Creda TPRIII 1500M Handleiding

Creda Heater TPRIII 1500M

Lees hieronder de 📖 handleiding in het Nederlandse voor Creda TPRIII 1500M (4 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Installation and Operating Instructions

INCPUKP5RG Issue 6

TPRIII M Panel Convector Heaters

Dimensions

(millimetres)

Model s Watt A B( )

TPRIII 500M/MT 500 450 108

TPRIII 750M/MT/NC 750 620 108

TPRIII 1000M/MT/NC 1000 620 108

TPRIII 1250M/MT/NC 1250 688 108

TPRIII 1500M/MT/NC 1500 688 108

TPRIII 2000M/MT/MT7/NC 2000 860 108 Fig. 1

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Children shall not play with the appliance.

Cleaning and user maintenance shall not

be made by children without supervision.

Children of less than 3 years should be kept

away unless continuously supervised.

Children aged from 3 years and less than 8

years shall only switch on/off the appliance

provided that it has been placed or installed

in its intended normal operating position

and they have been given supervision or

instruction concerning use of the appliance

in a safe way and understand the hazards

involved. Children aged from 3 years and

less than 8 years shall not plug in, regulate

and clean the appliance or perform user

maintenance.

Note that due care and consideration must

be taken when using this heater in series

with a thermal control, a program controller,

a timer or any other device that switches on

the heat automatically, since a re risk exists

when the heater is accidentally covered or

displaced.

If the supply cord is damaged it must be

replaced by the manufacturer or service

agent or a similarly qualied person in order

to avoid a hazard.

WARNING: Servicing and product

repairs should only be undertaken by the

manufacturers approved service agent or a

similarly qualied person, using only exact

manufacturer approved spare parts.

The supply circuit to the heater must

incorporate a double pole isolating switch

having a contact separation of at least 3mm.

150

MIN

‘x’ 150

MIN

150

MIN

430

Important Safety Advice

When using electrical appliances, basic

precautions should always be followed to

reduce the risk of re, electrical shock, and

injury to persons, including the following:

IMPORTANT – The wall bracket supplied

with the appliance must be used.

WARNING – DO NOT USE THIS HEATER

IN THE IMMEDIATE SURROUNDINGS OF

A BATH, A SHOWER OR A SWIMMING

POOL.

IMPORTANT – If the heater is installed in a

room containing a bath or shower, it must be

so installed that switches and other controls

cannot be touched by a person using a bath

or shower.

Do not use outdoors.

Do not locate the heater immediately below

a xed socket outlet or connection box.

WARNING: In order to avoid overheating, do

not cover the heater. Do not place material

or garments on the heater, or obstruct the

air circulation around the heater, for instance

by curtains or furniture, as this could cause

overheating and a re risk.

NEVER cover or obstruct in any way the heat

outlet slots at the top of the heater or the air

inlet slots in the base of the heater.

The heater carries the Warning symbol

indicating that it must not be covered.

CAUTION - Some parts of this product

can become very hot and cause burns.

Particular attention has to be given where

children and vulnerable people are present.

This appliance can be used by children

aged from 8 years and above and by

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved.

Access to the Controls

The controls cover (see ‘x’ in Fig. 1) on your heater has a latch which

may be locked shut if desired using a small bladed screwdriver - see

Fig. 3.

To open the cover insert the blade of the screwdriver in the small

slot and rotate a quarter of a turn clockwise to disengage the latch.

The cover may then be hinged back towards the wall for access to

the controls.

Operation - Thermostat only models

Control of Output and Temperature see Fig. 4( )

The switch marked and controls the electricity supply to the heating O I

elements. The OFF position is marked .O

The switch marked - (half heat – full heat) provides a choice of I II

output as desired.

Electrical

WARNING – THIS APPLIANCE MUST BE EARTHED

The electrical installation must be carried out by a competent

electrician, and be in strict accordance with the current I.E.E.

regulations for Electrical Equipment in Buildings.

