Cobra JumPack CPP 8000 Handleiding

Cobra powerbank JumPack CPP 8000

Lees hieronder de 📖 handleiding in het Nederlandse voor Cobra JumPack CPP 8000 (4 pagina's) in de categorie powerbank. Deze handleiding was nuttig voor 66 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

CPP8000

User Manual

Portable Power - Anytime, Anywhere!

Thank for purchasing the Cobra CPP8000 JumPack™ jump

starter portable PowerPack. Before using this product,

please read these instructions carefully to learn about the

features and capabilities of the JumPack and how you can

get the best out of it.

Note: Please charge your CPP8000 JumPack completely

prior to using it for the first time.

Charge the JumPack fully prior to use.

WARNING: Keep the unit clear of fire and water.

WARNING: Shock Hazard. Keep away from children. Do not

insert foreign objects into the jumper cables port/jack, the

USB output port, or the USB input jack. Do not expose this

product to water, rain, snow, condensation, or spray. Do not

open the JumPack to replace the internal battery. No user

replaceable parts are inside the JumPack.

WARNING: Explosion Hazard. Do not use this product where

there are flammable fumes or gases, such as an inadequately

vented bilge of a boat, or near propane tanks. Do not use this

product in an enclosure containing automotive-type lead-acid

batteries.

The jump start cable clamps must be connected positive to

positive (red clip to battery (+)) and negative to negative

(black clip to battery (-)). A reverse polarity connection

(positive to negative) may cause damage to the JumPack

and/or create a sparking/explosion hazard.

WARNING: Fire Hazard

Do not crush or puncture the JumPack. Never allow the jump start

cables’ red and black clamps’ metal contacts to touch each other

or another common metal conductor. This could cause damage to

the unit and/or create a fire hazard. Always disconnect the jump

start cables from the JumPack after each use and store separately.

The jump start feature is designed for short term operation only.

Turn the ignition key for at a time. no more than 3 seconds

Operating the jump start feature for more than may 3 seconds

cause damage to the unit. Allow the JumPack to cool down for

at least after each jump start attempt.1 minute

IMPORTANT SAFETY INSTRUCTIONS Caution: Operating temperature

Do not expose the JumPack to temperatures over +113° F (+45° C) or

under -14° F (-10° C). Using the JumPack at high or low temperatures

may reduce the internal battery capacity and shorten the battery life.

Note: In extreme cold weather conditions, please bring the JumPack

indoors for best results.

Precautions when working with batteries

WARNING: Explosion and fire hazard

Follow all instructions published by the battery manufacturer and

the manufacturer of the equipment in which the battery is installed.

2. Make sure the area around the battery is well-ventilated.

3. Never smoke or allow a spark or flame in the vicinity of the

engine or batteries.

4. Be careful not to drop a metal object on the battery or allow a

metal tool to simultaneously touch the positive and negative

cable ends or battery terminals.

5. Remove personal metal items such as rings, bracelets,

necklaces, and watches when working with batteries. Batteries

produce a short-circuit current high enough to weld a ring or

other similar objects to metal, causing a severe burn.

6. If you need to remove a battery, always remove the negative

terminal from the battery first. Make sure all accessories are

off so you don’t cause an arc.

7. Someone should be within range of your voice, or close

enough to come to your aid when you work near batteries.

Have plenty of fresh water, soap and a supply of baking soda on

hand in the area of the batteries in case of contact with battery

acid. Baking soda neutralizes lead acid battery electrolyte.

The JumPack is supplied with a rechargeable Li-Cobalt battery.

This battery is self-contained and not consumer replaceable. Battery

must be disposed of properly when it no longer holds a charge.

Proper charging practices will increase the life of the batteries.

For

information on battery recycling call toll free 800-822-8837.

Product:

Battery Status Indicator Light Bar

Jump Starter Cable Input

DC 14V Charge Input

USB 5V 2.4

Amp Output

LED Flashlight

Power/Flashlight/Battery

Capacity Button

Car adaptor

Recharging the JumPack:

The CPP8000 JumPack can be recharged with the supplied 13.8V

DC vehicle charger or with the supplied micro USB to standard USB

cable connected to a 5V, 1A USB source, laptop or USB output AC

adapter (not included).

When the CPP8000 is charging; the light bar will show the current

battery life. The last section of the light bar that is lit will blink to

show that the JumPack is charging. When the JumPack is fully

charged the light bar will turn off automatically.

For best battery performance the JumPack should be fully

recharged every 3 months.

Operation:

Check Battery Capacity:

To check the battery capacity of the JumPack press the

Power/Flashlight button on the top of the unit with no device

connected. The green lightbar will show the remaining

battery capacity:

1st Section on: 10%-40% charge

2nd Section on: 40%-65% charge

3rd Section on: 65%-85% charge

4th Section on: 85%-100% charge

Note: When charging a device the section light may decrease

while the JumPack is in use. The battery capacity indicator

cannot accurately measure the capacity during rapid

charging. To confirm the real battery capacity, disconnect

the device being charged and press the power/flashlight/

capacity button.

Battery Status Indicator Light Bar

123 4

INPU T

14V 1A

OU T PU T

5V 2. 4A

INPU T

5V 1. 8A

USB 5V 1.8

Amp Input

Jumper cable

with clamps

Micro USB to

Standard USB

Cable

Checking the Fuse:

The jump cables are designed with an in-line fuse to protect the

jumpack in the event of an over-load condition. The jump cables

include a clear case to use in checking to be sure the in-line

fuse is intact:

Fuse Intact

CAUTION: Do not use the jump cables if the fuse appears

to opened or damaged. Please go to www.cobra.com for more

information.

Open or Damaged Fuse

INPUT

14V 1A

OUTPUT

5V 2.4A

INPUT

5V 1.8A

Product Specification:

• Li-Cobalt rechargeable battery: 11.1V/22.2Wh

• Size: 5.60” x 3” x 0.75”

(142mm x 76.2mm x 19.05mm)

• Weight: 10.58 oz. (300g.)

• Recharge times: 3 hours/13.8V DC

15 hours/5V USB

• Starting/Peak Current: 180 Amps/360 Amps

• USB Output: 5V 2.4 Amps

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician

for help.

WARNING: Any modifications made to this device that are not expressly

approved by party responsible for compliance could void the user’s authority

to operate this device.

Cobra® and the snake design are registered trademarks of

Cobra Electronics Corporation, USA.

Cobra Electronics Corporation™ is a trademark of Cobra

Electronics Corporation, USA.

PROPOSITION 65 WARNING: This product contains a chemical known to

the State of California to cause cancer and birth defects or other

reproductive harm.

Limited 1-Year Warranty:

For Products Purchased in the U.S.A.

Cobra Electronics Corporation warrants that its Cobra CPP8000 JumPack

USB Charger, and the component parts thereof, will be free of defects in

workmanship and materials for a period of one year from the date of first

consumer purchase. This warranty may be enforced by the first consumer

purchaser, provided that the product is utilized within the U.S.A.

Cobra will, without charge, repair or replace, at its option, defective

USB charger, products or component parts upon delivery to the Cobra

Factory Service Department, accompanied by proof of the date of first

consumer purchase, such as a duplicated copy of a sales receipt.

You must pay any initial shipping charges required to ship the product

for warranty service, but the return charges will be at Cobra’s expense,

if the product is repaired, this warranty gives you specific rights, and

you may also have other rights which vary from state to state.

Exclusions: This limited warranty does not apply:

1. To any product damaged by accident.

2. In the event of misuse or abuse of the product, or as a result of

unauthorized alterations or repairs.

3. If the serial number has been altered, defaced or removed.

4. If the owner of the product resides outside the U.S.A.

All implied warranties, including warranties of merchantability and

fitness for a particular purpose are limited in duration to the length of

this warranty.

Cobra shall not be liable for any incidental, consequential or other

damages; including, without limitation, damages resulting from loss of

use or cost of installation.

Some states do not allow limitations on how long an implied warranty

lasts and/or do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitations may not apply to you.

For Products Purchased Outside The U.S.A.

Please contact your local dealer for warranty information.

Product Service:

For any questions about operating or installing this new Cobra

product, or if parts are missing…PLEASE CALL COBRA

FIRST…do not return this product to the store. If this product

should require factory service, please call Cobra before sending the

product. This will ensure the fastest turn-around time on any repair.

If Cobra asks that the product be sent to its factory, the following

must be furnished to have the product serviced and returned:

For Warranty Repair include some form of proof-of-purchase,

such as a mechanical reproduction or carbon of a sales receipt.

Make sure the date of purchase and product model number are

clearly readable. If the originals are sent, they cannot be returned;

2. Send the entire product;

3. Enclose a description of what is happening with the product.

Include a typed or clearly printed name and address of where

the product is to be returned, with phone number (required

for shipment);

4. Pack product securely to prevent damage in transit. If possible,

use the original packing material;

Ship prepaid and insured by way of a traceable carrier such as

United Parcel Service (UPS) or Priority Mail with delivery

confirmation to avoid loss in transit to: Cobra Factory Service,

Cobra Electronics Corporation, 6500 West Cortland Street,

Chicago, Illinois 60707 U.S.A.;

6. If the product is in warranty, upon receipt of the product it will

either be repaired or exchanged depending on the model.

