Chord Anni Handleiding


Lees hieronder de šŸ“– handleiding in het Nederlandse voor Chord Anni (7 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/7
Operation 3.0
Chord Electronics
Anni | Manual
_
Chord Electronics
Product Communication | English
_
The Pumphouseī˜Ÿ Farleigh Lane,
East Farleigh, Maidstone
ME16 9NB United Kingdon
info@chordelectronics.co.uk
chordelectronics.co.uk
Anni
Manual
_
V.1
Power output 10 W 8 ohms
THD 0.02 %
Signal to noise -92 dB
Noise ļ¬‚oor -110 dB
Frequency response 5 Hz-60 kHz
chordelectronics.co.uk
_
Gain
Anni beneļ¬ts from a two-stage (high and low) gain function on the
loudspeaker outputs (only) to suit a wide range of partnering speakers.
Press the gain button to alternate between low (blue) and high (red) gain
modes, allowing 3 seconds to switch between modes.
When using either of the headphone outputs, Anni is automatically
switched to low gain mode. If when inserting headphones Anni was
previously set to high gain (red) the gain sphere will show purple, before
reverting back to red when the headphones are removed. If low gain (blue)
was previously selected, the gain sphere will remain blue and continue to
display blue when the headphones are disconnected.
If using Anni with Qutest, ensure Qutestā€™s output voltage is set no higher
than 2 V. The Qutest manual describes how to set output voltage.
Placement
Anni beneļ¬ts from extensive casework ventilation and a cooling fan for
demanding environments. Always ensure Anni is used in a well-ventilated
setting, away from direct sunlight and heat sources, and has suī˜cient
space around the unit.
Chord Electronicsā€™ Qutest Stand System (available separately) has been
designed to perfectly house Anni. Otherwise, care should be taken not to
stack other units on Anni.
Support
If you need support, in the ļ¬rst instance, please contact your supplying
retailer who will be best placed to assist you. If you need additional help
beyond that of your retailer, please visit our support page: chordelectronics.
co.uk/get-support
Speciļ¬cations
Inputs 2.1
Connect to any line level source component using a standard RCA cable.
Rear
Front
Introduction
Anni is a next-generation desktop integrated ampliļ¬er that complements the
high quality of our multi-award-winning Qutest DAC and Huei phono stage. We
took a diī˜œerent approach to the design and created a powerful, desktop device
for headphones and desktop loudspeakers that belies its compact dimensions.
Accurately controlled across the entire audio bandwidth with extraordinary
low frequency capability, Anniā€™s protection circuitry allows for the delivery of
enormous peak current outputs for its size whilst avoiding overdrive; it does this
diī˜œerently to other ampliļ¬ers on a half-cycle by half-cycle basis. If the output
of the amp is being over-driven, Anni will detect it and collapse the waveform
on each over-driven, half-cycle. So not clipping like other ampliļ¬ers but instead
going from a completely undistorted waveform to one that is missing half-cycles
i.e. it becomes heavily distorted suddenly until the level is slightly reduced. Then
the music signal will totally recover without any harm occurring to the ampliļ¬er
or speaker, with the music being once again undistorted.
Power on/oī˜ 3.1
With connections successfully made (as per section 2.0), and volume set to
zero, press the power button. The button will display green, before settling
on cyan. Pressing the power button again puts the unit in standby; the
button will display red.
Note: if either of the headphone outputs are connected, the power button
will display green to show the speaker output has been disconnected. If the
headphones are then removed, the power button will revert to cyan and the
speaker output will become active.
Select an input 3.2
Select input 1 or 2 by pushing the volume knob sequentially. Input 1 is
indicated by a blue LED ring, input 2 is red.
Ampliļ¬er operation 3.3
With connections successfully made and with volume set to zero, select the
input, press play on the chosen source and adjust Anniā€™s volume accordingly.
Connections and
controls
Operation
2.0 3.0
6.35 mm (1/4 inch)
headphone output
Volume control/input
select
3.5 mm headphone output
12 V DC output
Speaker output left
channel
Speaker output right
channel
Line level inputs 1 and 215 V DC power input
General operation and
important information
1.0
Chord Electronics
Anni | Manual
_
Connecting to loudspeakers 2.2
Connect to the loudspeaker using 4 mm banana-plug-terminated speaker
cable, observing polarity.
Ground terminal
Gain
button
Power
button
Connecting to headphones 2.3
Using the front two outputs, connect headphones with 6.35 mm (1/4-
inch) or 3.5 mm terminations to Anni and the output will automatically be
selected. The volume controls both headphone outputs simultaneously: they
are not independently controllable.
Headphone operation 3.4
Anni has both 6.35 mm (1/4 inch) and 3.5 mm headphone outputs, which
can be used both individually or simultaneously meaning two can listen.
With the volume set to zero, connect to one or both headphone outputs and
slowly increase the volume.
Note: if connecting headphones when music is already playing through
the loudspeakers, a short delay will be experienced before the headphone
output becomes active (to protect the amp). In addition, low gain will be
automatically selected. Removing the headphones (with speakers still
connected) will revert the output signal back to the speakers.
Input 1 Input 2
Right speaker
channel
Left speaker
channel
6.35 mm
headphone
3.5 mm
headphone
Input 1 Input 2
Power connection
Anni is supplied with an external power supply and has been designed to
be permanently connected to a power source. Connect the included 15 V supply
to Anni. If hum occurs, use the ground terminal to connect to an available
earth point. Always set the volume to zero before playback and before
connecting/removing headphones.
Connections and controls 2.0


Product specificaties

Merk: Chord
Categorie: Receiver
Model: Anni

Heb je hulp nodig?

Als je hulp nodig hebt met Chord Anni stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Chord

Handleiding Receiver

Nieuwste handleidingen voor Receiver