.
10. When performing plumbing, drilling or cutting works with the car, make sure that there is no wiring, brake lines, fuel pipe or other
structural elements under the place of work. Follow the safety rules! Use protective glasses and gloves.
11. To protect the wires use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies close to the
parts exposed to heat.
12. Make sure that all the cables are xed over the entire length. Also make sure that their outer protective shell is non-combustible.
Use a clamping screw to secure the positive and negative cables next to the appropriate terminals of the amplier.
13. Select a diameter of the power cable in accordance with the power of the amplifier and the recommendations provided here.
Power cables are extremely important since they directly affect the system damping factor and sound quality. The cables to the battery
must be in the copper crimp terminals pressed with the help of a hydraulic press, and well xed to the battery terminals.
14. To avoid accidental damage, keep the amplifier in its original packaging prior to installation.
15. Use high-quality copper speaker and power cables.
CAUTION!!! High sound pressure can damage your health!
Please use the common sense when controlling volume!
2 . S A F E T Y I N S T R U C T I O N S
3 . T Y P I C A L I N S TA L L AT I O N S E Q U E N C E
1. Before installing the amplifier disconnect the battery from the electrical system.
2. To connect the amplifier it is necessary to stretch the power cable from the location of the battery to the place of installation
of the amplifier. Select the power cable with the appropriate regulations in AWG (see Table: see Table: Selection of the diameter
of the power cables)
3. Connect the power supply with the correct polarity. Connect all (+) terminals of the amplifier to the cables stretching from
the positive terminal of the battery and all (-) terminals of the amplifier to the cables stretching from the negative terminal of the
battery.
4. Place the fuse holder for each positive cable within 40 cm from the positive terminal of the battery and connect one end of
the power cable to the holder after connecting the other end to the amplifier. Do not install the fuse(s).
5. Route all signal cables next to each other and separately from the power cables.
6. Connect the wires of RCA input. The input signal power must be between 0.2 VRMS and 6 VRMS.
7 To connect the power wire supply is necessary to use special. power cables.
8. Fasten the amplifier properly when installing it in the vehicle. If the component is disconnected during driving, it may cause
serious damage to the passengers of the vehicle or another vehicle. It is not recommended to screw the amplifier directly to the
metal it can lead to distorsions at the signal outputs.
9. After installation is complete, check the wiring of the system and make sure that all connections have been made correctly.
Before installing the fuses, disconnect the positive lead from the battery and then install the fuse in the fuse holder. Using the
light bulb 12 V 21 W, connect the positive lead to one contact of the bulb and the other contact of the bulb to the positive
terminal of the battery.
When properly connected, the bulb must briefly light up and go out. Now you may connect the positive lead to the (+) of the
battery. If the light does not go out, then something is wrong. This will prevent damage to the amplifier in case of reverse polarity
and unwanted sparks when connecting. Install the rest of the fuses.
10 . To activate the amplifier, it is necessary to apply the positive potential of 12 volts to the control input of the amplifier (REM)
through a switch or a corresponding control output (REMOTE OUT) with the head unit (HU).
11 LED indicator on front of the amplifier turns . blue to indicate that the amplifier is turned on. If the indicator does not light
up see chapter "Possible faults and their solutions" for more information.
12. The sound level is calibrated by adjusting the volume of the source up to 3/4 of its maximum level. Then, adjust the
sensitivity level of the amplifier up until you hear distortions.
Thank you for purchasing this Deaf Bonce product! Our company is committed to the creation of of extremely loud sound
systems with no loss of quality.
To ensure proper use, please carefully read through this manual before using this product. It is especially important that you
read and observe caution’s in this manual. Please keep the manual in a safe and accessible place for future reference.


Product specificaties

Merk: Deaf Bonce
Categorie: Receiver
Model: Apocalypse AAB-300.4D Atom

Heb je hulp nodig?

Als je hulp nodig hebt met Deaf Bonce Apocalypse AAB-300.4D Atom stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Deaf Bonce

Handleiding Receiver

Nieuwste handleidingen voor Receiver