Cuisinart HM200T Handleiding

Cuisinart Niet gecategoriseerd HM200T

Lees hieronder de 📖 handleiding in het Nederlandse voor Cuisinart HM200T (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
RANDOM
ORBITAL
SANDER
230W
ORIGINAL INSTRUCTIONS
SPECIFICATIONS
Motor: 230W
No Load Speed: 12,000/min
Disc Size: 125mm (5”)
Paper Fitment: Hook and Loop
Power Cord: 2m
Weight: 2kg
ROS-2000U
WHAT’S IN THE BOX
Random Orbital Sander
Sandpaper Sheet
Dust Bag
MAINTENANCE
DESCRIPTION OF SYMBOLS
TROUBLE SHOOTING
V Hz
~ W
ø
/min
n
o
Volts
Alternating current
Revolutions or
reciprocation per minute
Double insulated
Warning
Hertz
Watts
No load speed
Diameter
• Keep the ventilation vents of the drill clean at all times, if possible, prevent
foreign matter from entering the vents.
• After each use, blow air through the drill housing to ensure it is free from all
dust particles which may build up. Build up of dust particles may cause the
drill to overheat and fail.
• If the housing of the sander requires cleaning, do not use solvents but a moist
soft cloth only. Never let any liquid get inside the housing; never immerse any
part of the sander into liquid.
Replacing the Hook & Loop Backing Pad
After considerable use, the hook and loop backing pad (2) surface will
become worn, and must be replaced when it no longer offers a rm grip. The
replacement backing pad can be ordered through the Special Orders Desk at
any Bunnings store.
1. To replace, remove the four philips head screws by rotating anti-clockwise.
2. Place new backing pad on the tool and retighten the four philips head
screws by rotating clockwise.
Note: Ozito Industries will not be responsible for any damage or injuries
caused by the repair of the tool by an unauthorised person or by mishandling
of the tool.
Sparking visible through the housing air vents
A small amount of sparking may be visible through the housing vents.
This is normal and does not indicate a problem.
Excessive sparking visible through the housing air vents
and/or the sander failing to operate
May indicate the carbon brushes have worn out and need to be replaced. Carbon
brushes should only be replaced by a qualied electrician or power tool repairer.
Sandpaper Selection
Selecting the correct grit of sandpaper is an important step in achieving
optimum results. Coarse grit will remove the most material. Finer grit will
produce a smoother nish. The condition of the workpiece will determine the
grit of the sandpaper to be used. The higher the grit number, the ner the
grade of sandpaper.
If the surface is rough, start with a coarse grit and sand until the surface is
uniform. Medium grit may then be used to remove scratches left by the coarser
grit. Finer grit is then used to nish the surface. Always continue sanding with
each grade of sandpaper until the surface is uniform.
MATERIAL APPROPRIATE GRIT
Coarse Sanding Fine Sanding
Paintwork 180 400
Wood: Softwood 60 240
Hardwood 60 180
Veneer 240 320
Note: If intermediate sanding is required, choose a grit rating between coarse and
ne. The above table is intended as a guide only. To ensure a satisfactory result,
a small, inconspicuous area should rst be tested to ensure the grit of sandpaper
chosen is suitable for the desired nish.
Sanding Tips
Never force the sander. The weight of the sander supplies adequate pressure,
allowing the sandpaper to do the work. Applying additional pressure will slow the
motor, rapidly wear the sandpaper, and greatly reduce the sander speed. This will
slow the removal rate and produce an inferior quality surface.
CAUTION: Excessive pressure will overload the motor, causing possible damage
to the sander by overheating the motor; or damage to the workpiece.
Be sure to check your workpiece often. The sander is capable of removing
material rapidly, especially with coarse paper.
The orbital action of your sander allows you to sand with the grain, or at any angle
across it for most sanding jobs. In the nal stages a better nish will be achieved
by sanding with the grain.
Do not sand on one spot for too long. The sander’s rapid action may remove too
much material, creating an uneven surface.
SPARE PARTS
ozito-diy.co.uk
RANDOM ORBITAL SANDER SAFETY WARNINGS
Read Instruction Manual
WARNING! When using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of re, electric shock, personal injury
and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before
operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
Before you connect the equipment to the mains supply make sure that the data on the rating plate are
identical to the mains data.
This tool is double insulated therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid
a hazard.
Note: Double insulation does not take the place of normal safety precautions when operating this tool. The
insulation system is for added protection against injury resulting from a possible electrical insulation failure
within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not
suitable for the power input of the tool or which is damaged or defective may result in a risk of re and electric
shock.
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the
warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power
tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching
outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your
nger on the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualied repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
GENERAL POWER TOOL SAFETY WARNINGS
ELECTRICAL SAFETY
WARNING!
• Hold power tool by insulated gripping surfaces, because the sanding pad
may contact its own cord. Cutting a “live” wire may make exposed metal parts of
the power tool “live” and could give the operator an electric shock.
Recommendation that the tool always be supplied via a residual current device
with a rated residual current of 30 mA or less.
Unplug the sander before changing accessories. Accidental start-ups may occur if
the sander is plugged in while changing an accessory.
Disposing of dust. Be extremely careful of dust disposal, materials in ne particle
form may be explosive. Do not throw sanding dust on an open re. Spontaneous
combustion, may in time, result from a mixture of oil or water with dust particles.
Always wear eye protection and a dust mask for dusty applications and when
sanding overhead. Sanding particles can be absorbed by your eyes and inhaled
easily and may cause health complications.
Use special precautions when sanding chemically pressure treated timber,
paint that may be lead based, or any other materials that may contain
carcinogens. A suitable breathing respirator and protective clothing must be worn
by all persons entering the work area. Work should be sealed by plastic sheeting and
persons not protected should be kept out until work area is thoroughly cleaned.
Do not ‘wet sand’ with this sander. Liquids entering the motor housing are an
electrical shock hazard.
Do not use sandpaper intended for larger sanding pads. Larger sandpaper will
extend beyond the sanding pad causing snagging, tearing of the paper or kick-back.
Extra paper extending beyond the sanding pad can also cause serious lacerations.
WARNING!
Some dust created by power sanding, sawing, grinding, drilling and other
construction activities contain chemicals known to cause cancer, birth defects or other
reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints;
• Crystalline silica from bricks, cement and other masonry products, and;
• Arsenic and chromium from chemically-treated timber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area and
work with approved safety equipment, such as dust masks that are specially designed
to lter out microscopic particles.
WARRANTY
OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG 0616
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the customer
service number shown. Please note the following terms under which
guarantee claims can be made:
1. These warranty terms regulate additional warranty services, which the
manufacturer mentioned below promises to buyers of its new products
in addition to their statutory guarantee claims are not affected by this
guarantee. Our guarantee is free of charge to you.
2. The warranty services only covers defects due to material or
manufacturing faults on a product which you have bought from the
manufacturer mentioned below are limited to either the rectication of said
defects on the product or the replacement of the product, whichever we
prefer.
Please note that our devices are not designed for use in commercial, trade
or professional applications. A guarantee contract will not be created if the
device has been used by commercial, trade or industrial business or has
been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly
instructions or due to incorrect installation, a failure to follow the operating
instructions (for example connecting it to an incorrect mains voltage or
current type) or a failure to follow the maintenance and safety instructions
or by exposing the device to abnormal environmental conditions or by lack
of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example
overloading the device or the use or unapproved tools or accessories),
ingress of foreign bodies into the device (such as sand, stones or dust,
transport damage), the use of force or damage caused by external forces
(for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural
wear or tear or by normal use of the device.
4. Your Product is guaranteed for a period of 36 months from the original
date of purchase and is intended for DIY (Do It Yourself) use only. Lithium
Ion batteries and chargers are covered by a 12 month warranty. Warranty
excludes consumable parts. Guarantee claims should be submitted
before the end of the guarantee period within two weeks of the defect
being noticed. No guarantee claims will be accepted after the end of the
guarantee period. The original guarantee period remains applicable to the
device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts tted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work
performed or parts tted. This also applies if an on-site service is used.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR
REGISTER RECEIPT.
Please refer to the restrictions of this warranty concerning wearing parts,
consumables and missing parts as set out in the service information in
these operating instructions.
CUSTOMER SERVICE HELPLINE
GB: 0151 294 4488
IRL: 1850 882711
Ozito-diy.co.uk
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse or Homebase store.
For further information, or any parts visit
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: enquires@ozito-diy.co.uk
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1. Connect the tool to the mains power supply.
Side to Side
KNOW YOUR PRODUCT
ROS-2000U
1. HOOK AND LOOP SANDING SHEET 2. DUST BAG 3. ON/OFF SWITCH 4.
SANDING
1. When placing the sheet, align the holes on the sanding sheet with
the holes on the sanding pad. 2. To turn on, press the on/off switch to the “I” position.
3. To turn off, press the on/off switch to the “0” position.
2. To remove, pull
the dust bag away
from the extraction
port.
1. Push the dust
bag onto the dust
extraction port
aligning the locking
tab and rotate as
shown.
5. Dust Bag 6. Hook & Loop Sanding Sheet
ACCESSORIES
1 On/Off Switch
2 Hook & Loop Backing Pad
3 Soft Grip
4 Dust Bag Adaptor
RANDOM ORBITAL SANDER
SETUP & PREPARATION OPERATION
Install
2. Replace the sanding sheet when it is worn.
3. Replace hook &
loop backing pad
when worn (see
maintenance section).
The tool is recommended for use with a residual current
device with a rated residual current of 30mA or less.
1/3
Backward/ Forward
3. Empty dust bag when it becomes
1/3 full for optimum dust
extraction.
CAUTION: GUIDE THE CORD DURING SANDING TO
PREVENT IT BEING CAUGHT ON THE WORKPIECE,
OR OTHER OBJECTS.
Remove
2. Firmly grasp the sander
and switch it on. Let
the motor build up to
maximum speed.
3. Gradually lower onto the
workpiece with a slight
forward movement.
4. For optimum results, use either of these stroke patterns.
1. Secure the material to be sanded..
Ensure the tool is disconnected from the power supply before
performing any of the following operations.
Empty

