Cateye Enduro 2 CC-ED200 Handleiding

Cateye Fietscomputer Enduro 2 CC-ED200

Lees hieronder de 📖 handleiding in het Nederlandse voor Cateye Enduro 2 CC-ED200 (4 pagina's) in de categorie Fietscomputer. Deze handleiding was nuttig voor 139 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Setting Values Cross Reference Table (The tire size is marked on both sides of the tire.)

Table de Correspondance des Valeurs de Réglage

(La dimension du pneu ﬁgure de chaque côté du pneu)

Wertetabelle zur Einstellung des Radumfanges

(die Radgröße entnehmen Sie der Aufschrift des Reifens)

Tabella delle Corrispondenze dei Valori di Regolazione

(La dimensione del pneumatico figura su ogni lato del pneumatico)

Tabel voor het bepalen van de wielomtrek (de bandenmaat staat vermeld aan beide zijden van de band)

Tabla de Valores (El tamaño de la rueda está marcado al lado de la llanta)

* The values listed here are not deﬁnitive information. Wheel circumference varies with the tire pressure.

* Les valeurs indiquées sont approximatives. La circonférence de roue varie en fonction de la pression de gonflage du pneu.

* Die angegebenen Zahlen sind nur Näherungswerte. Der Radumfang kann je nach Reifendruck verschieden sein.

* De waarden in de tabel zijn niet exact, de wielomtrek is ook afhankelijk van de bandenspanning en het profiel.

* Las medidas aquí mencionadas no son una información definitiva. La circunferencia del neumático varía con la presión del mismo.

Specifications/Caractéristiques techniques/Technische Daten

Caratteristiche tecniche/speciﬁcaties/

Especiﬁcaciones

Controller/

Systéme de contrôle

/ /Controler Elaboratore/Controller/

Controlador

------------------------------------------------------------------ 4-bit 1-chip Microcomputer (Crystal Controlled Oscillator)

Display/

Afficheur

/ / / /Anzeige Visualizzazione Display

Pantalla

----------------------------------- Liquid Crystal Display

Sensor/

Détecteur

/ / / /Sensor Rivelatore Sensor

Sensor ------------------------------------

No Contact Magnetic Sensor

Operating Temperature Range/

Température d'utilisation

/ / /zulässige Betriebstemperatur Toegestane temp.

Werking temperatuur/

Rango de Temperatura de Funcionamiento ---------------------------------

0 F)°C - 40°C(32°F - 104°

TIRE SIZE

dimension du pneu

Radgröße

dimensione del pneumatico

bandenmaat

Tamaña de rueda

TIRE SIZE

dimension du pneu

Radgröße

dimensione del pneumatico

bandenmaat

Tamaña de rueda

TIRE SIZE

dimension du pneu

Radgröße

dimensione del pneumatico

bandenmaat

Tamaña de rueda

TIRE SIZE

dimension du pneu

Radgröße

dimensione del pneumatico

bandenmaat

Tamaña de rueda

L(cm) L(cm) L(cm) L(cm)

20 x 1.75

24 x 1

24 x 3/4 Tubular

24 x 1-1/8

Tubular

24 x 1-1/4

24 x 1.75

24 x 2.00

24 x 2.125

26 x 1(559mm)

26 x 1(650c)

26 x 1.25

26 x 1-1/8

Tubular

26 x 1-3/8

26 x 1-1/2

26 x 1.40

26 x 1.50

26 x 1.75

26 x 1.95

26 x 2.00

26 x 2.1

26 x 2.125

26 x 2.35

27 x 1

27 x 1-1/8

27 x 1-1/4

27 x 1-3/8

650 x 35A

650 x 38A

650 x 38B

700 x 18C

700 x 19C

700 x 20C

700 x 23C

700 x 25C

700 x 28C

700 x 30C

700 x 32C

700C Tubular

700 x 35C

700 x 38C

700 x 44C

207

209

217

218

222

212

211

207

209

210

211

214

217

216

213

210

200

199

202

205

206

207

208

215

216

217

150

175

178

179

191

189

192

196

191

195

197

#169-9750 #169-6170

Attachment Kit (for CC-ED200) Attachment Kit (for CC-MT300)

Kit de Gamitures (pour CC-ED200) Kit de Gamitures (pour CC-MT300)

Befestigungsmaterial (f r CC-ED200) Befestigungsmaterial (fü ür CC-MT300)

Guarnizioni da montare (per CC-ED200) Guarnizioni da montare (per CC-MT300)

