CDA KC73WH Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor CDA KC73WH (4 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
www.cda.eu
Ceramic Sinks
Installation
2
Installation
Before Installation
Oer up the sink to the worktop and/or the cabinets to confirm that
the external dimensions of the bowl are compatible with the cabinets
themselves.
Confirm that with the sink in position:
• There is adequate space to install any taps or other required
accessories.
• There is adequate space to install the waste pipework and that any
necessary modification to internal shelves to accommodate the waste
(and trap) is acceptable.
• Access to any water stop-cock or other services will still be adequate
after the installation.
Cutting the tap hole
Only cut/punch the tap hole from the top face of the sink.
• Select the tap hole position based on whether left hand or right hand
drainer is required.
• Locate the centre of the required tap hole by transferring
measurements from the cast in features on the underside. Cover the
top of the tap hole cut-out area with masking tape.
• Caution: Ensure that the sink is supported under the hole to be cut
out.
• Using a centre punch and hammer, make an initial cut in the glaze at
the centre of the required hole.
• Still using the punch and hammer enlarge the cut to the full hole size
required for the tap by carefully chipping away.
3
E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the
right to change specifications without prior notice.
Installation
• Refer to the cut-out sizes on the back of this manual and use them
to mark out where the worktop needs to be cut. Double-check the
dimensions before cutting the worktop aperture.
• After cutting out the worktop aperture, we recommend you seal the
cut edges with silicone (or similar) sealant to help prevent ingress of
water.
• It is often easier to mount the taps, waste-fitting and overflow onto the
sink prior to fitting the sink to the worktop.
• Position the sink on the worktop, bedding it into a bed of silicone
sealant.
• After positioning the sink, leave it untouched for 24 hours to allow
the sealant to cure before any water is run into it.
• The taps, waste-fitting and overflow can now be mounted onto the
sink (if not already done) and fully connected to their respective
services.
• To check the waste for leaks, close the plug/basket of the waste
fitting, open the tap and fill the sink to the level of the overflow; turn
o the tap and wait several minutes to verify that the water doesn’t
drain away.
• Empty the sink.
After fitting, ensure that the enclosed “Ceramic Sinks Use and
Maintenance” guide is retained for the customer and/or user of the
sink.
Product specificaties
| Merk: | CDA |
| Categorie: | Spoelbak |
| Model: | KC73WH |
Heb je hulp nodig?
Als je hulp nodig hebt met CDA KC73WH stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Spoelbak CDA
5 Juli 2023
2 Juli 2023
20 Juni 2023
20 Juni 2023
19 Juni 2023
18 Juni 2023
16 Juni 2023
16 Juni 2023
15 Juni 2023
15 Juni 2023
Handleiding Spoelbak
- Spoelbak Bartscher
- Spoelbak Blaupunkt
- Spoelbak Franke
- Spoelbak Hendi
- Spoelbak Hotpoint-Ariston
- Spoelbak Leisure
- Spoelbak Rangemaster
- Spoelbak Saro
- Spoelbak Smeg
- Spoelbak Teka
- Spoelbak Concept
- Spoelbak Blanco
- Spoelbak Caple
- Spoelbak Kernau
- Spoelbak Artusi
- Spoelbak Foster
- Spoelbak Nodor
- Spoelbak Elkay
- Spoelbak Gustavsberg
- Spoelbak Schock
- Spoelbak Roca
- Spoelbak Advance Tabco
- Spoelbak Eagle Group
- Spoelbak Sani-Lav
- Spoelbak Fulgor Milano
- Spoelbak Laveo
- Spoelbak Deante
- Spoelbak Tot Mate
- Spoelbak Atosa
- Spoelbak Kuchinox
- Spoelbak Oliveri
- Spoelbak Shaws
- Spoelbak Seima
Nieuwste handleidingen voor Spoelbak
17 December 2024
17 December 2024
16 December 2024
16 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024