Chief SLB3131 Handleiding

Chief Projector accessoire SLB3131

Lees hieronder de 📖 handleiding in het Nederlandse voor Chief SLB3131 (3 pagina's) in de categorie Projector accessoire. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use

of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or

implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief Manufacturing, a products division of Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8802-002020 Rev01

a Duchossois Group Company

05/09

SSB-3131, SSM-3131, SLB-3131 and SLM-3131 Interface Brackets

SSB-3131, SSM-3131, SLB-3131 and SLM-3131 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the

specific installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation Instructions

WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing Interface bracket.

NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down.

3. Locate the two-rear rubber pads as seen in Figure 1. Cut the small tab on each rear pad so they can push down into the mounting slots.

Figure 1:

(1) Interface Bracket (1) Locking Tab

(4) 10 - 24 Thumb Nuts** (1) # 8 - 32 x 1/2” Phillips Pan Screw

(1) All-Points Security Kit

**Only used when installing SLB/SSB interface brackets.

NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the

encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style

interface bracket installation.

Towards front of

projector

Towards front of

projector

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use

of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or

implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief Manufacturing, a products division of Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8802-002020 Rev01

a Duchossois Group Company

05/09

4. Locate the front adjustable foot as seen in Figure 2. Cut the two small tabs on the front center mounting slot so it can push down into the

mounting slot.

Figure 2:

5. Align the interface bracket’s two rear and one front tabs with the two rear and one front mounting slots in the projector. Insert the bracket

tabs down into the mounting slot and slide the bracket back toward the rear of the projector as seen in Figure 3.

Figure 3:

6. Locate the pre-packaged interface bracket locking tab. Place the locking tab through the front opening in the mounting bracket and lay

it on its side as seen in Figure 4.

Figure 4:

7. Using a screwdriver, slide the locking tab to the left and push the end of the locking tab into the mounting slot in front of the front mounting

tab on the bracket as seen in Figure 5.

Figure 5:

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use

of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or

implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.