Crest Audio CPX 3 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Crest Audio CPX 3 (18 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/18
www.crestaudio.com
Operating
Manual
6
16
20
23
26
29
32
6
16
20 23
26
29
32
TMTM
6
16
20
23
26
29
32
6
16
20 23
26
29
32
TMTM
6
16
20
23
26
29
32
6
16
20 23
26
29
32
TMTM
FCC/ICES Compliancy Statement
This device subject device complies with Part is 15 of the FCC. Operation to the conditions: following two (1) this may
not interference cause cause accept any harmful interference, and (2) this device must received, that may undesired
operation.
Le présent aux Canada appareil conforme est CNR d’lndustrie applicables aux radio de appareils exempts
licence. L’exploitation est autorisée aux doit de deux conditions suivantes: (1) I’appareil ne pas produire
brouillage, et même (2) a brouillage I’utilisateur de I’appareil doit ccepter tout radioélectrique subi, s i le
brouillage est d’ f susceptible en compromettre le onctionnement.
Warning: Changes or to modifications the equipment not approved by Crest Audio can void the user’s
authority quipment. to use the e
Note – This equipment been for A has t toested and found comply with the limits a Class digital device,
pursuant to 15 Part of provide the FCC limits designed rules. These are to reasonable protection against
harmful interference environment. when the perated in a equipment is o commercial This equipment
generates, i uses and can radiate radio frequency energy and, if not nstalled and use in accordance with thed
instruction manual, peration of this n may cause harmful to interference radio communications. O equipment i
a residential area ill be is likely to cause harmfu in the userl interference which case w required to correct the
interference at their expense.
Meridian, MS 05 393 (601) 5 483-536 FAX 01) -1 8 (6 486 27
ENGLISH
INTRODUCTION
Congratulations! You have just one of the finest The CPX amplifier features a two-purchased world’s professional power amplifiers.
way crossover and sub-sonic (low-cut) filter for each channel. Crossover frequencies are fixed at 150 Hz, to be allowing subwoofers
driven at extremely high sound pressure levels, and the filters cut at 40 Hz to prevent low-end rumble. Using proven technology
gained through years of amplifier design, this unit takes of rugged TO-3P output devices mounted on massive aluminum advantage
extrusions and dissipates heat via an extremely quiet and effective fan. CPX are designed to operate at line two-speed amplifiers
voltages as low as 50% of nominal, mammoth transformers and offering impressive and employing toroidal power specifications
features not found on similarly competitive This amp is to drive a 2 Ohm load per channel, priced units. designed s thus achieving
awesome performance levels into 4 Ohms in BRIDGE mode. CPX are ruggedly constructed, rack-mountable pieces of gear amplifiers
with superb patching capability, Front allowing superior flexibility in application. panel features include detented gain (dB) calibrated,
controls and LED indicators for power Thermal Protection indicator, and GCLâ„¢ activation on each (PWR), signal presence (SIG),
channel, as as a rocker mains POWER The back contains an IEC connector, line voltage selector switch, dual well switch. panel
primary fuses, and the critical cooling This opening have an adequate supply of cool air and should never be fan opening. should
blocked or Also on the back panel are the input and output sections, including an input barrier strip for permanent restricted.
installations. Each channel input section includes combo XLR / TRS jack connector, THRU/LOW out and HIGH out TRS a phone
jacks, and activation switches for the LOW filter and crossover (150 Hz output sections feature dual shock-CUT XOVER). Channel
proof posts and four-conductor twist lock connectors. binding An additional four-conductor twist lock connector allows mode BRIDGE
output.
UNPACKING
Inspect the amplifier during unpacking. If any damage is found, notify your dealer immediately. Be sure to save the carton and all
packing materials. Should you ever need to ship the unit back to Crest Audio®, one of its service centers, or the dealer; use only the
original factory packing.
INSTALLATION
CPX power amplifiers are designed for durability in commercial and provide quality professional installations the performance required
in studio and home applications. are two-rack-space units of 1 " ( mm) depth designed to mount in a standard 19" They 5.5 380 rack.
Rear mounting ears are provided for additional The minimum depth from the surface is support. rack required mounting
17" (432 mm) to allow connector clearance.adequate
BASIC SETUP
Before mounting, make sure the voltage selector is set to the voltage (page ).line correct 5
Rack mount the amplifier in the where it is to be used, remembering to allow for adequate access and cooling space. Make location
all the to the desired connectors on the Select the proper mode connections INPUT desired channel. configuration (STEREO or
BRIDGE). Connect speakers to the desired OUTPUT connectors.
Make sure the load impedance greater than 2 per channel to prevent the from shutting down. is Ohms (4 Ohms bridged) amplifier
With the POWER switch OFF, connect the IEC cord ( ) to the and then to an outlet of the proper voltage. With both channel 8amplifier
gain controls turned fully counterclockwise, turn the Power switch on, and raise the gain controls to achieve the desired sound level.
Please carefully review this manual to learn about all the features and of your new CPX Series power amplifier!designed-in behaviors
TM


Product specificaties

Merk: Crest Audio
Categorie: Receiver
Model: CPX 3

Heb je hulp nodig?

Als je hulp nodig hebt met Crest Audio CPX 3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Crest Audio

Handleiding Receiver

Nieuwste handleidingen voor Receiver