Cateye Kosmos CC-ST300 Handleiding

Cateye Fietscomputer Kosmos CC-ST300

Lees hieronder de 📖 handleiding in het Nederlandse voor Cateye Kosmos CC-ST300 (2 pagina's) in de categorie Fietscomputer. Deze handleiding was nuttig voor 144 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

A. Main Display

(Speed)

B. Mode Symbol

C. Speed Scale Symbol

D. Auto Mode Symbol

E. Sub-Display

(Selected Function)

F. Mode Button

G. Start/Stop Button

H. Set Button

I. AC Button

J. Battery Case Cover

K. Contacts

EOPERATING INSTRUCTIONS

1. Bracket

2. Wire

3. Sensor

4. Sensor Bands-A (S)(L)

5. Sensor Bands-B

6. Magnet

7. Sensor Band Rubber Pad

8. Bracket Rubber Pad (2 pcs.)

9. Wire Securing Tape

10. Sensor Band Screw

spoke

BUTTON FUNCTION

• MODE Button (left button)

Changes the display in the order shown in fig. 1, and data is displayed on the sub-

display. *If held over 2 seconds, 24-hour clock appears.

• START/STOP Button (right button)

Starts and stops the measurement of trip distance and elapsed time. During opera-

tion, speed scale symbol flashes. In Auto Function, this button is invalid.

• SET Button

This is for setting the wheel circumference and clock time, switching on/off Auto Func-

tion and to clear all present data and any irregularity. When pressed in stop state in

each mode, the following can be revised.

• In O mode -------------------------- Wheel circumference

• In mode ----------------------- 24-hour clock

• In T, D or A mode ---------------- On/off the Auto function

• AC Button (All Clear)

By pressing AC Button on the back, all data stored ( data, speed scale, wheelO

circumference and clock time) is erased. All displays illuminate, then mile/h sym-

bol illuminates. This operation is to be executed after replacing battery or when ir-

regular display occurs due to static electricity, etc. Since all memories are erased, set

necessary data again according to “Main Unit Preparation”.

Reset Operation: (Fig. 2)

Select any mode except , then press MODE Button and START/STOP Button si-O

multaneously. M, , A D and T will become zero. (When done in O, registered wheel

circumference will be displayed.)

MAIN UNIT PREPARATION

The following must be completed before operating.

(1) How to measure wheel circumference (L) of your bike (Fig. 3)

Put a mark on the tire tread and ride the bike one full wheel revolution. Mark the start

and the end of the revolution on the ground and then measure the distance between

the two marks. This is your actual circumference. Or, the "Selecting Values Cross

Reference Table" tells you an approximate circumference according to tire size.

(2) Setting Speed Scale (Fig. 4)

By pressing AC Button (All Clear Operation), all displays illuminate, and then mile/h

symbol illuminates (fig.4). Km/h and mile/h are alternately displayed with each press

of Start/Stop Button. Press Set Button to set desired speed scale; then the display will

change as fig.5.

(3) Setting the wheel circumference (Fig. 5)

The wheel circumference of 2155mm (standard circumference for 27” wheel) is dis-

played. When using 2155mm without revision, press Set Button. Speed/Elapsed

Time T will be displayed and 2155mm is set. For revision, press Start/Stop Button to

increase the number and Mode Button to decrease. To increase/decrease rapidly,

hold down respective buttons. When the desired number appears, press Set Button;

Speed/Elapsed Time will be displayed and the number is set.T

(4) Resetting or changing the wheel circumference

Set main unit in with MODE Button, and stop it with START/STOP Button. PressO

SET Button. The stored number will flicker on the sub-display. Revise the number as

desired according to the instructions in (3).

Setting the clock time (Fig. 6)

Press MODE Button over 2 seconds to select , and stop it with START/STOP

Button. Then press SET Button, and minutes flash. Press START/STOP Button to

advance minutes by one. To advance rapidly, hold down the button. Set the time one

or two minutes ahead of the current time. Then press MODE Button, and hours will

flash. Use START/STOP Button the same way. Press SET Button to complete time

setting. *When you press the SET Button, the undisplayed seconds will turn to zero.

For accuracy, set by the radio time signal.

MOUNTING TO BIKE

• Attach the magnet on the right spokes of front wheel as fig.7. The spokes must run

correctly through the inside the magnet as in fig.7.

• Attach the sensor with Sensor Bands-A -B to the right fork. Choose a band that fits

the fork diameter (S size for up to 24ø, L for oversize).

1. Insert the band-B into the slit of the band-A , and put the rubber pad inside of the

band-A (fig. 8). Adjust the length in order that the screw-fastening part of the

bands are parallel when mounted to the fork (fig. 9). *To pull out the band B from

band A , tug strongly.

2. Mount the adjusted bands to the fork along with the sensor , by temporarily

tightening the screw (fig. 10).

3. Align the magnet's center and the sensor's marking line (fig. 11), and make sure

of 2mm clearance between the magnet and sensor (fig. 12). Then tighten the

screw securely. Cut the excess of the band-B with a nipper or the like.

• Secure the wire with tape as fig. 13. Wind the wire round the outer cable and adjust

length. Loosen the wire in the area marked with the arrow so that the wire does not

hinder handlebar operation.

• Use either 1mm- or 2 mm-thick pads if necessary, according to handlebar diameter.

Attach the bracket close to the handlebar stem (fig. 14).

• Slide main unit onto the bracket from front until it clicks into position. To remove,

pull it off forward while pushing down the lever . (fig. 15)

•Test

Mount main unit. Lift the front wheel off the ground and spin it to check if the speed is

displayed. If not, adjust the position of magnet and sensor again.

How to replace the battery

Turn main unit over, remove battery case cover with coin and insert a new lithium

battery properly (CR2032) with the (+) pole upward (fig.16), and close the cover se-

curely.

*After replacing battery, be sure to press AC Button and set necessary data again.

Fig.1

Reset

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Spoke

magnet

Fig.7-1

Fig.7-2

sensor band-B

rubber pad

sensor band-A

sensor band-B

rubber pad

Parallel

Fig.9

Fig.8

front fork

sensor screw

Fig.10

marking

line

magnet's

center

Fig.11

sensormagnet

about 2 mm

Fig.12

outer cable

wire wire securing

tape

Fig.13

screw cap

rubber pad

Fig.14

bracket

slide

lever

Fig.15 front

OPEN CR2032

Fig.16

TROUBLE SHOOTING

• The following situations do not indicate malfunction of the cyclocomputer. Check the following before taking to repair.

* When current speed does not appear, short-circuit the contact on the back with metal. The unit will function

normally if the speed display appears.

Display response is slow.

------------- Is it at a low temperature under 32°F(0 C)?°

------------- It returns to normal state when temperature rises.

No display.

------------- Has the Lithium Battery in the main unit worn out?

------------- Replace the Lithium Battery with a new one.

Incorrect data appear.

------------- Execute "All Clear" operation.

Current speed does not appear.

------------- Is there anything on the contact of the main unit or of the bracket?

------------- Wipe the contact clean.

------------- Is the distance between sensor and magnet too far?

------------- Are the marking line of the sensor and the center of magnet matched each other?

------------- Refer to "Sensor/Magnet Mounting" and re-adjust correctly.

------------- Is the wire broken?

------------- Replace the Bracket & Sensor part with a new one.

Transmission signal loss in damp or wet conditions.

------------- Water or condensation may collect between the bracket sensor and the computer causing an

interruption in the data transmission. Wipe the contacts with dry cloth. Contacts can also be treated

with a water repellent silicon jell from an automotive parts or hardware store. Do not use industrial

water repellent; it may damage the bracket.

When the START/STOP Button is pressed, the unit doesn't activate or stop.

------------- Is the unit in the Auto function?

------------- The START/STOP Button doesn't function in the Auto function.

MAINTENANCE/PRECAUTIONS

• Do not leave the main unit exposed to direct sunlight when the unit is not in use.

• Do not disassemble the main unit, sensor and magnet.

• Don't pay too much attention to your computer's functions while riding! Keep your eyes on the road and duly

consider to traffic safety.

• Check relative position of sensor and magnet periodically.

• For cleaning, use neutral detergent on soft cloth, and wipe off later with dry cloth. Do not apply paint thinner,

benzine, or alcohol, to avoid damages on the surface.

