CyberPower BP240VL3U01 Handleiding

CyberPower Niet gecategoriseerd BP240VL3U01

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower BP240VL3U01 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1













1. Switch EBM DC breaker to the ON position.

2. Switch the utility circuit breaker feeding the UPS

to the ON position.

3. Turn the UPS ON – push and hold the ON/OFF

power button for 3 seconds; you will hear

continuous beeps, the BATTERY ON yellow

LED will ﬁrst turn on for a couple of seconds

followed by the ON-LINE green LED.

4. Customize UPS system conﬁguration settings as

needed. See User’s Manual for complete details.

User Manual is available to download on

www.CyberPowerSystems.com.

5. Connect equipment load to the UPS system.

1. Install rack mount ears to the extended battery

module (EBM) using eight black M5X7L ﬂat head

screws. Install hanging brackets using six silver

M5X6L pan head screws.

2. Locate the space where the extended battery

module will be installed in the rack.

3. Install the rackmount rails using eight black

M5X12L pan head screws with plastic washers

and adjust the rails to the necessary rack depth.

4. Place the extended battery module on to the

rackmount rails. Make sure both left and right

hanging brackets are securely on the rackmount

rails. Secure the extended battery module with

the rack mount ears to the rack using four black

M5X12L pan head screws.

BP240VL3U01/ BP240VL3U02

QUICK START GUIDE

K01-0000704-00

UNPACKING

RACKMOUNT INSTALLATION

TOWER INSTALLATION

CONNECTING UPS TO

EXTENDED BATTERY MODULE

CONNECTING UPS TO MULTIPLE

EXTENDED BATTERY MODULES

EXTERNAL BATTERY MODULE CONFIGURATION

POWER ON THE UPS SYSTEM

1. Turn o the DC breaker on the EBM.

2. Loosen the two screws to remove the battery

cable retention bracket of the power module.

3. Use the output cable of the EBM to connect it

to the power module.

4. Rotate the battery cable retention bracket

and tighten the two screws to secure the

battery connector.

5. Turn on the DC breaker on the EBM.

1. Connect the 1st EBM to the UPS power module

following the “Connecting UPS to Extended Bat-

tery Module” instructions.

2. Turn o the DC breaker of the 2nd EBM.

3. Loosen the two screws to remove the battery

cable retention bracket of the 1st EBM.

4. Use the output cable of the 2nd EBM to con-

nect it to the 1st EBM. Rotate the battery cable

retention bracket and tighten the two screws to

secure the battery connector.

5. Turn on the DC breaker on the 2nd EBM.

6. Proceed to the External Battery Module

Conﬁguration instructions to set the EBM

Number to the quantity of additional units

installed with the UPS system. This operation

can also be done if there is an RMCARD

installed in the UPS, or via PowerPanel®

Business Edition Agent software. Please see

their respective User’s Manuals for instructions.

1. Adhere four circular rubber pads to the left hand

side of the extended battery module. This will

become the bottom side.

2. Stand the extended battery module on its

side with the rubber pads facing down. Install

dust covers on open screw holes. If installing

the extended battery module together with a

UPS or an additional EBM secure the tie plate

between the two using four black M5X7L ﬂat

head screws. Optionally adhere four circular

rubber pads to each rack mount ear to use as

tower stands. Screw the tower stands on to the

EBM and UPS using four black M5X12L pan head

screws for added stability as shown below.

3 41 Rack mount ear

Rack mount rail

This document is believed to be accurate, but CyberPower reserves the right to change or correct the contents and does not

Reproduction in whole or in part without permission is prohibited.

Need Additional Help? Feel free to contact our Tech Support department with installation, troubleshooting,

or general product questions.

CyberPower Technical Support | 1-877-297-6937 | tech@cpsww.com | www.CyberPowerSystems.com

Mailing Address: 4241 12th Avenue E, Suite 400, Shakopee, MN 55379, USA

Hours of Operation: Monday–Friday, 7:00am–6:00pm (CST)

IEC320 C14 TO IEC320 C13

POWER CORD RT GUIDE x1

LEFT & RIGHT RACKMOUNT

RAILS x1 EACH

LEFT & RIGHT HANGING

BRACKETS x1 EACH

3U RACKMOUNT EARS

(TOWER STANDS) x2

TOWER INSTALLATION

TIE PLATE x1

M5X7L BLACK FLAT

HEAD SCREWS x8

M5X12L BLACK PAN

HEAD SCREWS x12

QUICK START GUIDE x1REGISTRATION CARD x2EXTENDED BATTERY

MODULE (EBM) x1

M5X6L SILVER PAN

HEAD SCREWS x6

PLASTIC WASHERS x8SCREW HOLE DUST

COVERS x14

RUBBER PADS x12

CAUTION! Installation environment should be in a temperature and humidity controlled indoor area free of conductive

contaminants. Do not install this EBM where excessive moisture or heat is present (Please see speciﬁcations for acceptable

temperature and humidity range).

