Chief SLM204 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Chief SLM204 (1 pagina's) in de categorie Projector accessoire. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-
mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The
information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the
information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
© 2007 Chief Manufacturing, 8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-000271
9/10/07
SLB-204 and SLM-204 Interface Brackets
for Christie LX650, EIKI LC-X80, SANYO PLC-XP100L,
SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling
1-800-582-6480.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation:
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.
1. Screw six thumb screws onto six 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket onto the bottom of the projector lining up the four holes in the bracket with the four threaded inserts in the bottom
of the projector.
4. .Using the four M6 X 12mm mounting screws and washers, start them into the mounting holes by hand and secure all four fasteners at
this time.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
(1) Interface Bracket (4) Washer, Flat, M6
(6) 10-24 Thumb Nuts ** (4) SCREW, Pan head, M6 x 12mm
(1) All-Points Security Kit
**Only used when installing SLB Interface brackets.
SLB-204
SLM-204
Towards front of Towards front of
Projector
Projector


Product specificaties

Merk: Chief
Categorie: Projector accessoire
Model: SLM204
Kleur van het product: Zwart
Gewicht verpakking: 2000 g
Aantal per verpakking: 1 stuk(s)

Heb je hulp nodig?

Als je hulp nodig hebt met Chief SLM204 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Projector accessoire Chief

Chief

Chief SLM248 Handleiding

18 November 2024
Chief

Chief SLM251 Handleiding

17 November 2024
Chief

Chief SLM255 Handleiding

17 November 2024
Chief

Chief SLM293 Handleiding

17 November 2024
Chief

Chief SLM3000 Handleiding

17 November 2024
Chief

Chief RPMAU Handleiding

17 November 2024
Chief

Chief SLM230 Handleiding

17 November 2024
Chief

Chief WM2I Handleiding

17 November 2024
Chief

Chief RSMD311 Handleiding

17 November 2024
Chief

Chief RPMA368 Handleiding

14 November 2024

Handleiding Projector accessoire

Nieuwste handleidingen voor Projector accessoire