The heater is tted with a length of exible cable type H05VV-F size

3 x 1.0mm2 on models TPRIII 500 - 2000, for connection to the xed

wiring of the premises through a suitable connection box positioned

adjacent to the heater.

The supply circuit to the heater must incorporate a double pole isolating

switch having a contact separation of at least 3mm.

Supplementary Earth Bonding

Should Equipotential Earth Bonding be required the earthing conductor

in the supply cord is deemed to provide the supplementary bonding

connection (see Regulation 544.2.5, 17

th Edition I.E.E. Wiring

Regulations).

General

The TPR panel heater is designed for wall mounting on the brackets

supplied. It should only be operated when in the upright position as

shown.

All models are splashproof to IP24 standard.

Models TPR…MT are tted with a 24 hour programmable timer.

Model TPR…MT7 is tted with a 7 day programmable timer.

Models TPR…NC have no controls and are for use with external

thermostatic or programming controllers.

Before connecting the heater check that the supply voltage is the same

as that stated on the heater.

Please note that lit cigarettes, candles and oil burners, combined

with the convection effect of electric heaters can cause soot

deposits to build up on the surface directly above and to the sides

of the heater. This is not a fault of the heater. Extensive burning of

candles or smoking in the operating environment of this product

can produce heavy discolouration within a few months of use.

Wall Mounting

IMPORTANT – The wall brackets supplied with the appliance must

be used. The heater should be positioned observing the minimum

clearances stated around the heater - see .Fig. 1

DO NOT locate the heater immediately below a xed socket outlet

or connection box.

1. Remove wall mounting bracket from the back of the heater

by depressing the spring latch at the top of each bracket -

see .Fig. 2

255

MIN

Fig. 3

Fig. 4

Fig. 5

2. Fix the wall bracket securely to the wall through the four

screw holes provided.

3. Present the heater to the wall bracket, and engage lower

slots in the back with bracket.

4. Raise the heater to the upright position and push the heater

onto brackets to engage top latch.

Fig. 2

Thermostat Operation

The heater is tted with an adjustable thermostat enabling the room

temperature to be controlled by adjusting the setting accordingly. The *

setting represents a room temperature of approximately 5°C and may

be used for protection against frost. Higher temperature settings range

from 1-6 (max.) creating a room temperature of approximately 30°C.

A neon indicator light glows when the appliance is actually heating.

Switch on the heater and turn the thermostat knob to mark 6 opposite

the indicator mark (located on centre right of the knob - see & Fig. 4

5), and set selector switch to full heat output to warm the room rapidly.

When the room temperature has reached the desired level, turn the

thermostat knob back slowly until the thermostat just clicks off. The

heater will then maintain the room temperature at the chosen level,

provided that the correct size of heater has been selected for the

room to be heated.

NOTE – Should your heater fail to come on when the thermostat knob

is at a low setting, this may be due to the room temperature being

higher than the thermostat setting.

Operation - MT and MT7 Timer Models

Control of Output and Temperature see Fig. 5( )

The slide switch on the timer unit controls the electricity supply to the

heating elements on MT and MT7 models.

The switch marked - (half heat – full heat) provides a choice of I II

output as desired.

Thermostat Operation

- see above.

Using the Timer

The heater must be connected to the electricity supply for the timer to

operate. Set the timer by rotating the dial clockwise until the correct

time of day is indicated opposite the datum mark (located at centre

front of the timer - see ).Fig. 5

‘OFF’ Position

Set the timer switch to position. The timer operates but the heater

will not output any heat, as the electricity supply to the heating elements

has been disconnected.

Manual Operation

Set the timer switch to position. The heater will now operate

continuously under the control of the thermostat - see ‘Thermostat

Operation’ above.

Automatic Operation

Set the timer switch to position. The panel will now operate during

set ‘ON’ periods under the control of the thermostat.

To set the timer’s ‘ON’ and ‘OFF’ periods:

1. Using your nger tip or the tip of a

pencil, push in as many segments as

necessary around the dial, according to

the times you don’t require heat – see

Fig. 6. Each segment pushed in switches

the heater OFF for that part of the hour.

