Da-Lite NET-100 Handleiding

Da-Lite Niet gecategoriseerd NET-100

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite NET-100 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

INSTALLATION GUIDE FOR

Da-Lite NET100

When connecting the NET100, there are three connections that

must be made to the SCB100 for proper operation: Power

+12Vdc, RS232 Communication and Ethernet.

NOTE: If you ordered your screen with a built-in SCB100 it will

come equipped with a 11-pin phoenix connector. The NET100 will

be equipped with a 2-pin plug and 3-pin plug for connection. The

2-pin plug will plug into #10 and #11 and the 3-pin plug will plug

into #4, #5 and #6. (See Fig. 1)

Product Description

The NET100 is an Ethernet adapter to the SCB100 Serial Control Board for Da-Lite motorized screens and projector lifts. This Ethernet

adapter allows remote control of a screen or lift through a TCP/IP connection.

The NET100 is classiied as a serial device server, which by deinition means that it makes available to client computers the Da-Lite

screen or lift as a serial device (enabled by the SCB100). The NET100 supports the suite of RS232 commands developed under the

SCB100, and allows those commands to be issued by an Ethernet enabled computer or third party controller.

Installation

Figure 1

Terminal

Block

3Pin Plug

RS232 Communication

2Pin Plug

+12VDC Output

If you did not order your screen with a built-in SCB100, remove the 2-pin and 3-pin connectors from the NET100. Refer to (Fig. 2)

Once these connections have been made and power

is supplied to the SCB100, the NET100 will be

powered from the SCB100.

Upon a successful connection, the power LED and

the status LED will turn on solid green. The green

10/100 Mb Link LED indicates the presence of

communication between the NET100 and

one or more nodes on the network.

Power II IPut

120VAC / 60Hz

Back Of

Wall Switch

Red (Tx)

Black (Rx)

Green (Ground)

Front Of

Wall Switch

NOTE: 2024AWG Wire

Recommended For Connecting

Wall Switch To The SCB100

Controller

RJ45 Connector

RJ45 Ethernet

Connection

Black With White

Stripe 12VDC+

Black Solid

12VDC -

DB25 to RJ45

Adaptor

Strain Relief

Black (Hot)

Green (Ground)

White (Common)

Black (Hot)

Green (Ground)

White (Common)

+ 120 VDC OUT

Red Up

Black (Down)

White (Common)

Red (Up)

Black (Down)

White (Common)

Rx - Data In

G - Ground

TX - Data Out

RX - Data In

G - Ground

Tx - Data Out

WBR

- 120 VDC OUT

Stop

Down

RJ45 PINOUT

PIN - 3 RX

PIN - 4 TX

PIN - 5 GR

PIN - 6 NOT USED

Figure 2

Coniguration

The NET100 is designed for simple, transparent installation and

coniguration. By default the NET100 is shipped with DHCP

disabled. The following IP address is assigned to the NET100.

IP Address: 192.168.1.100

Subnet: 255.255.255.0

To conigure the network settings, type the IP address into your

browser. It will open a new page with the setup proile. A new

window will pop up asking for a user name and password. Leave

the user name and password ield blank and press the OK

button.

The new window will contain the coniguration browser program.

The menu will be located on the left side of page. Click on

"Network".

For DHCP click on "Obtain IP address automatically" and type in

the DHCP HostName. For Static IP leave the option "Use the

following IP coniguration" clicked and type in the IP address and

Subnet Mask. Then click the "OK" button. Finally click on the

"Apply Settings" in the left menu.

Network Menu

OK Button

Blank

OK Button

Apply Settings

Product specificaties

Merk:	Da-Lite
Categorie:	Niet gecategoriseerd
Model:	NET-100
Kleur van het product:	Black, Grey
LED-indicatoren:	Ja
Aantal per verpakking:	1 stuk(s)
Aansluiting 1:	RS-232
Aansluiting 2:	RJ-45
Aansluiting 1 type:	Mannelijk
Aansluiting 2 type:	Vrouwelijk