CDA KVF21RSS Handleiding

CDA Spoelbak KVF21RSS

Lees hieronder de 📖 handleiding in het Nederlandse voor CDA KVF21RSS (4 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

www.cda.eu

KVF21 & KVF22

Stainless Steel

Flush Mount Sinks

Installation

Before Installation

Thoroughly check the sink and any ﬁttings for signs of transport (or

other) damage. Please note: After ﬁtting, sinks cannot be returned for

credit or replacement.

Oer up the sink to the worktop and/or the cabinets to conﬁrm that

the external dimensions of the bowls are compatible with the cabinets

themselves.

Conﬁrm that with the sink in position:

• There is adequate space to install any taps or other required

accessories.

• There is adequate space to install the waste pipe work and that any

necessary modiﬁcation to internal shelves to accommodate the waste

(and trap) is acceptable.

• Access to any water stop-cock or other services will still be adequate

after the installation.

Installation

• Refer to the cut-out sizes on the back of this manual and use them

to mark out where the worktop needs to be cut. Double-check the

dimensions before cutting the worktop aperture.

• After cutting out the worktop aperture, we recommend you seal the

cut edges with silicone (or similar) sealant to help prevent ingress of

water.

• It is often easier to mount the taps, waste-ﬁtting and overﬂow onto the

sink prior to ﬁtting the sink to the worktop.

• The edges of the sink should be bedded onto a bead of silicone

(or similar) sealant, to create a barrier to the ingress of water and

E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the

right to change speciﬁcations without prior notice.

other items between sink and

worktop.

• After positioning the sink on the

worktop, position the ﬁxing brackets

as shown in Fig. 1, then tighten their

screws.

• Do not use a power tool to tighten

the screws; by using a hand tool

it is easier to ensure that they are

tightened just enough to clamp

down on the worktop and no more.

• After ﬁxing, ensure the sealant forms a continuous bead to prevent

water ingress.

• Remove any excess sealant using an appropriate method as

recommended by the sealant manufacturer.

• The taps, waste-ﬁtting and overﬂow can now be mounted onto the

sink (if not already done) and fully connected to their respective

services.

• To check the waste for leaks, close the plug/basket of the waste

ﬁtting, open the tap and ﬁll the sink to the level of the overﬂow; turn

o the tap and wait several minutes to verify that the water doesn’t

drain away.

• Empty the sink.

After ﬁtting, ensure that the enclosed “Stainless Steel Sinks Use and

Maintenance” guide is retained for the customer and/or user of the

sink.

Fig. 1

Product specificaties

Merk:	CDA
Categorie:	Spoelbak
Model:	KVF21RSS
Kleur van het product:	Roestvrijstaal
Breedte:	1000 mm
Diepte:	520 mm
Hoogte:	216 mm
Soort wastafel:	Inbouwspoelbak
Vorm gootsteen:	Rechthoekig
Materiaal gootsteen:	Roestvrijstaal
Aantal gootstenen:	1 kommen
Eerste kom dimensies (WxL):	400 x 195 mm
Kraangat:	Ja
Aanrecht:	Ja
Kraan inclusief:	Nee
Plaats aanrecht:	Rechts