CAUTION! Never install an EBM, or associated wiring or equipment, during a lightning storm.

CAUTION! Do not work alone under hazardous conditions.

CAUTION! Risk of electric shock, do not remove top cover.

CAUTION! The battery can energize hazardous live parts inside even when the AC input power is disconnected.

CAUTION! Only use replacement batteries which are certiﬁed by Cyber Power Systems. Use of incorrect battery type is an electrical

hazard that could lead to explosion, ﬁre, electric shock, or short circuit.

CAUTION! Batteries contain an electrical charge that can cause severe burns. Before servicing batteries, please remove any

conductive materials such as jewelry, chains, wrist watches, and rings.

CAUTION! Do not open or mutilate the batteries. Electrolyte ﬂuid is harmful to the skin/eyes and may be toxic.

CAUTION! To avoid electric shock, turn o and unplug the EBM from the wall receptacle (if installed) before servicing the battery.

CAUTION! Only use tools with insulated handles. Do not lay tools or metal parts on top of the UPS or battery terminals.

CAUTION! To prevent the risk of ﬁre or electric shock, only use the supplied hardware to attach the mounting brackets.

OFF

External Battery Modules can be conﬁgured by the

user to display correct estimated battery runtimes.

1. Press the “ ” button to activate the ENTER

“MAIN MENU.”

2. Press the “p” and “ ” buttons to scroll to the q

“Conﬁgure” menu.

3. Press the “ENTER” button to select the

“Conﬁgure” menu.

4. Press the “p” and “ ” buttons to scroll to the q

“EBM Number” option.

5. Press the “ ” button to select the ENTER

“EBM Number” option.

The ﬁrst conﬁguration number will be displayed

on the second column of LCD display.

6. Press the “p” and “ ” buttons to scroll through q

the number of attached Battery modules.

NOTE: The ﬁrst EBM is recognized by the UPS

system as number zero “0”. Set the EBM Number

to the quantity of additional units installed with

the UPS system.

7. Press the “ ” button to select the number ENTER

of EBM installed.

You will be prompted to save the selection.

Press the “ENTER” button to save.

8. Press the “ ” button to cancel or return ESC

to the previous LCD menu.

IMPORTANT SAFETY INSTRUCTIONS

This Quick Start Guide contains important instructions. Please read and follow all instructions carefully

during the installation and operation of the unit. Read this Quick Start Guide thoroughly before

attempting to unpack, install, or operate this unit.

PLUG INTO A

WALL

RECEPTACLE

RELA Y

OUT PUT

OUT

USB

RS23 2

BACK -FEED PROT ECTI ON

CON NECT OR

BATT ERY INPU T : 240V

EPO

IN TERF ACE

FU SE

250V~

10A

AC INPU T

(Cha rge Only )

AC OUTP UT

240V

BATT ERY OUTPU T

BATT ERY INPU T

240V

OUT PUT BREAKE R

30A/250V~

OUT PUT BREAKE R

30A/250V~

NON CRI TICA L

LOAD

CR ITIC AL LOA D43

IN PUT BREAKER

63A / 250V~









































































































CONFIGURE SUBMENU AVAILABLE SETTINGS DEFAULT SETTINGS

EBM Number

= [0] [1] [2] [3] [4] [5] [6] [7] [8] [9] [10]

Sets the quantity of EBM (extended

battery modules) number to get the

correct estimated runtime.



  







1 2

OFF

Product specificaties

Merk:	CyberPower
Categorie:	Niet gecategoriseerd
Model:	BP240VL3U01
Kleur van het product:	Zwart
Gewicht:	76000 g
Breedte:	433 mm
Diepte:	660 mm
Hoogte:	132 mm
Accu/Batterij voltage:	12 V
Certificering:	UL 1778\nCSA C22.2 NO.107.3-05\nFCC Part 15 Class A
Duurzaamheidscertificaten:	RoHS
Accu/Batterij oplaadtijd:	4 uur
Temperatuur bij opslag:	-20 - 45 °C
Luchtvochtigheid bij opslag:	0 - 95 procent
Aantal inbegrepen batterijen:	20 stuk(s)
Hoogte, in bedrijf:	0 - 3000 m
Hoogte bij opslag:	0 - 15000 m
Compatibiliteit:	OL6KRT, OL6KRTF, OL8KRT, OL8KRTF, OL10KRT, OL10KRTF, OL10KRTHW
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Hot-swap batterij:	Ja