CTA Digital PAD-CGS Handleiding

CTA Digital Niet gecategoriseerd PAD-CGS

Lees hieronder de 📖 handleiding in het Nederlandse voor CTA Digital PAD-CGS (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

PAD-CGS

2. Base Assembly and Connecting the Metal Cover:

METAL CONNECTION

HEIGHT

ADJUSTMENT

KNOB

POLE

METAL

CROSS BASE X 2

CONNECTION SCREW BOLT,

WASHERS AND NUT

Pole Assembly and Pole Nut

Cross Base Sections (2)

Medium

Allen Key

Use this table to determine the appropriate

foam pad to use with your tablet.

Note: sizes refer to total tablet size with

or without a case.

Foam Pad

Thickness

Tablet

Thickness:

1mm 0.67-1.06in

5mm 0.51-0.91in

10mm 0.31-0.71in

17-27mm

13-23mm

8-18mm

Select the appropriate foam pad according to

the thickness of your tablet (or tablet in its

case), then press adhesive side into center

of the tablet holder.

10mm

Foam

Pad

Attaching Foam Pad to Tablet Holder

1mm Foam Pad

Instructions:

1. Installing the Wheels

Wheel

Place a spring washer over the screw

bolt on the wheel.

Place the screw bolt from each wheel through the metal base, then place a nut cover

over the top of each. Screw down clockwise by hand, then use wrench to tighten

further.

Screw Nut Cover

Spring

Washer

Metal

Base

5mm

Foam

Pad

Gooseneck flexes by hand.To adjust the height of the pole,

turn plastic cover counter-clockwise and raise or lower the pole

to desired height. Turn clockwise again to lock it in place.

3. Adjustment:

Biggest

Allen Key

360 rotation

o270 rotation

Multi

direction

flexing

Use the biggest Allen key to tighten and loosen the

gooseneck connection screw, adjusting ease of

rotation in the tablet holder.

3. Connecting the Battery Case and Tablet Holder and Installing Your Device

4.Press button on side of tablet holder to

slide open. Insert your tablet against

spring arm,then slide other end back

down.

Gooseneck

Metal

Connection

Battery Case

Smaller

Allen Key

1. Place battery case over top of metal connection.

2. Screw gooseneck down onto metal connection by turning clockwise.

3. Use smaller Allen key to tighten the small meter screw inside

gooseneck.

Note: if meter screws are already in, unscrew before attaching gooseneck.

1) Place the metal base pieces with the higher

piece on top of the cross base. Align the holes

at the bottom of the pole with the holes on the

cross base.

2) Insert a screw bolt with a washer into each

of 4 holes. Place another washer on the

underside of each screw bolts.

3) Grip the nut on the underside with one hand,

and use the other to tighten each screw with

Medium Allen key. Repeat to tighten all four

screw bolts.

4. Rotate the grip counter clockwise to

loosen completely and remove from top

of pole.

5. Place the square metal cover over

the top of the pole and slide down to

stand base.

6. Place grip back over stand pole

and tighten.

Product specificaties

Merk:	CTA Digital
Categorie:	Niet gecategoriseerd
Model:	PAD-CGS
Kleur van het product:	Zwart
Gewicht:	4712.8 g
Breedte:	444.5 mm
Diepte:	444.5 mm
Max. hoogte van de standaard:	1473.2 mm
Maximale schermgrootte:	13 "
Minimale schermgrootte:	7 "
kantel aanpassingen:	Ja