CRU DE50 Handleiding

CRU Cradle/docking station DE50

Lees hieronder de 📖 handleiding in het Nederlandse voor CRU DE50 (2 pagina's) in de categorie Cradle/docking station. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Rugged, Reliable, Mobile, SecureTM

1-800-260-9800 www.CRU-DataPort.com

DE50 IDE Install Guide

Removable Ultra ATA 100 Drive Enclosure

NOTE: For Ultra ATA100 (100MByte/sec) operation, an Ultra ATA100 control-

ler and hard drive(s), and appropriate 40-pin, 80-conductor cable are required.

Drive Carrier Installation

1. Loosen and remove the four (4) M3 Phillips Flat Hd. screws located on

the sides of the drive carrier unit. Save these screws for Step 6.

2. Since the drive carrier unit is shipped pre-assembled, disassemble the

drive carrier unit into its three (3) main components (Figure 1).

3. Install the Drive Carrier Circuit Board (cable-side down) onto the drive

by attaching the I/O cable on the board to the drive.

4. Set Master/Slave drive designation. There are two ways to set the

Master/Slave drive designation for the DE50 unit, as described below.

NOTE: The information below is based on typical drive speciﬁcations.

Since speciﬁcations (speciﬁcally, pin assignments) between drive

manufacturers may vary, please refer to your drive manufacturer’s

documentation for information regarding Master/Slave conﬁguration.

Cable Select Method (Recommended Method)

In most cases, there is no need to reconﬁgure the jumper on JMP1 located

on the rear of the drive carrier circuit board. A factory-installed jumper on

Pins B & D forces the drive into a Cable Select conﬁguration (Figure 2).

With Cable Selection, the Master/Slave Drive designation is handled by

the Master/Slave Selection Jumper Option (J2) on the receiving frame

motherboard. If necessary, reconﬁgure jumper (factory-conﬁgured jumper

is for Master Drive designation). Skip section “Drive Select Method” and

continue with Step 5 of the Installation process.

Top

Cover

Drive Mounting

Bracket/Bottom

Plate Assembly

Drive Carrier

Circuit Board

Drive Select Method

In most cases, this method forces the drive into either a Master or Slave

Drive conﬁguration. This method will override any conﬁguration of the Mas-

ter/Slave Selection Jumper Option (J2) on the receiving frame motherboard.

The J2 jumper option is instead used to conﬁgure the unit ID display.

Master Drive

Remove the jumper from JMP1. Typically, no jumper installed on JMP1

forces the carrier into a Master Drive conﬁguration (Figure 2).

Leave the J2 jumper option (on the receiving frame motherboard) as is for

Master Drive ID display purposes (factory-conﬁgured jumper is for Master

Drive designation).

Slave Drive

Install the jumper on JMP1 Pins C & D (Figure 2). Typically, a jumper

installed on Pins C & D forces the drive into a Slave Drive conﬁguration

(refer to the drive manufacturer’s documentation for exact master/slave

jumper settings and reconﬁgure the jumper as necessary).

Conﬁgure the J2 jumper option for Slave Drive ID display purposes.

5. Carefully turn the drive/circuit board assembly upside-down (drive is

bottom-mounted into bracket). Install the drive mounting bracket and

secure with four (4) M3 screws (provided).

NOTE: Make sure that the drive circuit board is properly seated in

the mounting bracket slot before tightening screws.

6. Carefully insert the drive/bracket assembly into the top cover and

secure with the four (4) M3 screws (saved from Step 1).

Figure 1: Drive Carrier Disassembly

Figure 2: Drive Carrier Circuit Board

I/O Connector

Recommended

Conﬁguration

Typical Master Drive

Conﬁguration

No Jumper

Installed

Typical Slave Drive

Conﬁguration

Jumper Installed

on Pins C & D

Cable Select

Conﬁguration

Jumper Installed

on Pins B & D

(Factory Default)

Rugged, Reliable, Mobile, SecureTM

1-800-260-9800 www.CRU-DataPort.com

Master/Slave J2 Jumper Option on the Receiving Frame Mother-

board (Figure 3)

Master/Slave Selection Jumper (J2)

Master Drive conﬁguration (Factory Default). Change jumper position to set

Slave Drive conﬁguration.

Forces master/slave drive conﬁguration on the receiving frame if JMP1

jumper option (located on the drive carrier circuit board) is conﬁgured to

Cable Select.

If using the Drive Select Method, this option is instead used to conﬁgure

the unit ID display (refer to Figure 4 for further information).

For 5.25” peripheral slots, the 5.25” adapter bracket must be installed. The

receiving frame is side-mounted into the adapter bracket using four (4) M3

Phillips Pan Head screws (provided).

With the drive carrier locked in place inside the receiving frame, install the

DE50 into the 5.25” drive opening in the computer or expansion chassis.

Use the appropriate guides to position the DE50 unit, and fasten it into

place with four (4) self-tapping screws (included). Mounting holes are pro-

vided on each side and the bottom of the adapter bracket to accommodate

a variety of mounting conﬁgurations. Use the mounting holes which best

suit the computer or expansion chassis conﬁguration.

Unit ID Select Switches Settings

The following table lists the unit ID select switch settings and the valid AT/

IDE unit numbers. Please note that all invalid switch settings have shaded

boxes and result in a blank display in the receiving frame window.

NOTE: The unit ID number display is for ID display purposes only (when

using the Drive Select Method). The master/slave setting must still be set

on the DE50 unit itself (refer to Page 1 for further information).

Selecting the Unit ID Number

Use the alignment tool (provided) to select the ID number of the disk drive.

NOTE: The lock on the Data Express receiving frame functions as a

lock and a DC power switch for the carrier unit. The lock MUST be

engaged (turned counterclockwise) in order to supply power to the

carrier and installed drive unit.

Limited Product Warranty

CRU-DataPort (CRU) warrants the Data Express DE50 to be free of signiﬁ-

cant defects in material and workmanship for a period of three years from

the original date of purchase. CRU’s warranty is nontransferable and is

limited to the original purchaser.

Limitation of Liability

The warranties set forth in this agreement replace all other warranties. CRU

expressly disclaims all other warranties, including but not limited to, the

implied warranties of merchantability and ﬁtness for a particular purpose

and non-infringement of third-party rights with respect to the documen-

tation and hardware. No CRU dealer, agent or employee is authorized to

make any modiﬁcation, extension, or addition to this warranty. In no event

will CRU or its suppliers be liable for any costs of procurement of substi-

tute products or services, lost proﬁts, loss of information or data, computer

malfunction, or any other special, indirect, consequential, or incidental dam-

ages arising in any way out of the sale of, use of, or inability to use any CRU

product or service, even if CRU has been advised of the possibility of such

damages. In no case shall CRU’s liability exceed the actual money paid for

the products at issue. CRU reserves the right to make modiﬁcations and

additions to this product without notice or taking on additional liability.

Certiﬁcation

EMI Standard: FCC Part 15 Class B, CE

EMC Standard: EN55022, EN55024

FCC Certiﬁcation

This device has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received; including interfer-

ence that may cause undesired operation.

A7-050-0001 Rev 2.1

Figure 3: Receiving Frame

Motherboard (rear view)

Figure 5: Unit ID Select Switch Location

I/O

Connector

Master Drive Select (0)

(Factory Default)

Slave Drive

Select (1)

5.25” Adapter Bracket

(shown installed)

Key Lock &

Power Switch

Eject Button

Unit ID Select

Switch Location Unit ID Number

Indicator

Figure 4: Unit ID Select Switch Settings

J2 DC Power

Connector

= Pin1

Activity Indicator

Unit ID Select

Position 0 1 2 3 4 5 6 7 8 9

Unit ID Select

Position XMas-

ter Slave X X Mas-

ter Slave XXX

Unit ID Number

Display Blank 0 1 Blank Blank 2 4 Blank Blank Blank

Product specificaties

Merk:	CRU
Categorie:	Cradle/docking station
Model:	DE50
Kleur van het product:	Zwart
Breedte:	102 mm
Diepte:	144 mm
Hoogte:	26 mm
LED-indicatoren:	Ja
Aantal USB 2.0-poorten:	2
Certificering:	RoHS
Opslagmedia-type:	HDD
Output current:	1 A
Standaard interfaces:	USB 2.0
Opslag schijf-interface:	Parallel ATA (IDE)
Aantal storage drives ondersteund:	1
Opslagschijf afmetingen ondersteund:	2.5 "
Hot-swap:	Ja