Kabelbevestigingset (voor CC-ED200)

Kabelbevestigingset (voor CC-MT300)

Elementos de ﬁjaci n (para CC-ED200)ó

Elementos de ﬁjaci n (para CC-MT300)ó

#169-9730

Heavy Duty Wire and Bracket Sensor Kit

Kit Fil Renforc , Support et Dè étecteur

Draht und Halterung/Sensor-Kit f r starke Beanspruchungü

Kit supporto dell unit principale e sensore’ à

Dikke draad- en bracketset

Cable resistente y Kit Soporte del Sensor

#166-5150

Lithium Battery (CR2032)

Pile au Lithium (CR2032)

Lithiumbatterie (CR2032)

#169-6568

Bracket Sensor Kit for Aero Bar

Kit Support et D tecteur pour Barre Aé éro

Halterung/Sensor-Kit f r Aero-Stangeü

Kit supporto sensore per ruote Aero

Draadset stuurpen bevestiging

Kit Soporte del Sensor para Manillar Aero

#169-6567 [#169-6562]

Center Mount Bracket Kit [Long]

Kit Support pour Montage Central [Long]

Halterungskit für Mittelmontage [lang]

Kit per montaggio del ciclocomputer al centro del manubrio [Lungo]

Draadset centrale bevestiging [lang]

Kit Soporte para Montaje Central [Grande]

#169-9751 #169-6280

Attachment Kit (For Extra Large Fork) Universal Sensor Band

Kit de Gamitures (Pour fourche extra large) Collier Détecteur Universel

Befestigungsmaterial (F r besonders groü ß üe Gebeln) Universalmontageband f r Sensor

Guarnizioni da montare (Per forcelle "extra large") Fascetta universale per ﬁssaggio sensore

Kabelbevestigingset (Voor extra dikke vork) Universele vorkklem

Elementos de fijaci n (Para horquilla extra larga)ó

Banda Sensor Universal

#169-6569

Stem Mount Bracket Kit

Kit Support pour Montage sur Broche de Guidon

Halterungskit für Montage am Lenkerschaft

Kit per montaggio sull'attacco del manubrio

Draadset stuurpen bevestiging

Kit Soporte para Montaje en Potencia

#169-6560 [#169-6565]

Bracket Sensor Kit [Long]

Kit Support et D tecteur [Long]é

Halterung/Sensor-Kit [lang]

Kit supporto dell'unit principale e sensore [Lungo]à

Draadset [lang]

Kit Soporte del Sensor [Grande]

#169-9770

Bracket Sensor Kit for Extra Large Fork

Kit de Montage du collier de D tecteur pour fourcheextra largeé

Halterung und Radsensor f r besonders gro e Gabelnü ß

Kit di Montaggio del collare del Sensore per forcelle "extra large"

Sensor bevestiginset voor extra dikke vork

Kit abrazadera de sensor para horquilla extra larga

CATEYE VELO 2

CYCLOCOMPUTER

CC-VL200

CAT EYE ENDURO 2

CAT EYE MITY 3

CYCLOCOMPUTER

CC-ED200 [with Heavy Duty Wire]

CC-MT300 [with Normal Wire]

U.S. Pat. Nos. 4633216/4642606/5236759/5226340/5264791

Pat. and Design Pat. Pending

CCMED2/MT3-981116 Printed in Japan 0687460

Wheel Magnet

Aimant de Roue

Radmagnet

Magnete per ruota

Wielmagneet

Imán de Rueda

Wheel Magnet for Composit Wheel

Pour roue composite

Für Verbundräder

Magnete per ruote

Voor o.a, carbonwielen

Para rueda de palos

#169-9760 #166-5120

Batteria al litio (CR2032)

Lithiumbatterij (CR2032)

Batería de Litio (CR2032)

LIMITED WARRANTY

1-Year Warranty for Main Unit Only

(Accessories/Attachments and Battery Consumption excluded)

If trouble occurs during normal use, the part of the Main Unit will be repaired or replaced free of charge. The service must

be performed by Cat Eye Co., Ltd. To return the product, pack it carefully and remember to enclose the warranty certifi-

cate with instruction for repair. Please write or type your name and address clearly on the warranty certificate. Insurance,

handling and transportation charges to our service shall be borne by person desiring service.

(Address for service)

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Attn.: CAT EYE Customer Service Section

Service & Research Address for United States Consumers:

CAT EYE Service & Research Center

1705 14th St. 115 Boulder, CO 80302

Phone : 303-443-4595 Toll Free : 800-5CATEYE

Fax : 303-473-0006 e-mail : CatEyeUSA@aol.com

GARANTIE LIMITEE

1 An de Garantie Unité Principale Uniquement

(à l'exclusion des accessoires et de la pile)

Ce produit est garanti, sous r serve d'une utilisation normale, pendant une p riode d'un an. Les r parations effectu es dans le cadre de laé é é é

présente garantie sont gratuites et doivent être effectuées par CAT EYE Co., Ltd. Le produit à réparer doit être retourné à CAT EYE Co.,

Ltd. directement par l'acheteur. Tout produit retourn au d partement de r paration CAT EYE doit tre soigneusement emball et leé é é ê é

certificat de garantie ainsi que les instructions de r paration doivent accompagner le produit. Il est conseill l'acheteur d' crire lisiblementé é à é

ou de dactylographier ses nom et adresse sur le certificat de garantie, afin que le produit lui soit directement retourn apr s ré è éparation.

Le co t de l'assurance ainsi que les frais de manutention et de transport sont paration sous garantie.û à charge de la personne souhaitant une ré

(Adresse d'envoi pour réparation)

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japon

Attn. : CAT EYE Customer Service Section

GARANTIE

1 Jahr Garantie nur auf den Computer

(Die Zubehör-/Montageteile und Batterie sind von Garantieleistungen ausgeschlossen)

Falls w hrend des normalen Gebrauchs Fehler auftreten, wird das entsprechende Teil des Computers kostenlos repariert oder ersetzt.ä

Die Reparatur muß von Cat Eye Co., Ltd durchgef hrt werden. Wenn Sie das Ger t einsenden, packen Sie es sorgf ltig ein und fü ä ä ügen

Sie die Garantiekarte sowie Reparaturhinweise anbei. Achten Sie darauf, Ihren Namen und Ihre Anschrift mit Schreibmaschine oder

in Druckbuchstaben deutlich lesbar auf die Garantiekarte zu schreiben. Versicherungskosten und Kosten f r den Transport bis zuü

unserem Kundendienst gehen zu Lasten der Person, die unseren Kundendienst in Anspruch nehmen m chte.ö

(Anschrift des Kundendienstes)

2-8-25 Kuwazu, Higashi Sumiyoshi-ku, Osaka, 546-0041 Japan

Attn.: CAT EYE Customer Service Section

GARANZIA LIMITATA

1 Anno di Garanzia soltanto sull'Unità Principale

(Gli accessori e la pila sono esclusi dalla garanzia)

In caso di problema durante l'impiego normale, l'unit principale verr riparata o sostituita gratuitamente da Cat Eye Co., Ltd.. Alà à

momento del ritorno del prodotto occorre imballarlo con cura allegandovi il certificato di garanzia con le istruzioni per le ripara-

zioni. Il nome e l'indirizzo dell'acquirente devono essere presenti in modo leggibile sul certificato di garanzia. Le spese di

assicurazione, di manutenzione e di spedizione al nostro Servizio Riparazioni saranno a carico del richiedente la riparazione.

(Indirizzo Servizio Riparazioni)

2-8-25 Kuwazu, Higashi Sumiyoshi-ku, OSAKA 546-0041, Giappone.

Att:Dipartamento Assistenza Clienti

GARANTLE BEPALINGEN

1 jaar garantie op de computer unit

(bedrading, magneet, sensor, batterij en bevestigingsmateriaal uitgezonderd)

Indien er problemen optreden gedurende normaalgebruik, binnen de garantie periode, dan geschiedt reparatie of vervanging kosteloos.

Dit dient door de fabrikant Cat eye Co. Ltd. uitgevoerd te worden. de computer moet door de importeur terug gezonden worden. Bij

terugzenden van de computer moet deze zorgvuldig verpakt worden en dient het garantie bewijs, de aankoopbon en een beschrijving

van het probleem meegezonden te worden. Verzekering- en verzend- en transportkosten zijn voor rekening van de koper.

