Da-Lite Flex Plex 29535 Handleiding

Da-Lite Niet gecategoriseerd Flex Plex 29535

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Flex Plex 29535 (14 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/14
INSTRUCTION BOOK FOR
Polacoat Flex Plex Screen
2
Preparation
It requires at least four people to assemble a Flex Plex screen. To maintain optimal image geometry and screen alignment, a lat and
straight wall free from obstructions and angular distortions should be used. A wall opening with 5 + the ordered viewing height and
5+ the ordered viewing width must be used to maintain the precise in-wall it of the Flex Plex screen. When assembling the screen,
choose a clean work area using padded material or other soft, clean materials. The work area should be larger than the overall screen
size and directly in front of the wall opening where the screen is to be installed (audience side).
NOTE: Please read through the installation steps and note wait times. The rolled screen surface needs to be acclimated to the room for
48 hours prior to installation (Step 1). Once the surface is unrolled it will need to lay in its unrolled state for (Step 2).4 hours
Disclaimer
Milestone and its ailiated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete.
However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide
for every possible contingency in connection with the installation or use of this subject to change without notice or obligation of any
kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone
assumes no responsibility for accuracy, completeness or suiciency of the information contained in this document.
Da-Lite® is a registered trademark of Milestone AV Technologies. All rights reserved.
Installation Video
To view a video of this installation, visit https://youtu.be/45xbaYpXjd8.
Maintenance and Protection
Projection screens should always be installed after the
completion of construction, drywall, and painting of all adjacent
areas. If construction work needs to occur near an installed
screen, clean polyethylene sheeting should be used to cover and
protect both surfaces. Never apply adhesive tapes to the
coated surface. Always be careful to guard the screen against
damage from moving scafolding, ladders, or staging materials.
General Cleaning
Never use solvents on or near Da-Lite rear projection screens.
Remove dust by gently blotting the screen with a soft, clean, lint-
free cloth.
Dry Soil Marks
Clean with VM&P Naptha or with Da-Lite Lenskleen and a soft,
clean, lint-free cloth.
Cleaning of Frame and Trim
The exposed surfaces of the aluminum frames can be cleaned
with a dilute solution of detergent and water, followed by a clear
water rinse. Use a soft, grit-free cloth to preserve the anodized
inish. Protect screen surface during frame cleaning. Do not use
abrasive cleaners or solvents.
Tools Required for Installation (not provided)
Screw Gun/Drill and Drill Bits 1/2" Open Wrenches
(2) Ladders
#10 x 1 Countersunk
Flat Head Screws
¼ x 1” Hex Lag Screws1/8 & 3/16 Hex Keys
Measuring Tape LevelRubber Mallet
Knife
4
Included Parts and Hardware
N (3)
30’ Ropes
E (4) pairs
Gloves
C (2)
4 eces of Trim
A (1)
Screen Surface
Trim
H (2)
Hoisting Brackets
O (24)
Tensioning Assemblies
Frame PieRubber Gas
B
T-Tracks
D (3)
Lifting Brackets
I (4)
Cap Screws
NOTE: Quantities listed are for standard si tities will vary if a custom screen that is larger than standard is ordered.
Q (4)
Corner Covers
L (24)
3/8" x 1/2" Hex Head Screws
M (24)
3/8" Thin Hex Nut
K (4)
Corner Bracket
J (4)
Seam Bracket
6
Installation (continued)
4. While the screen is resting, the T-tracks (B) can be installed
into the wall opening. Measure 2½ from the side of your wall
opening to locate the end of the irst T-track (B) piece
(See Figure 1). Using one of the 4 pieces of trim (C), snap the
trim into place on one end of the T-track (B), place the T-track
in the opening and slide until the lower portion of the trim is
against the wall. Secure that end of the track with a #10 screw
in the hole closest to the end (See Figure 2).
Figure 1
2½"
NOTE: Most screen units will have one piece of T-track (B) for
the side openings and two pieces each for the top and
bottom wall openings. Larger sized units (above 14’ wide) may
have three pieces of T-track (B) each for the top and bottom
openings.
WARNING: Ensure each #10 countersunk screw head is
inserted completely and does not extend into the T-track
channel. If the screws are not inserted completely, the
screen tensioning assemblies will not slide through the
channel.
7
Step 4
Step 5
#10 Screw
4" Trim
Piece
T-track
