CDA KC23WH Handleiding

CDA Spoelbak KC23WH

Lees hieronder de 📖 handleiding in het Nederlandse voor CDA KC23WH (4 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

www.cda.eu

Ceramic Sinks

Installation

Before Installation

Oer up the sink to the worktop and/or the cabinets to conﬁrm that

the external dimensions of the bowl are compatible with the cabinets

themselves.

Conﬁrm that with the sink in position:

• There is adequate space to install any taps or other required

accessories.

• There is adequate space to install the waste pipework and that any

necessary modiﬁcation to internal shelves to accommodate the waste

(and trap) is acceptable.

• Access to any water stop-cock or other services will still be adequate

after the installation.

Cutting the tap hole

Only cut/punch the tap hole from the top face of the sink.

• Select the tap hole position based on whether left hand or right hand

drainer is required.

• Locate the centre of the required tap hole by transferring

measurements from the cast in features on the underside. Cover the

top of the tap hole cut-out area with masking tape.

• Caution: Ensure that the sink is supported under the hole to be cut

out.

• Using a centre punch and hammer, make an initial cut in the glaze at

the centre of the required hole.

• Still using the punch and hammer enlarge the cut to the full hole size

required for the tap by carefully chipping away.

E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the

right to change speciﬁcations without prior notice.

Installation

• Refer to the cut-out sizes on the back of this manual and use them

to mark out where the worktop needs to be cut. Double-check the

dimensions before cutting the worktop aperture.

• After cutting out the worktop aperture, we recommend you seal the

cut edges with silicone (or similar) sealant to help prevent ingress of

water.

• It is often easier to mount the taps, waste-ﬁtting and overﬂow onto the

sink prior to ﬁtting the sink to the worktop.

• Position the sink on the worktop, bedding it into a bed of silicone

sealant.

• After positioning the sink, leave it untouched for 24 hours to allow

the sealant to cure before any water is run into it.

• The taps, waste-ﬁtting and overﬂow can now be mounted onto the

sink (if not already done) and fully connected to their respective

services.

• To check the waste for leaks, close the plug/basket of the waste

ﬁtting, open the tap and ﬁll the sink to the level of the overﬂow; turn

o the tap and wait several minutes to verify that the water doesn’t

drain away.

• Empty the sink.

After ﬁtting, ensure that the enclosed “Ceramic Sinks Use and

Maintenance” guide is retained for the customer and/or user of the

sink.

Product specificaties

Merk:	CDA
Categorie:	Spoelbak
Model:	KC23WH
Kleur van het product:	Wit
Breedte:	1010 mm
Diepte:	510 mm
Hoogte:	225 mm
Soort wastafel:	Opbouwwasbak
Vorm gootsteen:	Rechthoekig
Materiaal gootsteen:	Keramisch
Aantal gootstenen:	1 kommen
Vorm eerste spoelbak:	Rechthoekig
Eerste kom dimensies (WxL):	460 x 405 mm
Eerste kom diepte:	200 mm
Kraangat:	Nee
Aanrecht:	Ja
Kraan inclusief:	Nee
Plaats aanrecht:	Omkeerbaar