Control4 Core 5 Handleiding
Control4
Audiostreamer
Core 5
Lees hieronder de 📖 handleiding in het Nederlandse voor Control4 Core 5 (2 pagina's) in de categorie Audiostreamer. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Additional resources
The following resources are available for more support.
• Control4 CORE series help and information: ctrl4.co/core
• Snap One Tech Community and Knowledgebase: tech.control4.com
• Control4 Technical Support: ctrl4.co/techsupport
• Control4 website: www.control4.com
Front view
A Activity LED—The LED indicates that the controller is streaming audio.
B IR window—IR receiver for learning IR codes.
C Caution LED—This LED shows solid red, then blinks blue during the boot
process.
Note: The Caution LED flashes orange during the factory restore
process. See “Reset to factory settings” in this document.
D Link LED—The LED indicates that the controller has been identified in a
Control4 project and is communicating with Director.
E Power LED—The blue LED indicates that AC power is connected. The
controller turns on immediately after power is applied to it.
Back view
A Power plug port—AC power receptacle for an IEC 60320-C13 power cord.
B Contact/Relay port—Connect up to four relay devices and four contact
sensor devices to the terminal block connector. Relay connections are
COM NC, (normally closed), and (normally open). Contact sensor NO
connections are , (signal), and (ground).+12 SIG GND
C ETHERNET—RJ-45 jack for a 10/100/1000 BaseT Ethernet connection.
D USB—Two port for an external USB drive or the optional Dual-Band Wi-Fi
USB Adapter. See “Set up external storage devices” in this document.
E HDMI OUT—An HDMI port to display system menus. Also an audio out over
HDMI.
F ID and FACTORY RESET—ID button to identify the device in Composer Pro.
The ID button on the CORE 5 is also an LED that displays feedback useful
during a factory restore.
G ZWAVE—Antenna connector for the Z-Wave radio
H SERIAL—Two serial ports for RS-232 control. See “Connecting the serial
ports” in this document.
I IR / SERIAL—Eight 3.5 mm jacks for up to eight IR emitters or for a
combination of IR emitters and serial devices. Ports 1 and 2 can be
configured independently for serial control or for IR control. See “Setting up
IR emitters” in this document for more information.
J DIGITAL AUDIO—One digital coax audio input and three output ports.
Allows audio to be shared (IN 1) over the local network to other Control4
devices. Outputs audio (OUT 1/2/3) shared from other Control4 devices or
from digital audio sources (local media or digital streaming services such
as TuneIn.)
K ANALOG AUDIO—One stereo audio input and three output ports. Allows
audio to be shared (IN 1) over the local network to other Control4 devices.
Outputs audio (OUT 1/2/3) shared from other Control4 devices or from
digital audio sources (local media or digital streaming services such as
TuneIn.)
L ZIGBEE—Antenna connector for the Zigbee radio.
Installing the controller
To install the controller:
1 Ensure that the home network is in place before starting system setup.
The controller requires a network connection, Ethernet (recommended)
or Wi-Fi (with optional adapter), to use all of the features as designed.
When connected, the controller can access web-based media databases,
communicate with other IP devices in the home, and access Control4
system updates.
A B C D E
A B C D E F H I J K LG
Control4 CORE 5 Controller
Installation Guide
Supported model
• C4-CORE5 Control4 CORE 5 Hub & Controller
Introduction
Designed for the ultimate multi-room automation and entertainment
experience, the Control4® CORE 5 Controller features the highest-quality
audio of the Control4® CORE Series and an advanced smart automation
experience for those larger projects including hundreds of smart devices. The
CORE 5 is built to automate sophisticated home theaters, complex interior and
exterior lighting scenes, vital security and communications systems, and multi-
zone climate controls.
The CORE 5 delivers a beautiful, intuitive, and responsive on-screen user
interface with the ability to create and enhance the entertainment experience
for any TV in the house. The CORE 5 can orchestrate a wide range of
entertainment devices including Blu-ray players, satellite or cable boxes,
game consoles, TVs, and virtually any product with infrared (IR) or serial (RS-
232) control. It also features IP control for Apple TV, Roku, televisions, AVRs,
or other network-connected devices, as well as smart automation control
utilizing contact, relay, and secure wireless Zigbee and Z-Wave control for
lights, thermostats, smart locks, and more.
