Chief Fusion FHB3017 Handleiding

Chief Niet gecategoriseerd Fusion FHB3017

Lees hieronder de 📖 handleiding in het Nederlandse voor Chief Fusion FHB3017 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Vertical Offset Interface Bracket
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FHB3017 / FHB5017
FHB3017 / FHB5017 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the maximum weight
installed on the interface bracket does not exceed the weight
limit of the mount to which it is being attached.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
4.92
125.0
FHB3017 / FHB5017 Installation Instructions
3
TOOLS / PARTS FOR INSTALLATION
3/16" (included)
M5 (included)
A (2)
[channel
bracket]
B (4)
5/16-18 x 1/2"
C (2)
M8 x 25mm 3/16"
D (2) M5
E (4)
F (1)
G (1)
M8 x 30mm
.750x.344x.500
ASSEMBLY AND INSTALLATION
1. Install wall mount to wall following mount instructions up
until the interface brackets are to be attached to the display.
2. Lay display face down on a protective surface.
3. Position four spacers (E) over four holes on back of display.
(See Figure 1)
4. Install two M8 x 25mm Phillips pan machine screws (C)
through two channel brackets (A), spacers (E) and into back
of display. (See Figure 1)
NOTE: Use alignment holes in channel brackets to line up the
wall mount interface brackets for either a 3-1/2" or 5"
vertical offset. (See Figure 2)
Figure 1
CAUTION: Using screws of improper length or diameter
may cause damage to your display! Only use screws
provided! Ensure that two M8 x 25mm screws (C) are used
for lower holes and two M8 x 30mm screws (D) are used for
upper holes!
5. Install two M8 x 30mm button head cap screws (D) through
two wall mount interface brackets, two channel brackets (A),
spacers (E) and into back of display. (See Figure 1)
6. Use four 5/16-18 1/2" button head cap screws (B) to secure
two wall mount interface brackets to two channel brackets
(A). (See Figure 1)
Figure 2
7. Complete the installation following the wall mount
installation instructions.
5
(C) x 2
(D) x 2
(A) x 2
43
(E) x 4
wall mount
interface brackets
6
(B) x 4
3 1/2" offset (lower
alignment hole in
channel bracket shows
through diamond
in wall mount
interface bracket)
5" offset (upper
alignment hole in
channel bracket shows
through diamond
in wall mount
interface bracket)


Product specificaties

Merk: Chief
Categorie: Niet gecategoriseerd
Model: Fusion FHB3017

Heb je hulp nodig?

Als je hulp nodig hebt met Chief Fusion FHB3017 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Chief

Chief

Chief DVM27U2E Handleiding

14 November 2024
Chief

Chief DVM27U3E Handleiding

14 November 2024
Chief

Chief DVM27U2 Handleiding

14 November 2024
Chief

Chief DVM27U4 Handleiding

14 November 2024
Chief

Chief DVM27U4E Handleiding

13 November 2024
Chief

Chief DVM27U3 Handleiding

13 November 2024
Chief

Chief CSA100 Handleiding

6 November 2024
Chief

Chief PACPC1 Handleiding

6 November 2024
Chief

Chief TS325TU Handleiding

3 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd