Da-Lite Wireline Advantage 29875EG Handleiding

Da-Lite Niet gecategoriseerd Wireline Advantage 29875EG

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Wireline Advantage 29875EG (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

INSTRUCTION BOOK FOR

Wireline™ Advantage®

Tools Required for Installation

Important Safety Instructions

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so it will not be tripped over, pulled or contact

hot surfaces.

3. If an extension cord is necessary, a cord with a current rating at

least equal to that of the appliance should be used. Cords rated

for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric shock

when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of ire, electric shock, or injury to

persons.

6. Do not allow children to play with ixed controls. Keep remote

controls away from children.

7. Frequently examine the installation for imbalance and signs of

wear or damage to cables. Do not use if repair or adjustment is

necessary.

8. Appliance is not to be used by persons, including children, with

reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given

supervision or instruction.

9. Failure to provide adequate structural strength for this

component can result in serious personal injury or damage to

equipment! It is the installer’s responsibility to make sure the

structure to which this component is attached can support the

weight of all equipment. Reinforce the structure as required

before installing the component.

10. Use this projection screen only for its intended use as described

in these instructions. Do not use attachments not

recommended by the manufacturer.

Save These Instructions

1/4", 7/16" and 3/4“

Open Wrench or

Socket Driver

1/8“ Hex Key

(included)

Original Instructions

Disclaimer

Milestone and its ailiated corporations and subsidiaries

(collectively "Milestone"), intend to make this manual accurate

and complete. However, Milestone makes no claim that the

information contained herein covers all details, conditions or

variations, nor does it provide for every possible contingency in

connection with the installation or use of this subject to change

without notice or obligation of any kind. Milestone makes no

representation of warranty, expressed or implied, regarding the

information contained herein. Milestone assumes no

responsibility for accuracy, completeness or suiciency of the

information contained in this document.

Da-Lite® is a registered trademark of Milestone AV Technologies.

#3 Phillips

Screwdriver

1. The case provides multiple attachment Ceiling Mount:

points for bolts, cables, or threaded rod. Page 4 shows

threaded rod installed. The variable position-mounting

bracket may be located anywhere along the length of the

case. It is recommended to keep the brackets spaced evenly

enough to distribute the weight of the screen. One

mounting bracket is required for every 4' of case length.

Wall Mount: For use with optional langeless case only. The

variable position wall mounting brackets (sold separately)

may be located anywhere along the length of the case. It is

recommend to keep the brackets spaced evenly enough to

distribute the weight of the screen. One mounting bracket is

required for every 4' of case length.

2. Tighten bolts until trim lange is lush with Ceiling Mount:

ceiling.

Wall Mount: Remove lat brackets from top of case and

discard. Save bolts to attach wall brackets to case. Determine

spacing of wall brackets and attach to wall. Hoist screen to

brackets and completely tighten bolts attaching case to wall

brackets.

NOTE: For proper operation, screen assembly must be level

after installation.

3. Remove the silver shipping brackets that attach the slat to

the screen case. Use the supplied 1/8" hex key to remove the

set screws and a 1/4" socket to remove the screws from the

slat bar.

4. Using a 7/16" wrench and #3 Phillips screwdriver, remove the

shipping bracket that is attached to the roller. Once the

white wire is disconnected, feed it into the junction box in

order to complete the electrical installation. See Figure 1.

NOTE: Depending on the inal postion of the screen roller,

there may be a wood iller block insert for bracket

attachment. The wood block must be removed and

discarded before operation.

Case Installation

Pre-Installation

1. Carefully unpack case from shipping crate.

2. Set aside the Installation Kit. Items inside will be used during

installation.

3. Make sure to recheck measurement of case for proper

installation clearance.

4. Remove any protective foam from case.

5. If necessary, adjust hanger brackets with a 3/4" open wrench

or socket driver.

Remove

Bolt

White (Common)

Wire

Remove

Screw

Figure 1

Case Installation (continued)

5. Remove 2 screws to open junction box. Install electrical

connections that apply to your unit. Make sure to review the

wiring diagram for proper hook up. Replace junction box

cover and secure with 2 screws.

NOTE: Motor Operator Projection Screen Model WAD must

be installed in accordance with the requirements of the

Local Building Codes, the Canadian Electrical Code (CEC),

CAN/CSA C22.1 and the National Electric Code (NEC), NFPA

70. An appropriate disconnect device shall be provided as

part of the building installation.

6. Test installation by running screen up and down a few times.

Be prepared to stop screen should any objects obstruct the

movement of the screen. To prevent damage to the motor,

the standard duty cycle is 2 minute 30 seconds on and 50

minutes of. For 230 volt motors 2 operating cycles is not to

be exceeded.

NOTE: Do not allow upper batten bar to come to a rest on

any object during travel. Doing so will cause cables to lose

tension.

7. The screen comes set standard with 18" of wire drop out of

the case.

Wood

Filler

Block

Product specificaties

Merk:	Da-Lite
Categorie:	Niet gecategoriseerd
Model:	Wireline Advantage 29875EG

Heb je hulp nodig?

Als je hulp nodig hebt met Da-Lite Wireline Advantage 29875EG stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Da-Lite

Da-Lite Wireline Advantage 29745EG Handleiding

19 Juni 2023

Da-Lite The Providence 98143 Handleiding

19 Juni 2023

Da-Lite Da-Lift 19 78089WHT Handleiding

15 Juni 2023

Da-Lite Concord 98052 Handleiding

12 Juni 2023

Da-Lite Parallax 29838 Handleiding

11 Juni 2023

Da-Lite Flex Plex 29537 Handleiding

4 Juni 2023

Da-Lite Ascender Electrol 84764 Handleiding

3 Juni 2023

Da-Lite Lace And Grommet 92300 Handleiding

28 Mei 2023

Da-Lite Flex Plex 29532 Handleiding

25 Mei 2023

Da-Lite Cambridge 98166 Handleiding

16 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024

Kolcraft MLB New York Yankees Handleiding

26 November 2024

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024

Nedis POCO106 Handleiding

26 November 2024

Nedis BTSM1GY Handleiding

26 November 2024

Turbosound TPOLEAJ-01 Handleiding

26 November 2024

Turbosound TSTAND-01 Handleiding

26 November 2024

IFM TAD981 Handleiding

26 November 2024

IFM TAD961 Handleiding

26 November 2024