Please allow approximately 3 – 4 weeks before contacting Cobra

for status. If the product is out of warranty, a letter will

automatically be sent with information as to the repair charge or

replacement charge.

For any questions, please call 773-889-3087 for assistance or visit

us online at www.cobra.com.

FCC Statement:

• Lithium Cobalt rechargeable battery.

• 180 Amp Starting Current / 360 Amp Peak Current.

• 5V/2.4 Amp USB Output for rapid charging of portable devices.

• High Intensity work LED light.

• Rechargeable by 13.8 V DC car adapter or by 5V USB.

Product Features:

Starting a Vehicle:

. Make sure the JumPack is fully charged.

2. Turn off all the accessories on the vehicle.

3. Disconnect the battery cables from the JumPack.

4. Connect the RED clamp to the POSITIVE post of the battery.

Connect the BLACK clamp to the NEGATIVE post of the battery.

Connect the battery cables into the jump cable port.

Be sure that the plug is firmly pressed into the JumPack.

Turn the ignition key to start the vehicle. Do not crank the

ignition for more than 3 SECONDS. If the engine is cranked

for more than , the fuse may open. See page 3 SECONDS 5 to

see condition of fuse.

NOTE: If your car does not start after 3 attempts, consult with

a mechanic.

If the engine starts;

8. Disconnect the cables from the JumPack, then from the

battery posts.

9. Leave the engine running for at least twenty minutes to

allow the vehicle battery to recharge.

10. If the vehicle does not start on the first try, WAIT FOR

1 MINUTE before trying to start the vehicle again

NOTE: Go to www.cobra.com for instructional steps to

jumpstart a vehicle.

Charging a 5V USB Device:

To charge a 5V USB device, connect the devices’ cable to the

JumPack’s USB output. The JumPACK will turn on, and start

charging the device automatically. The light bar will indicate that

the device is charging.

LED Flashlight:

Press the Power/Flashlight/Battery capacity button for 3 seconds to

turn on the LED flashlight. Press and hold to turn flashlight Off.

8 9

START

INPUT

14V 1A

OUTPUT

5V 2.4A

INPUT

5V 1.8A

Customer Support & Trademarks:

Customer Support

Should there be any problems with this product or further information

needed on its features please visit www.cobra.com for support, frequently

asked questions, Declarations of Conformity, and the electronic manual.

For warrant y and customer service information please contact the seller.

WEEE

For European Community Users

Cobra Electronics Corporation complies with Directive 2012/19/EU OF

THE EUROPEAN PARLIAMENT AND OF THE COUNCIL 4 JULY 2012 on

waste electrical and electronic equipment (WEEE).

Waste Electrical and Electronic Equipment Information

This product has required the extraction and use of natural resources for

its production. It may contain hazardous substances that could impact

health and the environment, if not properly disposed. In order to avoid

the dissemination of those substances in our environment and to

diminish the pressure on the natural resources, we encourage you to use

the appropriate take-back systems for product disposal. Those systems

will reuse or recycle most of the materials of the product you are disposing

in a sound way.

The crossed out wheeled bin symbol informs you that the product

should not be disposed of along with municipal waste and invites you

to use the appropriate separate take-back systems for product disposal.

If you need more information on the collection, reuse and recycling

systems, please contact your local or regional waste administration.

You may also contact your supplier for more information on the

environmental performances of this product.

The product label is located on the bottom of the unit.

Trademark Statement

Cobra and the snake design are proprietary trademarks of Cobra Electronics

Corporation, USA.

Product specificaties

Merk:	Cobra
Categorie:	powerbank
Model:	JumPack CPP 8000
Kleur van het product:	Black, Grey
Ingebouwd display:	Nee
Gewicht:	260.8 g
Breedte:	72.9 mm
Diepte:	16.51 mm
Hoogte:	139.7 mm
Gewicht verpakking:	567 g
Breedte verpakking:	184.15 mm
Diepte verpakking:	57.15 mm
Hoogte verpakking:	260.35 mm
LED-indicatoren:	Ja
Aan/uitschakelaar:	Ja
Meegeleverde kabels:	Micro-USB
Accu/Batterij voltage:	11.1 V
Lader compatibiliteit:	Tablet, GPS, E-book reader
Ingebouwde zaklamp:	Ja
Batterijtechnologie:	Lithium-kobaltoxide (LiCoO2)