5. Using the other 4” piece of trim (C) as a guide, secure the
opposite end of the T-track (B) section on the end hole with a
#10 screw. Once both ends are attached, slide the 4” trim (C)
pieces along the track to align the other positions and attach
a #10 screw into the hole openings until completed (See
Figure 2).
NOTE: Sliding the trim along the T-track (B) will maintain the
proper alignment when attaching the T-track (B) to the wall.
This alignment is necessary to allow the trim to snap on
easily at the end of the screen installation. Ensure the
opening is level on all four sides. If the opening is not level,
the T-track (B) will need to be shimmed in order to ensure the
screen trim is level once attached to the T-track (B).
Figure 2 Figure 3
Installation (continued)
6. Repeat Steps 4 and 5 until all T-track (B) sections have been
secured to the wall opening (See Figure 3). For top and
bottom sections, use 4 piece of trim (C) to overlap at the
seams as a guide to ensure that both T-track (B) pieces are
lush with each other in the wall opening.
9
10. At the unrolled screen surface (A), peel back the protective
paper approximately 3/4on the top and the bottom. This will
allow the frame to be attached easily to the screen surface.
NOTE: Do not remove the protective paper completely. This
will be done at the end of the screen installation in order to
protect the surface during the hanging process.
Da-Lite recommends that the provided gloves (E) be worn at
this time in order to prevent damage to the screen surface and
to provide grip while lifting.
11. Center the irst rubber gasket (F) on the screen surface edge
and press it into place starting at one end. Repeat this step
for the three remaining sides of the screen.
12. Place the frame sections (G) around the screen surface (A).
Attach to frame (G) over the rubber gasket (F) with set screws
facing upwards. Use a rubber mallet to gently tap the screen
frame into place if needed (See Figure 5)
Installation (continued)
13. Place the hoisting bracket (H) in the center of the top and
bottom sections of the screen frame. Attach to frame using
the provided cap screws (I) and a 3/16” hex key.
14. Starting from the center on each side, tighten all set screws
on all four sides of the frame using the 1/8 hex key.
Approximately two threads should be visible on each set
screw when properly tightened.
15. Prepare to attach the seam brackets (J) and corner brackets
(K) by carefully sliding the 3/8" x 1/2" hex head screws (L)
down the frame channel (two bolts on either side of the seam
and two on each side of each corner).
16. Carefully slide the seam bracket (J) under the assembled
frame, aligning the bracket and 3/8" screws (L) across the
seam. Secure using the 3/8" thin hex nuts (M) and tighten
completely.
17. Repeat for corner brackets (K).
Figure 5
Hoisting Bracket
Hoisting Bracket
Pre-Attached
Hoisting Brackets
Frame
Section
Rubber Gasket
Frame
Section
Hoisting Bracket
Rubber Gasket
Set Screw
Cap
Screw
Screen
(Projector Side)
Seam Bracket
Seam Bracket
Corner Brackets
11
Installation (continued)
21. Raise the screen assembly into the wall opening. On the
projector side, one person will remain holding all three ropes
(N) without slack, guiding the screen into place. On the
audience side, two people will lift the screen vertically, one on
the left and one on the right side. These three people (one
rope control and two lifters) will coordinate together to lift the
screen into place. The fourth person should be on a ladder on
the projector side helping the rope control and lifters guide
the screen assembly into place until all three hoisting and
lifting brackets attach to each other at the top of the wall
opening (See Figure 8).
Figure 8
T-Track
2"
Lifting Bracket
Hoisting
Bracket
Screen Assembly
(Audience Side)
22. Once the screen is hanging on the hoisting and lifting
brackets, carefully remove the seam (J) and corner (K)
brackets along with the 3/8" screws (L) and nuts (M).
NOTE: During this step, be careful not to touch the projection
coating on the audience facing side of the screen assembly
along the screen edges.
NOTE: At the end of this step, the screen assembly’s weight
should be supported by the hoisting and lifting brackets and
it should be centered side to side inside of the wall opening.
Gloves can be removed at this time.


Product specificaties

Merk: Da-Lite
Categorie: Niet gecategoriseerd
Model: Flex Plex 29535

Heb je hulp nodig?

Als je hulp nodig hebt met Da-Lite Flex Plex 29535 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Da-Lite

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd