Crestron HDI-TX-301-C-2G-E Handleiding

Crestron AV extender HDI-TX-301-C-2G-E

Lees hieronder de 📖 handleiding in het Nederlandse voor Crestron HDI-TX-301-C-2G-E (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

DO GUIDE

HDI-TX-301-C-2G-E

DM Lite Multiformat Switch and Transmitter, International

Installation into a European Electrical Box

Installation into a UK Electrical Box

DO Install the Device

Install the device in a 2-gang European or UK electrical box (not included). A minimum mounting

depth of 45 mm is required.

To install the device:

1. On the rear of the device, make connections to the TO RX and Ethernet ports.

NOTES:

• For the 24 Vdc power connection, connect a power pack to either the transmitter or

a compatible receiver. Do not connect a power pack to both devices simultaneously.

Power is transmitted over the cable that connects the TO RX port on the transmitter to

the FROM RX port on the receiver.

A power pack is not included with the transmitter. When the transmitter is used with a

DM Lite surface-mount receiver, the transmitter receives power from the power pack

that ships with and connects to the receiver.

• Cabling that connects the TO RX port to the FROM TX port is designed for

intrabuilding use only.

Rear View

2. Using a Phillips screwdriver, do either of the following:

• Attach the transmitter to a European electrical box using the four included

M3 x 15 mm Phillips at head screws.

• Attach the transmitter to a UK electrical box using the two included M3.5 x 30 mm

Phillips at head screws.

3. Position a Crestron decorator-style faceplate (sold separately) over the front panel of the

transmitter, and then gently press down on the faceplate until it snaps into place.

DO Check the Box

QTY ITEM PART NUM.

4 Screw, M3 x 15 mm, Flat Head, Phillips* 2052287

2 Screw, M3.5 x 30 mm, Flat Head, Phillips†2052288

*For installation into a European electrical box

†For installation into a UK electrical box

24 G

TO RX:

To FROM TX

link input of

receiver

Passive

pass-through

to front panel

Ethernet port

24 V

1.25 A:

From power pack

(not included)

DO GUIDE DOC. 8330A (2052057) 07.18

Specications subject t o change without not ice.

DO Connect the Device

Connect the front of the device as required for the application.

Front View

The SERVICE port, which is located on the bottom of the transmitter, is for factory use only.

Bottom View

DO Congure the Device

To congure the device, do either of the following:

• If the transmitter connects to an HD-RX-201-C-E, congure the transmitter using the

web interface of the HD-RX-201-C-E. The HD-RX-201-C-E hosts the conguration of the

transmitter.

To access the web interface, open a web browser and then go to the IP address of the

HD-RX-201-C-E. By default, DHCP is enabled. To display the IP address on the connected

HDMI® display, press the button on the front panel of the HD-RX-201-C-E. SETUP

Pressing the SETUP button on the transmitter will also display the IP address of the

HD-RX-201-C-E.

To log in to the web interface, enter the user name and password. The default user name

and password are both admin.

• If the transmitter does not connect to an HD-RX-201-C-E, refer to Answer ID 1000168

in the Online Help section of the Crestron website (www.crestron.com/onlinehelp) for

conguration information.

NOTE: When the transmitter does not connect to the HD-RX-201-C-E, pressing the

SETUP button on the transmitter has no effect.

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The specic patents t hat cover Crestron products are listed at .

www.crestron.com/legal/patents

The product warranty can be found at .www.crestron.com/legal/sales-terms-conditions-warranties

Certain Crestron products contain open source software. For specic information, visit . www.crestron.com/ legal/open-source-sof t ware

Crestron and the Crestron logo are either trademarks or regist ered trademarks of Crestron Elect ronics, Inc., in the Unit ed St ates and/or other countries. HDMI and t he HDMI logo are either

trademarks or registered trademarks of HDMI Licensing LLC in t he United States and/or ot her count ries. Ot her t rademarks, registered trademarks, and trade names may be used in this

document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary int erest in the marks and names of others. Crestron is not responsible

for errors in t ypography or photography.