(Service adres)

2-8-25, Kuwazu, Higashi Sumiyoshi-Ku, Osaka 546-0041 Japan

Attn.: Cat eye consumer service section

GARANTÍA LIMITADA

1- Año de Garantía Sólo para la Unidad Principal

(Se excluyen Accesorios/Acoplamientos y Batería)

En caso de problemas durante su uso normal, la unidad principal será reparada o reemplazada sin coste alguno. El servicio

debe ser realizado por el distribuidor CAT EYE en su pa n, empaquís. Para enviar el producto al servicio de reparació ételo

primero cuidadosamente y no olvide incluir el certificado de garant a e instrucciones para el servicio de reparaci n. En elí ó

certificado de garant a deber constar su nombre y direcci n y transporte oí á ón completa. Los gastos de seguro, manipulació

correo deber n correr a cargo de quien solicite dicho servicio.á

(Dirección para las reparaciones)

2-8-25, Kuwazu, Higashi Sumiyoshi-Ku, Osaka 546-0041 JAPAN

ATT: CAT EYE Customer Service Section

CO.,LTD.

When is oﬀ:

When is on:

SET (on back)

SMODE

Switches on/off

Moves between wheel

circumference and

Moves to the next function

Shifts Tm/ /Av Mx data to

the upper display

Starts/stops measuring

Shifts Tm/ /Av Mx data to the upper display

(How the display changes

by MODE button)

Av Mx

Dst1 Dst2 Odo

In Tm, Av and displayDst(1, 2)

SET (on back)

SMODE

Completes setting Ready for measuring

Moves between wheel circumference A and B

Increases the figure by one

Rapidly increases the figure

Decreases the figure by one

Rapidly decreases the figure

SET (on back)

SMODE

Completes setting

Ready for measuring

Increases the ﬁgure by one

Rapidly increases the ﬁgure

Moves from hour digits

to minute digits

SET (on back)

S MODE

Press all

the three buttons

simultaneously.

In Wheel Circumference Setting Display:

If SET button is pressed in display (stop state),Odo

wheel circumference setting display appears.

In Clock Time Setting Display:

If SET button is pressed in (stop state), clock time setting dis-

play appears.

In Measuring Functions:

When measuring, the speed scale ﬂashes.

All Clear Operation

Precautions

• Don't pay too much attention to your computer functions while riding. Keep your eyes on

the road and pay attention to traffic conditions.

• Securely attach the magnet, sensor and bracket to your bicycle. Periodically check if the

screws and secure bands have loosened.

• Safely dispose of the old battery. Do not place it within children's reach. If swallowed by

mistake, consult a doctor immediately.

• Do not leave the main unit exposed to direct sunlight. Never disassemble the main unit.

• For cleaning, use neutral detergent on soft cloth, and wipe off with dry cloth. Do not

apply paint thinner, benzine or alcohol, to avoid damages on the surface.

• If there is mud, sand or the like clogged between the button and the body, button opera-

tion can become impaired. Softly wash away such objects with water.

• Before each ride, insure the computer is completely and securely mounted to the

bracket.

A. Upper Display

(Usually Current Speed)

B. Mode Symbol

C. Average Pace Arrow

D. Speed Scale

E. Auto Mode Symbol

F. Wheel Selection Symbol

G.Lower Display

(Selected Function)

H. Mode Button

I. S Button (Start/Stop)

J. SET Button

K. Battery Cover

L. Contact

HOW TO ATTACH TO BICYCLE

All Clear Operation

Press all the three buttons simultaneously.

All displays illuminate, and then " " symbol ﬂashes.K

Speed Scale Selection

Press MODE button and select "K"(=km) or "M"(=mile).

Wheel Circumference Setting

Input wheel circumference A

by S button ( ) or MODE button (+).–

For inputting wheel circumference B, hold down SET button;

the display changes to B. Input the ﬁgure in the same way.

Press S or SET button to ﬁx it

Press SET button to ﬁx it

Preparation Completed

Set the Clock time

Odo Data Input

Hold down MODE button to reach input display.Odo

Input the ﬁgure by MODE button.

Press S button to change the ﬂickering digit.

Refer to the "Installation Manual".

MAIN UNIT PREPARATION

Using this unit

for the ﬁrst time

After

replacing battery

Spd Current Speed

Wheel A: 0.0(3.0)-65 mph 1 mph(under 31 mph)[0.0(4.0)-105km/h ± ±1km/h]

Wheel B: 0.0(2.0)-65 mph 1 mph(under 31 mph)[0.0(2.5)-105km/h ± ±1km/h]

Usually displayed on the upper display and updated once a second. When Av

or Mx data is shifted to the upper display, Spd shifts to the lower display.

Average Pace Arrow

Shows whether the current speed is faster or slower than the average

speed. ------Faster than the average speed

------Slower than the average speed

When the average speed is zero, or when in the stop state, no pacer

symbol appears.