For entertainment, the CORE 5 also includes a built-in music server that allows
you to listen to your own music library, stream from a variety of leading music
services, or from your AirPlay-enabled devices using Control4 ShairBridge
technology
Box contents
The following items are included in the box:
• CORE 5 controller
• AC power cord
• IR emitters (4)
• Rack ears (2, pre-installed)
• Rubber feet (4)
• External antennas (2, 1 for Zigbee and 1 for Z-Wave)
• Terminal blocks for contacts and relays
Accessories sold separately
• Control4 3-Meter Wireless Antenna Kit (C4-AK-3M)
• Control4 Dual-Band Wi-Fi USB Adapter (C4-USBWIFI OR C4-USBWIFI-1)
• Control4 3.5 mm to DB9 Serial Cable (C4-CBL3.5-DB9B)
Warnings
Caution! To reduce the risk of electrical shock, do not expose this
apparatus to rain or moisture.
Avertissement ! Pour réduire le risque de choc électrique, n’exposez
pas cet appareil à la pluie ou à l’humidité.
Caution! In an over-current condition on USB or contact output the
software disables the output. If the attached USB device or contact
sensor does not appear to power on, remove the device from the
controller.
Avertissement ! Dans une condition de surintensité sur USB ou sortie
de contact le logiciel désactive sortie. Si le périphérique USB ou
le capteur de contact connecté ne semble pas s’allumer, retirez le
périphérique du contrôleur.
Caution! If this product is used as a means to open and close a
garage door, gate, or similar device, use safety or other sensors
to ensure safe function. Follow appropriate regulatory and safety
standards governing project design and installation. Failure to do so
may result in property damage or personal injury.
Requirements and specifications
Note: We recommend using Ethernet instead of Wi-Fi for the best
network connectivity.
Note: The Ethernet or Wi-Fi network should be installed before you
install the CORE 5 controller.
Note: The CORE 5 requires OS 3.3 or higher.
Composer Pro is required to configure this device. See the Composer Pro User
Guide (
ctrl4.co/cpro-ug
) for details.
Specifications
Inputs / Outputs
Video out 1 video out—1 HDMI
Video HDMI 2.0a; 3840x2160 @ 60Hz (4K); HDCP 2.2 and HDCP 1.4
Audio out 7 audio out—1 HDMI, 3 stereo analog, 3 digital coax
Audio playback formats AAC, AIFF, ALAC, FLAC, M4A, MP2, MP3, MP4/M4A, Ogg
Vorbis, PCM, WAV, WMA
High-res audio playback Up to 192 kHz / 24 bit
Audio in 2 audio in—1 stereo analog, 1 digital coax
Audio delay on audio in Up to 3.5 seconds, depending on network conditions
Digital signal processing Digital coax in—Input level
Audio out 1/2/3 (analog)—Balance, volume, loudness, 6-band
PEQ, mono/stereo, test signal, mute
Digital coax out 1/2/3—Volume, mute
Signal-to-noise ratio <-118 dBFS
Total harmonic distortion 0.00023 (-110 dB)
Network
Ethernet 1 10/100/1000BaseT compatible port (required for controller
setup).
Wi-Fi Optional Dual-Band Wi-Fi USB Adapter
(2.4 GHz, 5 Ghz, 802.11ac/b/g/n/a)
Wi-Fi security WPA/WPA2
Zigbee Pro 802.15.4
Zigbee antenna External reverse SMA connector
Z-Wave Z-Wave 700 series
Z-Wave antenna External reverse SMA connector
USB port 2 USB 3.0 port—500mA
Control
IR OUT 8 IR out—5V 27mA max output
IR capture 1 IR receiver—front; 20-60 KHz
SERIAL OUT 4 Serial out—2 DB9 ports and 2 shared with IR out 1-2
Contact 4 contact sensors—2V-30VDC input,
12VDC 125mA maximum output
Relay 4 relays—AC: 36V, 2A maximum voltage across relay;
DC: 24V, 2A maximum voltage across relay
Power
Power requirements 100-240 VAC, 60/50Hz
Power consumption Max: 40W, 136 BTUs/hour
Idle: 15W, 51 BTUs/hour
Other
Operating temperature 32˚F 104˚F (0˚C 40˚C)~ ~
Storage temperature 4˚F 158˚F (-20˚C 70˚C)~ ~
Dimensions (H × W × D) 1.65 17.4 9.92" (42 442 252 mm)× × × ×
Weight 5.9 lbs (2.68 kg)
Shipping weight 9 lbs (4.08 kg)
2 Mount the controller in a rack or place it on a shelf. Always allow plenty
of ventilation. See “Mounting the controller in a rack” in this document.
3 Connect the controller to the network.
• Ethernet—To connect using an Ethernet connection, plug the data
cable from the home network connection into the controller’s RJ-45
port (labeled ETHERNET IN) and the network port on the wall or at the
network switch.
• Wi-Fi—To connect using Wi-Fi, first connect the controller to Ethernet,
and then use Composer Pro System Manager to reconfigure the
controller for Wi-Fi.