• If there is mud, sand or the like clogs between the button and the body, the movement of the button may be

disturbed. Softly wash away such objects with water.

Specifications

Applicable Cycle Sizes: 10mm - 2,999mm

Applicable Fork Diameter: 11ø - 36ø (S:11 - 26ø L:21 - 36ø) The length of the wire: 70cm

Power Supply: Lithium Battery (CR2032 X 1)

Battery Life: Approx. 3 years (The life of the first factory-loaded battery may be shorter than this period.)

Dimension/Weight: 1-15/16" x 1-25/32" x 11/16" (49 x 45 x 17mm) 0.9 oz (25.5 g)

* The specifications and design are subject to change without notice.

MEASURING AND DISPLAY FUNCTIONS

SCurrent Speed

0.0(3.0) - 65.9 mile/h [ 0.3 mile/h under 31 mile/h]±

This is always displayed on the main display and updated once a

second.

OTotal Distance (Odometer) 0.0 - 99,999 mile [±0.1 mile]

This is continuously measured until battery wears down or all clear

operation is done. At 10,000 miles(km), it returns to zero and count-

ing begins anew.

MMaximum Speed 0.0(3.0) - 65.9 mile/h [±0.3 mile/h]

With Reset operation, it returns to zero and counting begins anew.

AAverage Speed 0.0 - 65.9 mile/h [±0.3 mile/h]

The average speed from start to current point is displayed within 27

hours 46 minutes 39 seconds (99,999 seconds) or 999.99 miles

(km). If either is exceeded, (.E) is displayed and calculation ceases.

DTrip Distance 0.00 - 999.99 mile [±0.01 mile]

The trip distance from start to current point is displayed. With Reset

operation, it returns to zero.

TElapsed Time 0:00'00" - 9:59'59" [±0.003%]

Elapsed time is measured from start to current point, in units of

hours, minutes and seconds. At 10 hours, it returns to zero and

counting begins anew. With Reset operation, it returns to zero.

24-hour clock time 0:00' - 23:59' [ 0.003%]±

The current time is displayed by a 24-hour clock.

AUTO (AUTOMATIC START/STOP) FUNCTION

This function switches the main unit to start or stop automatically, in

which

symbol appears on the screen, and you are free from

pressing START/STOP Button each time.

• How to switch on/off the Auto Function.

In , T D or A, this function switches on/off with each press of SET

Button. When on,

symbol appears. *With this function, it

ceases measuring elapsed time during a stop. *2 seconds may be

elapsed if mount the main unit to the bracket with this function on.

POWER SAVING FUNCTION

When main unit is left without receiving any signal for 60-70 minutes

continuously, power supply is shut down and main unit will display

( ) only as the figure. By pressing MODE Button or START/STOP

Button, or by receiving signal, this function is released.

TIRE SIZE L(mm)

dimension du pneu

Radgröße

bandenmaat

dimensione del pneumatico

Tamaño de rueda

タイヤサイズ

700 x 25C 2105

700 x 28C 2136

700 x 30C 2170

700 x 32C 2155

700C Tubular 2130

700 x 35C 2168

700 x 38C 2180

700 x 44C 2224

CO.,LTD.

U.S. Pat. Nos. 4633216/4642606/5236759/5226340 and Design Patented.

CCMST3-970220 0687295 4

CYCLOCOMPUTER

Model CC-ST300

Setting Values Cross Reference Table (The tire size is marked on both sides of the tire.)

Table de Correspondance des Valeurs de Réglage

(La dimension du pneu figure de chaque côté du pneu)

Wertetabelle zur Einstellung des Radumfanges

(die Radgröße entnehmen Sie der Aufschrift des Reifens)

Tabel voor het bepalen van de wielomtrek

(de bandenmaat staat vermeld aan beide zijden van de band)

Tabella delle Corrispondenze dei Valori di Regolazione (La dimensione del pneumatico figura su ogni lato del pneumatico)

Tabla de Valores (El tamaño de la rueda está marcado al lado de la llanta)

タイヤ周長ガイド（タイヤサイズは通常タイヤの側面に記載されています）

S p e c i f ic a t i o ns / Cara ct eristiq ues technique s/ / /T e c h n i s c h e d at e n S p ec if i c at ie s

Caratteristiche tecniche/

Especificaciones

/仕様

Controller/

Calculateur

/ /Controler Controleur/ /Elaboratore

Contador

/制御方式 -------- 4-bit 1-chip Microcomputer (Crystal Controlled Oscillator)

Display/

Affichage

/ / / /Anzeige Display Visualizzazione

Pantalla

/表示方式 -------------------------------------------------- Liquid Crystal Display

Sensor/

Détecteur

/ / / /Sensor Sensor Rivelatore

Sensor

/検知方式 ------------------------------------------------------ No-contact magnetic sensor

Operating Temperature Range/

Température d’utilisation

/ / / /zulässige Betriebstemperatur Toegestane temp. Temperatura di utilizzo 使用温

度範囲 ------------------------------------------------------------------------------------------------------------------------- 0°C - 40°C (32°F - 104°F)

LIMITED WARRANTY

1-Year Warranty for Main Unit Only

(Accessories/Attachments and Battery Consumption excluded)

If trouble occurs during normal use, the part of the Main Unit will be repaired or replaced free of charge. The

service must be performed by Cat Eye Co., Ltd. To return the product, pack it carefully and remember to

enclose the warranty certificate with instruction for repair. Please write or type your name and address clearly

on the warranty certificate. Insurance, handling and transportation charges to our service shall be borne by

person desiring service. Address for service:

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan

Attn.: CAT EYE Customer Service Section

Service & Research Address for United States Consumers:

CATEYE Service & Research Center

1705 14th St. 115 Boulder, CO 80302

Phone: 303-443-4595 Toll Free: 800-5CATEYE

Fax: 303-473-0006 e-mail: CatEyeUSA@aol.com

GARANTIE LIMITÉE

1 An de Garantie sur l'Unité Principale Uniquement

(Les accessoires et la pile sont exclus de la garantie)

En cas de problème en cours d'utilisation normale, l'unité principale sera réparée ou remplacée gratuitement. Par Cat Eye Co., Ltd. Lors

du renvoi du produit, il y a lieu de l'emballer soigneusement et de joindre le certificat de garantie avec les instructions de réparation. Les

nom et adresse de l'acheteur doivent figurer de manière lisible sur le certificat de garantie. Les frais d'assurance, de manutention et

d'envoi à notre Service Réparations seront supportés par le demandeur de la réparation.

Adresse Service Réparations:

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan

Attn.: CAT EYE Customer Service Section

BEGRENZTE GARANTIE

1-Jahr-Garantie: Auf den Computer

(Ersatzteile/Zubehörteile sowie Batterie nicht eingeschlossen)

Falls während des normalen Gebrauchs Fehler auftreten, wird das entsprechende Teil kostenlos repariert oder

ersetzt. Die Reparatur muß von CAT EYE Co., Ltd. durchgeführt werden, und das zu reparierende Produkt muß

direkt durch den Händler an CAT EYE Co., Ltd. gesandt werden. Bei der Rückgabe des Gerätes zur Reparatur

packen Sie es sorgfältig anbei. Achten Sie darauf, Ihren Namen und Ihre Anschrift klar und deutlich lesbar auf

die Garantiekarte zu schreiben, damit das Gerät so schnell wie möglich nach Beendigung der notwendigen

Reparatur/Einstellung an Sie zurückgesandt werden kann.

Anschrift bei Garantieansprüchen:

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan

z. H.: CAT EYE Kundendienstabteilung oder wenden Sie sich bitte an den entsprechenden Importeur.

GARANTLEBEPALINGEN

1 jaar garantie, alleen geldig op de computer

(accessoires, aansluitingen en gebruik van batterij uitgezonderd)

Mochten er problemen optreden gedurende normaal gebruik, dan geschiedt reparatie of vervanging kosteloos.

Dit doent door de fabrikant Cateye Co., Ltd. uitgevoerd te worden. Bij terugzending van de computer moet deze

zorgvuldig verpakt worden en dient het garantiebewijs en een beschrijving van het probleem meegezonden te

worden. Vermeld duidelijk uw naam en adres in blokletters of getypt op het garantiebewijs. Verzekerings- ver-

zend- en transportkosten zijn voor rekening van de koper.

