Chief SLM2220 Handleiding
Chief
Projector accessoire
SLM2220
Lees hieronder de 📖 handleiding in het Nederlandse voor Chief SLM2220 (1 pagina's) in de categorie Projector accessoire. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-000148 RevB
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-2220, SSM-2220, SLB-2220 and SLM-2220 Interface Brackets
SSB-2220, SSM-2220, SLB-2220 and SLM-2220 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information. Unpack carton and verify kit contents. If any listed parts are
missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the encircled
locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket
installation.
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down.
3. Place interface bracket onto bottom of projector with three threaded inserts face up and two towards front of projector. Secure interface bracket to
projector using selected screw for model of projector (countersink screw or pan head screw).
4. Countersink screw in center countersink hole and pan head mounting screw in flush mounting hole. Your projector may require one or three
spacers for aligning bracket flat to projector. (Some models may suspend over bottom and have space between bracket and projector.)
Hitachi CP-X270W
1. Place projector upside down on table with projector lens facing away. Stack 1/2" x .190 x 1/2" and 1/2" x .190 x 3/8" on top of each other and
centered over right threaded insert in front of projector. Using two 1/2" x .218 x 1/4" ,1/2" x .218 x 1/4" and 1/2" x .258 x 3/16" spacers, stack and
place them over three threaded inserts on left.
2. Place interface bracket onto projector and align spacers and mounting holes.
3. Position and align interface bracket to projector using M4 x 30mm countersink screw in middle of bracket, M4 x 30mm Phillips pan head screw in
right of bracket, and M4 x 16mm Phillips pan head screw in left of bracket. Tighten all fasteners at this time, securing the bracket to the projector.
Hitachi CP-S307W, CP-X380W, CP-X385W
1. Place projector upside down on table with projector lens facing away. Stack 1/2" x .218 x 1/4" and 1/2" x .258 x 3/16" spacers on top of each other
centered over right threaded insert in front of projector. Using two 1/2" x .258 x 3/16" spacers, place one over middle threaded insert and one over
left threaded insert of projector.
2. Place interface bracket onto projector and align spacers and mounting holes.
3. Position and align interface bracket to projector using M4 x 16mm countersink screw in middle of bracket, M4 x 20mm Phillips pan head screw in
right hole of bracket and M4 x 16mm Phillips pan head screw in left hole of bracket. Tighten all fasteners at this time, securing the bracket to the
projector.
NOTE: Security Screws can be substituted when mounting interface bracket to projector by using the parts and installation instructions in
the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (3) 1/2" x .218" x 1/4" Round Spacer **** (1) Screw, Phillips Flat Head,
Machine, M4 x 16mm **** (1) Screw, Phillips Pan Head,
Machine, M4 x 30mm ****
(4) 10 - 24 Thumb
Nuts** (3) 1/2" x .194" x 1/2" Round Spacer **** (1) Screw, Phillips Pan Head,
Machine, M4 x 16mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
(1) All-Points Security
Kit (3) 1/2" x .194" x 3/8" Nylon Spacer **** (1) Screw, Phillips Flat Head Machine,
M4 x 25mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
(2) Washer, Flat, M4 (1) Screw, Phillips Pan Head, Machine,
M4 x 8mm **** (1) Screw, Phillips Pan Head,
Machine, M4 x 20mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
SLB-2220 SLM-2220
Towards front of
projector
Towards front of
projector
(
N
ote: SSB-style interface bracket connections
a
r
e
e
n
c
ir
c
l
e
d
)
(Note: SSM-style interface bracket connection
s
a
re encircled)
Product specificaties
| Merk: | Chief |
| Categorie: | Projector accessoire |
| Model: | SLM2220 |
| Kleur van het product: | Zwart |
| Gewicht verpakking: | 1000 g |
| Aantal per verpakking: | 1 stuk(s) |
Heb je hulp nodig?
Als je hulp nodig hebt met Chief SLM2220 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Projector accessoire Chief
18 November 2024
17 November 2024
17 November 2024
17 November 2024
17 November 2024
17 November 2024
17 November 2024
17 November 2024
17 November 2024
14 November 2024
Handleiding Projector accessoire
- Projector accessoire Sony
- Projector accessoire Casio
- Projector accessoire Panasonic
- Projector accessoire Auna
- Projector accessoire Barco
- Projector accessoire BenQ
- Projector accessoire Hitachi
- Projector accessoire InFocus
- Projector accessoire Manhattan
- Projector accessoire Nec
- Projector accessoire Nedis
- Projector accessoire Newstar
- Projector accessoire Peerless
- Projector accessoire Sanyo
- Projector accessoire Speaka
- Projector accessoire Viewsonic
- Projector accessoire Vogels
- Projector accessoire XGIMI
- Projector accessoire Omnitronic
- Projector accessoire Optoma
- Projector accessoire Sanus
- Projector accessoire Vision
- Projector accessoire Gabor
- Projector accessoire Lindy
- Projector accessoire Da-Lite
- Projector accessoire AV:link
- Projector accessoire Peerless-AV
- Projector accessoire Projecta
- Projector accessoire Chipolino
- Projector accessoire Konig & Meyer
- Projector accessoire Roadinger
- Projector accessoire Tempest
- Projector accessoire Premier Mounts
- Projector accessoire Gravity
- Projector accessoire Elite Screens
- Projector accessoire Kingpin Screens
- Projector accessoire Kanto
- Projector accessoire V7
- Projector accessoire Christie
- Projector accessoire Unicol
- Projector accessoire My Wall
- Projector accessoire Smart Media
Nieuwste handleidingen voor Projector accessoire
19 November 2024
19 November 2024
30 Juli 2024
29 Juli 2024
29 Juli 2024
29 Juli 2024
26 Juli 2024
26 Juli 2024
9 Juli 2024
9 Juli 2024