4 Connect system devices. Attach IR and serial devices as described in
“Connecting the IR ports/serial ports” and “Setting up IR emitters.”
5 Set up any external storage devices as described in “Setting up external
storage devices” in this document.
6 Power up the controller. Plug the power cord into the controller’s power
plug port and then into an electrical outlet.
Mounting the controller in a rack
Using the pre-installed rack-mount ears, the CORE 5 can easily be mounted in
a rack for convenient installation and flexible rack placement.
Connecting the serial ports
The CORE 5 controller provides four serial ports. SERIAL 1 and SERIAL 2 can
connect to a standard DB9 serial cable. IR ports 1 and 2 (SERIAL 3 and 4) can
be reconfigured independently for serial communication. If not used for serial,
they can be used for IR. Connect a serial device to the controller using the
Control4 3.5 mm-to-DB9 Serial Cable (C4-CBL3.5-DB9B, sold separately).
1 The serial ports support many dierent baud rates (acceptable range:
1200 to 115200 baud for odd and even parity). Serial ports 3 and 4 (IR 1
and 2) do not support hardware flow control.
2 See Knowledgebase article #268 (ctrl4.co/contr-serial-pinout) for pinout
diagrams.
3 To configure a port’s serial settings, make the appropriate connections
in your project using Composer Pro. Connecting the port to the driver will
apply the serial settings contained in the driver file to the serial port. See
the Composer Pro User Guide for details.
Note: Serial ports 1, 2, 3, and 4 can be configured as straight-
through or null with Composer Pro. Serial ports by default are
configured straight-through and can be changed in Composer by
selecting the option Null Modem Enabled (SERIAL 1, 2, 3, or 4).
Setting up IR emitters
The CORE 5 controller provides 8 IR ports. Your system may contain third-
party products that are controlled through IR commands. The included IR
emitters can send commands from the controller to any IR-controlled device.
1 Connect one of the included IR emitters into an IR OUT port on the
controller.
2 Remove the adhesive backing from the emitter (round) end of the IR
emitter and ax it to the device to be controlled over the IR receiver on
the device.
Setting up external storage devices
You can store and access media from an external storage device, for example,
a USB drive, by connecting the USB drive to the USB port and configuring
or scanning the media in Composer Pro. A NAS drive can also be used as an
external storage device; see the Composer Pro User Guide (ctrl4.co/cpro-ug)
for more details.
Note: We support only externally powered USB drives or solid-state
USB drives (USB thumb drives). USB hard drives that do not have a
separate power supply are not supported.
Note: When using USB storage devices on an
CORE 5 controller, a single primary partition formatted FAT32 is
recommended.
control4.com | 888.400.4070
Composer Pro driver information
Use Auto Discovery and SDDP to add the driver to the Composer project. See
the Composer Pro User Guide (ctrl4.co/cpro-ug) for details.
OvrC setup and configuration
OvrC gives you remote device management, real-time notifications, and
intuitive customer management, right from your computer or mobile device.
Setup is
plug-and-play, with no port forwarding or DDNS address required.
To add this device to your OvrC account:
1 Connect CORE 5 controller to the Internet.
2 Navigate to OvrC (www.ovrc.com) and log in to your account.
Add the device (MAC address and Service Tag numbers needed for
authentication).
Pluggable terminal block connectors
For the contact and relay ports, the CORE 5 makes use of pluggable terminal
block connectors which are removable plastic parts that locks in individual
wires (included).
To connect a device to the pluggable terminal block:
1 Insert one of the wires required for your device into the appropriate
opening in the pluggable terminal block you reserved for that device.
2 Use a small flat-blade screwdriver to tighten the screw and secure the
wire in the terminal block.
Example: To add a motion sensor (see Figure 3), connect its wires
to the following contact openings:
• Power input to +12V
• Output signal to SIG
• Ground connector to GND
Note: To connect dry contact closure devices, such as doorbells,
connect the switch between (power) and (signal).+12 SIG
Connecting the contact ports
The CORE 5 provides four contact ports on the included pluggable terminal
blocks. See the examples below to learn how to connect devices to the contact
ports.
Wire the contact to a sensor that also needs power (Motion sensor)
Wire the contact to a dry contact sensor (Door contact sensor)
Wire the contact to an externally powered sensor (Driveway sensor)
Connecting the relay ports
The CORE 5 provides four relay ports on the included pluggable terminal
blocks. See the examples below to learn now to connect various devices to the
relay ports.
Wire the relay to a single-relay device, normally open (Fireplace)
Wire the relay to a dual-relay device (Blinds)
Wire the relay with power from the contact, normally closed (Amplifier trigger)
Motion Sensor
+12V 0V NOCOM
Dry Contact
Driveway
Sensor
External
12V Power
Fireplace
Dual-Relay Blind
UP DOWNCOM
Relay 1 Relay 2
12V Trigger
Troubleshooting
Reset to factory settings
Caution! The factory restore process will remove the Composer
project.
