CDA KA52SS Handleiding

CDA Spoelbak KA52SS

Lees hieronder de 📖 handleiding in het Nederlandse voor CDA KA52SS (6 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY

T : F : E : 01949 862 012 01949 862 003 customer.care@cda.eu www.cda.euW : www.cda.eu

Stainless Steel

Sinks

Installation

Before installation

Oer up the sink to the worktop and/or the cabinets to conﬁrm that

the external dimensions of the bowls are compatible with the cabinets

themselves.

Conﬁrm that with the sink in position:

• There is adequate space to install any taps or other required

accessories.

• There is adequate space to install the waste pipework and that any

necessary modiﬁcation to internal shelves to accommodate the waste

(and trap) is acceptable.

• Access to any water stop-cock or other services will still be adequate

after the installation.

Installation

• Use the template included with the sink to mark out where the

worktop needs to be cut.

• After cutting out the worktop aperture, we recommend you seal the

cut edges with silicone (or similar) sealant to help prevent ingress of

water.

• Position the supplied gasket around the perimeter of the hole (Fig. 1).

• It is often easier to mount the taps,

waste-ﬁtting and overﬂow onto the sink

prior to ﬁtting the sink to the worktop.

• Ensure that the external edge of the

sink is positioned on the gasket, to

create a barrier to the ingress of water

and other items between sink and

worktop.

Fig. 1

E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the

right to change speciﬁcations without prior notice.

• After positioning the sink on the

worktop, position the ﬁxing brackets

as shown in Fig. 2, then tighten their

screws.

• Do not use a power tool to tighten

the screws; by using a hand tool

it is easier to ensure that they are

tightened just enough to clamp

down on the worktop and no more.

• After ﬁxing, remove any excess gasket material with a suitable

cutter.

• We recommend a thin bead of silicone sealer is applied around the

perimeter as added protection against water ingress.

• The taps, waste-ﬁtting and overﬂow can now be mounted onto the

sink (if not already done) and fully connected to their respective

services.

• To check the waste for leaks, close the plug/basket of the waste

ﬁtting, open the tap and ﬁll the sink to the level of the overﬂow; turn

o the tap and wait several minutes to verify that the water doesn’t

drain away.

• Empty the sink.

After ﬁtting, ensure that the enclosed “Stainless Steel Sinks Use and

Maintenance” guide is retained for the customer and/or user of the

sink.

Fig. 2

Product specificaties

Merk:	CDA
Categorie:	Spoelbak
Model:	KA52SS
Kleur van het product:	Roestvrijstaal
Breedte:	1000 mm
Diepte:	500 mm
Soort wastafel:	Opbouwwasbak
Vorm gootsteen:	Rechthoekig
Materiaal gootsteen:	Roestvrijstaal
Aantal gootstenen:	2 kommen
Vorm eerste spoelbak:	Rechthoekig
Eerste kom dimensies (WxL):	340 x 400 mm
Eerste kom diepte:	180 mm
Vorm tweede spoelbak:	Ovaal
Tweede kom dimensies (WxL):	165 x 290 mm
Tweede kom diepte:	120 mm
Kraangat:	Ja
Aanrecht:	Ja
Kraan inclusief:	Nee
Plaats aanrecht:	Omkeerbaar