Chamberlain CWPIR Handleiding

Chamberlain Bewegingsdetector CWPIR

Lees hieronder de 📖 handleiding in het Nederlandse voor Chamberlain CWPIR (2 pagina's) in de categorie Bewegingsdetector. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Carton Inventory

Assembly & Programming

Attach PIR Motion Sensor box

to mounting plate with large

silver screw. Tighten screw

until PIR Motion Sensor stays

in place when repositioned.

Passive Infra-Red (PIR)

Motion Sensor

Swivel Bushing

Mounting PlateSun/Rain Shield

Install 4 AA Alkaline

batteries. (Lithium batteries

recommended for colder

environments.)

LED light will ﬂ ash.

Antenna

OFF

1 2

SWITCH SETTINGS

Switch #1 Switch #2

Learn

Button

OFF Low Sensitivity

ON High Sensitivity (Default)

OFF 15 Feet (4.5 m) Detection Range

ON 30 Feet (9.1 m) Detection Range

(Default)

NOTE: To avoid unwanted detection of small animals move

Switch #2 to OFF.

PIR Motion Sensor

SWITCH #1:

SWITCH #2:

A Ensure Base Station and PIR

Motion Sensor are in close

proximity to each other.

Press and release Learn

Button on Base Station.

Buzzer will sound.

B Within 60 seconds, press the

Learn Button on the inside of

the PIR Motion Sensor. LED

light will illuminate and Base

Station will buzz.

3Learn Button

Test PIR Motion Sensor by

waving hand in front of sensor.

LED light should ﬂ ash and

the Base Station will buzz X

number of times indicating

which sensor has been

activated.

Insert battery pack facing away

from circuit board and fasten

cover with the smallest screws

(provided).

NOTE: Ensure the batteries do

not touch the circuit board and

the antenna and battery wires

are not pinched.

Overview

Learn Button

Models CWPIR and CWPIRC

WIRELESS MOTION ALERT SENSOR

The Wireless Alert Sensor is a Passive Infra-Red (PIR) Motion Sensor that detects movement of people and vehicles, while allowing

small animals to pass through undetected. Each sensor has its own unique ID, for a secure radio link. The base station (not provided)

can learn the signals of up to 8 sensors. The base station gives a single beep for the ﬁ rst sensor that is programmed, a double beep for

the second, and so on. Additionally, multiple base stations can work with the same sensor to sound in different places.

Assembly & Programming

PIR MOTION SENSOR INSTALLATION

Mount PIR Motion Sensor

horizontally on solid surface

3-5 feet (1-1.5 m) off the

ground and within 1/2 mile

(0.8 km) of Base Station (rotate

sensor to access screw holes).

Unit should be able to swivel as

needed.

Attach sun/rain shield.

NOTE: Keep PIR Motion

Sensor antenna away from

metal objects. Do not mount

PIR Motion Sensor in direct

sunlight, near moving tree

branches, or in the path of a

sprinkler system.

4 feet (1.2 m)

10-20 feet (3-6 m)

Vehicle Alert Installation: For cars, the best mounting position

is about 4 feet (1.2 m) high, between 10-20 feet (3-6 m)back,

and angled to see the back of car after passing the sensor.

Troubleshooting

The PIR Motion Sensor lights up, but the Base Station does

not respond.

The PIR Motion Sensor must be programmed to Base Station

(See Step 3). Ensure Base Station is on and the volume is

turned up.

PIR Motion Sensor is detecting motion only part of the time.

Ensure the PIR Motion Sensor is set to the High Sensitivity

setting (See Step 2). To detect cars, it is best to mount PIR

Motion Sensor at height of car’s motor and have it between

10-20 feet (3-6 m) from the road. Swivel sensor as needed.

The Alert is giving false alarms.

Check for moving tree branches or insects in sensor window.

PIR Motion Sensor can also be triggered by light shining

directly in sensor window, such as reﬂ ected sunlight, or motion

in front of a light source.

It is possible that condensation has built up on the sensor. Wipe

condensation from PIR Motion Sensor with cotton swab. Let it

sit inside for a few hours, open to the air, without the batteries

and it should correct itself.

Check Sensor Switches on PIR Motion Sensor. See Switch

Settings.

Base Station beeps every 30 minutes.

The batteries in the Base Station or the PIR Motion Sensor(s)

are low. Replace the 4 AA batteries. Check the PIR Motion

Sensor(s), if the LED illuminates on all of the PIR Motion

Sensors, change the batteries in the Base Station.

The Alert is not getting expected transmission range.

Keep both antennas vertical and keep PIR Motion Sensor

antenna away from trees and metal objects. Ensure Base Station

is in clearest possible sight of the PIR Motion Sensor. The less

objects between the devices, the longer the range.

NOTE: The manufacturer is not responsible for any radio or

TV interference caused by unauthorized modiﬁ cations to this

equipment. Changes or modiﬁ cations not expressly approved

by the manufacturer could void the user’s authority to operate

the equipment.

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this

receiver and/or transmitter are prohibited, except for changing the code setting or replacing the

battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:

1-800-528-9131

www.chamberlain-DIY.com

Product specificaties

Merk:	Chamberlain
Categorie:	Bewegingsdetector
Model:	CWPIR
Kleur van het product:	Grijs
Connectiviteitstechnologie:	Draadloos
Montagewijze:	Muur
Type beeldsensor:	Passieve infraroodsensor (PIR)
Maximumbereik:	9.144 m
Type batterij:	AA
Detectie hoek:	120 °