To restore the controller to the factory default image:
1 Insert one end of a paper clip into the small hole on the back of the
controller labeled .RESET
2 Press and hold the button. The controller resets and the button RESET ID
changes to solid red.
3 Hold the button until the flashes double orange. This should take five ID
to seven seconds. The button flashes orange while the factory restore ID
is running. When complete, the button turns o and the device power ID
cycles one more time to complete the factory restore process.
Note: During the reset process, the button provides the same ID
feedback as the Caution LED on the front of the controller.
Power cycle the controller
1 Press and hold the button for five seconds. The controller turns o and ID
back on.
Reset the network settings
To reset the controller network settings to the default:
1 Disconnect power to the controller.
2 While pressing and holding the button on the back of the controller, ID
power on the controller.
3 Hold the button until button turns solid orange and the Link and ID ID
Power LEDs are solid blue, and then immediately release the button.
Note: During the reset process, the button provides the same ID
feedback as the Caution LED on the front of the controller.
LED status information
Just powered on
Boot started
Boot complete
Network reset check
Factory restore underway
Connected to Director
Playing audio
Updating
Update error
No IP address
Activity Caution Link Power
—Flashing LED —Solid LED
200-00722-A
2022-06-02 DH
Copyright 2022, Snap One, LLC. All rights reserved. Snap One and its respective logos are
registered trademarks or trademarks of Snap One, LLC (formerly known as Wirepath Home
Systems, LLC), in the United States and/or other countries. 4Store, 4Sight, Control4, Control4 My
Home, SnapAV, Mockupancy, NEEO, OvrC, Wirepath, and Wirepath ONE are also registered
trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the
property of their respective owners. Snap One makes no claim that the information contained
herein covers all installation scenarios and contingencies, or product use risks. Information
within this specification subject to change without notice.
A
More help
For the latest version of this document and to view additional materials, open
the URL below or scan the QR code on a device that can view PDFs.
Legal, Warranty, and Regulatory/Safety information
Visit snapone.com/legal for details.
MOST RECENT VERSION
ctrl4.co/core5-ig
MORE INFO ON CORE CONTROLLERS
ctrl4.co/core
Product specificaties
| Merk: | Control4 |
| Categorie: | Audiostreamer |
| Model: | Core 5 |
Heb je hulp nodig?
Als je hulp nodig hebt met Control4 Core 5 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Audiostreamer Control4
4 Mei 2024
4 Mei 2024
3 Mei 2024
Handleiding Audiostreamer
- Audiostreamer Philips
- Audiostreamer Asus
- Audiostreamer Onkyo
- Audiostreamer Pioneer
- Audiostreamer Yamaha
- Audiostreamer Advance Acoustic
- Audiostreamer Aluratek
- Audiostreamer Amazon
- Audiostreamer Argon
- Audiostreamer Audiolab
- Audiostreamer Bluesound
- Audiostreamer Bose
- Audiostreamer Dane Elec
- Audiostreamer Denon
- Audiostreamer Eminent
- Audiostreamer Harman Kardon
- Audiostreamer Icy Box
- Audiostreamer Imperial
- Audiostreamer KEF
- Audiostreamer Klipsch
- Audiostreamer Konig
- Audiostreamer Lenco
- Audiostreamer Marantz
- Audiostreamer Marmitek
- Audiostreamer Muse
- Audiostreamer NAD
- Audiostreamer Naim
- Audiostreamer Nedis
- Audiostreamer Sangean
- Audiostreamer Sonos
- Audiostreamer Stereoboomm
- Audiostreamer Teac
- Audiostreamer Technics
- Audiostreamer Telestar
- Audiostreamer Teufel
- Audiostreamer Vogels
- Audiostreamer Cambridge
- Audiostreamer Bang And Olufsen
- Audiostreamer Bowers And Wilkins
- Audiostreamer Caliber
- Audiostreamer Block
- Audiostreamer Pro-Ject
- Audiostreamer Clint
- Audiostreamer Chord
- Audiostreamer Russound
- Audiostreamer Travis
- Audiostreamer Esoteric
- Audiostreamer Oehlbach
- Audiostreamer On-Hold Plus
- Audiostreamer Triangle
- Audiostreamer Logitech UE
- Audiostreamer NuPrime
- Audiostreamer WiiM
Nieuwste handleidingen voor Audiostreamer
15 November 2024
2 November 2024
2 November 2024
23 September 2024
18 September 2024
26 Augustus 2024
20 Augustus 2024
24 Mei 2024
24 Mei 2024
24 Mei 2024