Service adres:

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan

ter attentie van: Cateye klantenservice

GARANZIA LIMITATA

1 Anno di Garanzia soltanto sull'Unità Principale

(Gli accessori e la pila sono esclusi dalla garanzia)

In caso di problema durante l'impiego normale, l'unità principale verrà riparata o sostituita gratuitamente da Cat Eye Co., Ltd..

Al momento del ritorno del prodotto occorre imballarlo con cura allegandovi il certificato di garanzia con le istruzioni per le

riparazioni. Il nome e l'indirizzo dell'acquirente devono essere presenti in modo leggibile sul certificato di garanzia. Le spese di

assicurazione, di manutenzione e di spedizione al nostro Servizio Riparazioni saranno a carico del richiedente la riparazione.

Indirizzo Servizio Riparazioni:

2-8-25 Kuwazu, Higashi Sumiyoshi-ku, OSAKA 546, Giappone.

Att:Dipartamento Assistenza Clienti

GARANTIA LIMITADA

Se garantiza por un año únicamente el grupo central

(Los accesorios, aditamentos y el consumo de la pila están excluidos)

Si ocurriera alguna avería durante el uso normal, se reparará o sustituirá la pieza o el grupo central. Cat Eye Co., Ltd. deberá

realizar la reparación. Para devolver el producto, envuélvalo cuidadosamente y no olvide incluir el certificado de garantía y las

instrucciones para repararlo. Rogamos escribir claramente a mano o a máquina su nombre y dirección. Los gastos de seguro,

manipulación y transporte serán a cargo de la persona que solicite la reparación.

Dirección para las reparaciones:

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan

Attn.: CAT EYE Customer Service Section

製品保証について

1 年保証：コンピュータのみ（付属品及び電池の消耗は除く）

正常な使用状態で万一故障した場合は無料で修理・交換いたします。保証書にお客様のお名前・ご住所・ご購入日・

故障状態をご記入の上、製品と共に当社宛て直接お送りください。お送りいただく際の送料はお客様にてご負担

願います。修理完了後、当社より郵送にてお届けさせていただきます。

［宛先］製品サービス課

〒546 大阪市東住吉区桑津2丁目8番25号

TEL: (06)719-2631 FAX: (06)719-2362

＊アクセサリーパーツを別途販売していますのでご利用ください。

#169-6560 (#169-6565)

Bracket Sensor Kit (Long)

Kit Support Unité Principale et Détecteur (Long)

Halterung+Radsensor Ausrüstung für Vorderradmontage (Lang)

Bracket en sensorkitset (Lang)

Element da montare : Supporto Unità principale e Sensore (Largo)

Conjunto de soporte y sensor

ブラケットセンサーキット（ロング）

#169-6567 (#169-6562)

Center Mount Bracket Kit (Long)

Kit de montage central de l'unité principale (Long)

Halterung für Montage an der Lenkermitte (Lang)

Stuurbocht Bevestiging Set (Lang)

Kit di montaggio al centro del manubrio (Lungo)

Kit Soporte pala Montaje Central (Largo)

センターマウントブラケットキット（ロング）

#169-6568

Bracket Sensor Kit for Aero Bar

Kit de Montage du Collier de Détecteur pour Barre Aero

Halterung und Radsensor für Aero-Lenker

Sensor bevestiginset voor Aero Stuurbocht

Kit di Montaggio del Collare del Sensore per Barra Aero

Kit abrazadera de sensor para manillares Aero

エアロバー用ブラケットセンサーキット

#169-6569

Stem Mount Bracket Kit

Kit de montage de l'unité principale sur la broche du guidon

Halterung für Montage an der Lenkerstange

Stuurpen Bevestiging Set

Kit di montaggio sull'attacco manubrio

Kit Soporte pala Montaje en Tija

ステム用ブラケットセンサーキット

#169-9730

Heavy Duty Wire and Bracket Sensor Kit

Kit de Fil Renforce et Supports d'Unité Principale et de Détecteur

Nachrüstset mit Halterung, Sensor und verstärktem Sensorkabel

Extra sterke kabel en bracket sensor set

Filo Ultra Resistente e Attacco Completo

Kit Soporte del Sensor y Alambre de Servicio Pesado

ヘビーデューティワイヤ&ブラケットセンサーキット

#169-6170 #169-6280

Attachment Kit Universal Sensor Band

Kit de Gamitures Garniture Universelle pour Détecteur

Befestigungsmaterial Universal Befestigungsband

Kabelbevestigingset Universele Sensor klemstrip

Guarnizioni da montare Guanizione Universale per Sensore

Elementos de fijación Banda del Sensor Universal

アタッチメントキットユニバーサルセンサーバンド

#166-5120 #166-5150

Wheel Magnet Lithium Battery (CR2032)

Aimant pour roue Pile au lithium (CR2032)

Radmagnet Lithium-Batterie(CR2032)

Wielmagneet Lithum Batterij (CR2032)

Magnete ruota Bateria al Litio (CR2032)

Iman de la rueda Bateria de Litio (CR2032)

ホイールマグネットリチウム電池 (CR2032)

TIRE SIZE L(mm)

dimension du pneu

Radgröße

bandenmaat

dimensione del pneumatico

Tamaño de rueda

タイヤサイズ

20 x 1.75 1491

24 x 1 1753

24 x 3/4 Tubular 1785

24 x 1-1/8 Tubular 1795

24 x 1-1/4 1905

24 x 1.75 1890

24 x 2.00 1925

24 x 2.125 1965

26 x 1(559mm) 1913

26 x 1(650c) 1952

26 x 1.25 1953

TIRE SIZE L(mm)

dimension du pneu

Radgröße

bandenmaat

dimensione del pneumatico

Tamaño de rueda

タイヤサイズ

26 x 1-1/8 Tubular 1970

26 x 1-3/8 2068

26 x 1-1/2 2100

26 x 1.40 2005

26 x 1.50 1985

26 x 1.75 2023

26 x 1.95 2050

26 x 2.00 2055

26 x 2.1 2068

26 x 2.125 2070

26 x 2.35 2083

TIRE SIZE L(mm)

dimension du pneu

Radgröße

bandenmaat

dimensione del pneumatico

Tamaño de rueda

タイヤサイズ

27 x 1 2145

27 x 1-1/8 2155

27 x 1-1/4 2161

27 x 1-3/8 2169

650 x 35A 2090

650 x 38A 2125

650 x 38B 2105

700 x 18C 2070

700 x 19C 2090

700 x 20C 2086

700 x 23C 2096

Product specificaties

Merk:	Cateye
Categorie:	Fietscomputer
Model:	Kosmos CC-ST300

Heb je hulp nodig?

Als je hulp nodig hebt met Cateye Kosmos CC-ST300 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Fietscomputer Cateye

Cateye Commuter CC-COM10W Handleiding

21 December 2024

Cateye Quick CC-RS100W Handleiding

26 Maart 2024

Cateye Padrone+ CC-PA110W Handleiding

26 Maart 2024

Cateye Padrone Digital CC-PA400B Handleiding

26 Maart 2024

Cateye OS 1.1. Handleiding

8 Juni 2023

Cateye Padrone Smart CC-PA500B Handleiding

4 Juni 2023

Cateye e-Train Data IF-TR100 Handleiding

20 Mei 2023

Cateye Padrone Smart plus CC-SC100B Handleiding

13 Mei 2023

Cateye Padrone CC-PA100W Handleiding

10 Mei 2023

Cateye Padrone Smart plus CC-VT235W Handleiding

9 Mei 2023

Handleiding Fietscomputer

Nieuwste handleidingen voor Fietscomputer

Lezyne Micro C Handleiding

15 November 2024

Pro phete BW 020 Handleiding

7 November 2024

Wahoo Elemnt Roam v2 Handleiding

23 September 2024

VDO R4 Handleiding

26 Juli 2024

VDO R5 Handleiding

26 Juli 2024

Sigma Eox View 1700 Handleiding

22 Juli 2024

Aplic 305673 Handleiding

16 Juli 2024

IGPSport BSC100 Handleiding

16 Juli 2024

IGPSport iGS800 Handleiding

15 Juli 2024

Blackburn Delphi 2.0 Handleiding

11 Juni 2024