Crestron DM-TX-4K-202-C Handleiding

Crestron AV extender DM-TX-4K-202-C

Lees hieronder de 📖 handleiding in het Nederlandse voor Crestron DM-TX-4K-202-C (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

DO GUIDE

DO Connect the Device

Connect the device as required for the application.

Connections, Left Side (DM-TX-4K-302-C Shown)

Connections, Right Side

NOTE: The DM OUT port of the DM-TX-4K-302-C is a PoDM+ powered device (PD) port and is also

compatible with HDBaseT® PoE+. The DM OUT port of the DM-TX-4K-202-C is a standard PoDM

PD port and is also compatible with HDBaseT PoE. In order for the device to receive PoDM+ or

PoDM, the device requires connection to a DigitalMedia™ switcher or other equipment that has a

corresponding PoDM+ or PoDM power sourcing equipment (PSE) port. In order for the device to

receive HDBaseT PoE+ or HDBaseT PoE, the device requires connection to equipment that has a

corresponding HDBaseT PoE+ or HDBaseT PoE PSE port. Any wiring that is connected to a PoDM+,

PoDM, HDBaseT PoE+, or HDBaseT PoE PSE port is for intrabuilding use only and should not be

connected to a line that runs outside of the building in which the PSE is located.

Connection to the included power pack is not required when PoDM+, PoDM, HDBaseT PoE+, or

HDBaseT PoE is used to power the device.

NOTE: The DM-TX-4K-302-C requires PoDM+, HDBaseT PoE+, or the included power pack to power

a USB device that connects to the USB HID port. PoDM, HDBaseT PoE, or the included power pack

can be used to power the DM-TX-4K-302-C if no USB device connects to the USB HID port.

DM-TX-4K-202-C/DM-TX-4K-302-C

4K DigitalMedia 8G+® Transmitters

DO Install the Device

The Crestron® DM-TX-4K-202-C and DM-TX-4K-302-C can be mounted onto a at surface or onto a

rack rail.

Mounting onto a Flat Surface

Using four mounting screws (not included), mount the device onto a at surface such as a wall or a

ceiling.

Mounting onto a Wall

Mounting onto a Rack Rail

The DM-TX-4K-202-C and DM-TX-4K-302-C mount onto the front or rear rail of a rack. Position either

the left or the right mounting ange of the device so that the holes align with the holes in the rack.

Then, secure the device to the rack using two rack mounting screws (not included).

Mounting onto a Rack Rail

DO Check the Box

QTY PRODUCT PART NUM.

1 Connector, 2-Pin 2003574

1 Connector, 5-Pin 2003577

1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2045865

HDMI IN 1–2:

From HDMI®

audio/video

sources

AUDIO IN:

From unbalanced

stereo line level

audio source*

DM OUT:

To DM® switcher,

receiver, or other

DM device or to

HDBaseT® device

VGA IN:

From RGB (VGA),

component, S-video,

or composite

video source*

24 V

0.75A:

From included

power pack

Ground

*VGA IN and AUDIO IN are available on the DM-TX-4K-302-C only.

COMPUTER:

To computer

or other USB

HID compliant

host

HDMI OUT:

To HDMI

display

IR:

To IR

controllable

device

LAN:

10BASE-T/

100BASE-TX

Ethernet to

local network

device

COM:

RS-232

device

USB HID:

To mouse/

keyboard or

other USB HID

compliant device

DO GUIDE DOC. 7743E (2044941) 01.18

Specications subject to change without not ice.

For the DM-TX-4K-202-C, PoDM, HDBaseT PoE, or the included power pack can be used to power a

USB device that connects to the USB HID port.

NOTE: The LAN port can connect to an Ethernet switch only if the DM OUT port does not connect to

a DigitalMedia switcher.

For information about VGA IN, DM OUT, and LAN connector pin assignments, refer to the following

illustrations and tables.

VGA IN Connector Pin Assignments (DM-TX-4K-302-C Only)

DM OUT Connector Wiring

LAN Connector Pin Assignments

DO Set the IP Address

The conguration of the transmitter within the DigitalMedia 8G+

® system determines how the IP

address of the transmitter is set:

• If the transmitter connects to a DigitalMedia switcher, the transmitter is congured by the

switcher automatically.

