Crystorama Clover CLO-8000-AG Handleiding

Crystorama Lamp Clover CLO-8000-AG

Lees hieronder de 📖 handleiding in het Nederlandse voor Crystorama Clover CLO-8000-AG (2 pagina's) in de categorie Lamp. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
How to Install
All electrical components must be
installed by a licensed electrician
in accordance with the National
Electric Code and the appropriate
local electrical codes.
WARNING: This product can expose you to Lead,
which is known to the State of California to cause cancer
and/or birth defects or reproductive harm. For more
information go to www.P65Warnings.ca.gov
®
ASSEMBLY INSTRUCTION MODEL #CLO-8000-AG
3.Screw the lower rod and center stem onto the top of
wiring box.
52″
32.6″
48″
48″
CRYSTAL SETS:
U.Ø16mmx26,Ø60mmx1
W.Ø40mmx188,Crystal ball with long thread
Ø40mmx188,Crystal ball
U:
W:
4.Slide the center ring over the lower rods and center stem
and secure the center ring with hex nut and check ring.
5.Screw the upper rods onto the center.
8.Insert each long threaded crystal ball through the
bottom of the ring,then secure it from the top with the
crystal ball (without nipple).
Installation of safety cable
1.Pass the long threaded pipe on the hickey through the
center of outlet box.Attach it to the ceiling joist and
secure it with nuts.
2.Feed wires and safety cable up through chain and the
hole of screw collar loop.Have the wires and safety
cable exit through the side of hickey.
3.Feed safety cable through the cable lock and coil it
around the hickey twice.Then feed the cable through
the lock again and tighten it with lock screw.
4.Continue to run safety cable through the top of outlet
box and secure it to the ceiling joist.
2.Put the check ring over the hex nut on top of wiring box.
6.Place the top metal plate over the upper rods and secure
it with hex nuts.
7.Pull the wire from center stem through the hickey until
taut and put the top cap over it and secure with xture
loop.
1.Remove X (Flat tube) and Y (Rod) by twisting the screws
with a screwdriver
Part Number
Part Numbers
PART NUMBER MODEL #CLO-8000-AG
A.Mounting Hardware
(3)Wire Nut
(1)Hickey
(2)1/4" IP NIPPLE
(4)Nut
(4)Flat Washer
(4)Spring Washer
E
J
K
R
S
T
W
U
V
B.(1)Canopy;Ø5.5″x0.98″h;XMO8890AGCAN5.5IN
D.(1)Chain;72″Lx Ø6.0mmT;XMO8000AGCHA6.0MM
E.(1)Top Loop
J.(4)Upper rod;Ø0.5″x13.4″h;XMO8000AGRODU13.4IN
K.(1)Center Stem;Ø0.75″x23.8″h;XMO8000AGSTEM23.8IN
R.(8)Arm;Ø0.5″
S.(1)Metal ring
T.(2)Bottom ring
U.(1)Strand Crystal
V.(24)Candle Sleeve;Ø1 ″x2.8″h;XMO8890AGCDL2.8IN
W.(376)Crystal Ball;Ø1.57″
A
B
CD
C.(2)Quick Link
P
O
O.(4)Lower rod;Ø0.5″x9.5″h;XMO8000AGRODL9.5IN
Q
L
MN
G
HI
G.(4)Hex Nut
H.(4)Washer
I.(1)Top Metal Plate
F
F.(1)Top Cap
L.(4)Check Ring
M.(4)Hex Nut
N.(1)Center Ring
P.(4)Check Ring
Q.(4)Hex Nut
Y
X
X.(4)Flat tube
Y.(4)Rod;Ø0.5″x21.5″h


Product specificaties

Merk: Crystorama
Categorie: Lamp
Model: Clover CLO-8000-AG

Heb je hulp nodig?

Als je hulp nodig hebt met Crystorama Clover CLO-8000-AG stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Lamp Crystorama

Handleiding Lamp

Nieuwste handleidingen voor Lamp