Product specificaties

Merk: Cuisinart
Categorie: Niet gecategoriseerd
Model: HM200T

Heb je hulp nodig?

Als je hulp nodig hebt met Cuisinart HM200T stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Cuisinart

Cuisinart

Cuisinart AMB-9SPBZ Handleiding

16 November 2024
Cuisinart

Cuisinart AMB-9SCKBZ Handleiding

16 November 2024
Cuisinart

Cuisinart AMB-12MP Handleiding

16 November 2024
Cuisinart

Cuisinart AMB-9SPCH Handleiding

16 November 2024
Cuisinart

Cuisinart AMB-CR2 Handleiding

16 November 2024
Cuisinart

Cuisinart FCT3545-24 Handleiding

16 November 2024
Cuisinart

Cuisinart AMB-6MTPCH Handleiding

16 November 2024
Cuisinart

Cuisinart AMB-6 Handleiding

16 November 2024
Cuisinart

Cuisinart CPT-200 Handleiding

23 Oktober 2024
Cuisinart

Cuisinart CRBW-33 Handleiding

8 Juli 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic

Panasonic NB-W250 Handleiding

25 November 2024
Alpine

Alpine CHM-S611 Handleiding

25 November 2024
AOpen

AOpen DE3650-C Handleiding

25 November 2024
Lazer

Lazer Urbanize MIPS Handleiding

25 November 2024
Symmons

Symmons Dia 353GB-24 Handleiding

25 November 2024
SoundTube

SoundTube IPD-RS62-EZ Handleiding

25 November 2024
Moen

Moen Camerist 4905 Handleiding

25 November 2024
Lazer

Lazer Cameleon DLX Handleiding

25 November 2024
DMT

DMT DLD-85 Handleiding

25 November 2024
AOpen

AOpen AM1120T Handleiding

25 November 2024