• If the transmitter connects to a DigitalMedia 8G+ receiver, the transmitter uses its own

conguration settings. By default, DHCP (Dynamic Host Conguration Protocol) is enabled.

If assignment of the default IP address to the transmitter is desired, hold down the SETUP

button while the unit boots up. The default IP address overwrites the current setting.

The default IP address of the DM-TX-4K-202-C is 192.168.1.204. The default IP address

of the DM-TX-4K-302-C is 192.168.1.205. To manually set a different IP address, use

Crestron Toolbox™ software.

DO Learn More

Visit the website for additional information and the latest rmware

updates. To learn more about this product, use a QR reader

application on your mobile device to scan the QR images.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

This product is Listed to applicable UL

® Standards and requirements tested by Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

This unit is for indoor use only. It is not intended for outdoor use.

Cet appareil est réservé à une utilisation en intérieur. Il n’est pas destiné à une utilisation en extérieur.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The specic patents t hat cover Crestron products are listed at .www.crestron.com/legal/patents

The product warrant y can be found at .www.crestron.com/legal/sales-terms-conditions-warranties

Cert ain Crestron products cont ain open source soft ware. For s pecic informat ion, visit . www.crestron.com/legal/open-source-soft ware

Crest ron, t he Crestron logo, Crest ron Toolbox, Digit alMedia, Digit alMedia 8G+, and DM are either t rademarks or registered trademarks of Crest ron Electronics, Inc. in the United Stat es and/

or ot her count ries. HDBaseT and the HDBaseT Alliance logo are either t rademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI and t he

HDMI logo are either t rademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are either trademarks or regist ered trademarks

of Underwriters Laboratories, Inc. in t he United States and/or ot her countries. Other t rademarks, registered trademarks, and trade names may be used in this document to refer to either t he

ent ities claiming t he marks and names or their products. Crest ron disclaims any proprietary interest in t he marks and names of others. Crestron is not responsible f or errors in t ypography or

photography.

This document was writ ten by the Technical Publications depart ment at Crest ron.

DM-TX-4K-202-C DM-TX-4K-302-C

Pin 1Pin 8

NUM. WIRE COLOR PIN

NUM. WIRE COLOR

1 Orange/White 5 Blue/White

2 6Orange Green

3 7Green/White Brown/White

4 8Blue Brown

Pin 1

Pin 8

PIN NUM. PIN NUM.SIGNAL SIGNAL

1 5TX+ N/C

2 6TX- RX-

3 7RX+ N/C

4 8N/C N/C

PIN NUM. RGB YPbPr S-VIDEO COMPOSITE

1 R CPr

2 G Y Y

3 B Pb COMP

5 GND GND GND GND

6 RED_GND C_GNDPr_GND

7 GRN_GND Y_GND Y_GND

8 BLU_GND Pb_GND

13 H

14 V

NOTE: For best video performance, ground connections should

be kept separate. Do not connect ground wires to the connector

shell. The connector shell is reserved for the cable shield.

Pin 10

Pin 5 Pin 1

Pin 6

Pin 15 Pin 11

Product specificaties

Merk:	Crestron
Categorie:	AV extender
Model:	DM-TX-4K-202-C
Kleur van het product:	Zwart
Gewicht:	647 g
Breedte:	135 mm
Diepte:	28 mm
Hoogte:	280 mm
Soort:	AV-zender
LED-indicatoren:	Ja
USB-connectortype:	USB Type-A, USB Type-B
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Ondersteunde video-modi:	1080p, 2160p
Maximum resolutie:	4096 x 2160 Pixels
Aantal USB-aansluitingen:	2
HDCP:	Ja
Aansluiting voor netstroomadapter:	Ja
Materiaal:	Metaal
Ondersteunde grafische resoluties:	1600 x 1200 (UXGA),1920 x 1080 (HD 1080),1920 x 1200 (WUXGA),2048 x 1080,2560 x 1440,2560 x 1600 (WQXGA),3840 x 2160,4096 x 2160
Netwerkstandaard:	IEEE 802.3at
Output current:	0.75 A
HDMI in:	2
Aantal HDMI-uitgangen:	1
RJ-45 invoer ports:	1
Operating voltage:	24 V
HDBaseT-poort:	Ja
Maximaal bereik:	100 m
AC-ingangsspanning:	100-240 V
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
HDCP- & EDID-omzeiling:	Ja