All other segments will be ‘ON’.

2. You can select as many ‘ON’ periods as you like, within the 24-hour

day. The settings will repeat every day until changed.

3. To change ‘ON’ and ‘OFF’ times, simply push in any ‘ON’ segments

you wish to cancel and pull out new ‘ON’ segments as required.

Note: On TI models each segment on the timer represents 20 mins.

MT7 Model/Day

The MT7 model is tted with 7 day programmable timer. In all other

respects it is identical in installation and operation to 24 hour timer

operation on MT models.

1. Setting the Time

The current day and time is set by rotating the timer dial clockwise

until the correct day and time is indicated opposite the datum mark.

2. Automatic Operation

Set the time switch to the symbol. Select the days and times you

require the heater to come on by pulling out the appropriate segments.

Each segment represents a 2 hour and 20 minute period for the day

indicated. The timer may be set to give as many ‘ON’ periods of any

length required in multiples of 2 hours and 20 minutes. The programme

will repeat itself every 7 days until changed.

The programme may be over ridden at any time by switching to or

and can be reinstated by switching back to setting.

Fig. 6

Safety - Overheat protection

For your safety this appliance is tted with a thermal cut-out. In the

event that the product overheats for some reason, the cut-out prevents

excessive temperatures on the product by cutting the power to the

heater. Once the heater has cooled down, it will reset automatically,

it will continue to cycle on and off automatically until the reason for

overheating is removed.

Cleaning

Before commencing cleaning, unplug the heater and allow it to cool.

Disconnect the electricity supply to the appliance.

The outside can be cleaned by wiping it over with a soft damp cloth

and then dried. Do not use abrasive cleaning powders or furniture

polish, as this can damage the surface nish.

To release heater from the wall bracket for cleaning or redecoration,

depress latch on both brackets (see ) and hinge forward.Fig. 2

After Sales Service

Your product is guaranteed for one year from the date of purchase.

Within this period, we undertake to repair or exchange this product free

of charge provided it has been installed and operated in accordance

with these instructions.

Your rights under this guarantee are additional to your statutory rights,

which in turn are not affected by this guarantee.

Should you require after sales service you should contact our customer

services help desk on 0844 879 3588. It would assist us if you can

quote the model number, series, date of purchase, and nature of the

fault at the time of your call. The customer services help desk will

also be able to advise you should you need to purchase any spares.

Please do not return a faulty product to us in the rst instance as

this may result in loss or damage and delay in providing you with a

satisfactory service.

Please retain your receipt as proof of purchase.

Product specificaties

Merk:	Creda
Categorie:	Heater
Model:	TPRIII 1500M

Heb je hulp nodig?

Als je hulp nodig hebt met Creda TPRIII 1500M stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Heater Creda

Creda TSR18MW Handleiding

6 Januari 2024

Creda CEP1500E Handleiding

6 Januari 2024

Creda TSRE150 Handleiding

6 Januari 2024

Creda CEP2000E Handleiding

6 Januari 2024

Creda CEP075E Handleiding

5 Januari 2024

Creda COR15TS Handleiding

5 Januari 2024

Creda TPRIII 500M Handleiding

5 Januari 2024

Creda TPRIII 1500M Handleiding

5 Januari 2024

Creda EPH500 Handleiding

5 Januari 2024

Creda EPH1500 Handleiding

5 Januari 2024

Handleiding Heater

Nieuwste handleidingen voor Heater

Gorenje ECT680X Handleiding

2 December 2024

Sencor SCF 4742RD Handleiding

1 December 2024

Sencor SCF 4741BK Handleiding

1 December 2024

Eurotronic Comet Plus Handleiding

1 December 2024

Astralpool Viron eVo 250 Handleiding

30 November 2024

Astralpool Viron eVo 350 Handleiding

30 November 2024

Global Profi 5000W Handleiding

30 November 2024

Dometic TwinBoost 8000H Handleiding

25 November 2024

Yamazen DC-ZT12 Handleiding

25 November 2024

Yamazen DMSF-J062 Handleiding

25 November 2024