Odo Total Distance (Odometer)

0.0 - 9999.9 /10000 - 99999 mile[km] 0.1 mile[km]±

Continuously measured until battery wears down. Displayed with 0.1

resolution up to 9999.9 km and with 1.0 resolution up to 99999 km. (With

all clear operation, it returns to zero; to continue accumulation of data,

input the previous Odo data after all clear operation.)

Dst(1, 2) Trip Distance(1, 2)

0.00 - 999.99 mile[km] 0.01 mile[km]±

The trip distance from start to current point is displayed. Two different

start points can be set (Dst1 and Dst2). Dst2 is best for measuring a sec-

tional distance. With Reset operation, it returns to zero. [Reset of Dst1 is

always done with reset of Tm, Av and Mx all together. Reset of Dst2 is

done independently of the other reset and does not affect the other data.]

Tm Elapsed Time

0:00'00" - 9:59'59" ±0.003 %

Elapsed time is measured from start to current point, in units of hours,

minutes and seconds. At 10 hours, it returns to zero and counting begins

anew. With the press of S button, Tm data shifts to the upper display. In

this case, the lower display shows the hour digits of Tm data (instead of

Spd). With Reset operation, it returns to zero.

Av Average Speed

0.0 - 65 mph [105 km/h] 0.3 mph [km/h]±

The average speed from start to current point is displayed. If the elapsed

time exceeds 27 hours or Dst1 exceeds 999.99km, (.E) is displayed and

calculation ceases. With the press of S button, Av data shifts to the upper

display. In this case, Spd data is shifted to the lower display. With reset

operation, it returns to zero.

Mx Maximum Speed

0.0(3.0) - 65 mph [105 km/h] 1 mph [km/h]±

Displays the highest recorded speed. With the press of S button, Mx data

shifts to the upper display. In this case, Spd data is shifted to the lower

display. With reset operation, it returns to zero.

Clock time

1:00' - 12:59' or 0:00' - 23:59' ±0.003 %

If "M" is selected for speed scale, the clock time is in 12 hour. If "K", the

clock time is 24 hour.

Automatic Start/Stop Function

When the symbol is on, the unit automatically starts and stops measuring while a wheel

pulse is detected. (See the above In Measuring Functions for how to switch on/oﬀ “ ” .)

Power Saving Function

When the main unit does not receive a signal, or a button has not been pressed for 60-70

minutes, the power supply is shut down and the main unit will only display the clock. By

pressing either MODE or S button, or by receiving signal, this function is released.

Maintenance

When the main unit or the contact gets wet, dry it off with a cloth; rust will cause functional

errors.

Trouble Shooting

No display.

Has the battery in the main unit worn out?

Replace it with a new one.

Incorrect data appears or the screen is frozen.

Do "All Clear" operation. (If possible, write down the Odo data before all clear opera-

tion, and input it again after the display returns normal.)

Current speed does not appear. (When current speed does not appear, first short-circuit the

contact on the back with metal; if the speed display appears, the main unit is normal and the

problem must be in the bracket or the sensor.)

Is there anything on the contact of the main unit or of the bracket?

Wipe the contact clean. DO NOT use abrasives, sandpaper, etc.

Is the distance between the sensor and the magnet too far?

Are the marking line of the sensor and the center of magnet aligned?

Adjust the position of the sensor and magnet again.

Is the wire broken?

Replace it with a new one.

When "M" (=Mile) was chosen for speed

scale, the clock time is in 12-hour. If "K"

(=Km), the clock time is 24-hour.

How to Replace Battery

Insert a new lithium battery (CR2032) with the (+) pole upward. Per-

form ALL CLEAR OPERATION after replacing the battery.

In order to continue accumulation of Odo data, write down the stored

Odo before replacing the battery.

Continuing Accumulation of Odo Data

Although the Odo data returns to zero by all clear operation, you can

continue accumulation of data by inputting the previous Odo data.

Be sure to write down the data before replacing the battery.

Specifications

Applicable Wheel Circumference --- 100cm - 300cm

Applicable Fork Diameter ------------ ED200; 11ø to 40ø (Sensor Band S: 11-26ø, Sensor Band L: 21-40ø)

---------------------------------------------- MT300; 11ø to 36ø (Sensor Band S: 11-26 , Sensor Band L: 21-36ø ø)

Length of Wire -------------------------- 70cm

Power Supply ---------------------------- Lithium Battery (CR2032) x 1

Battery Life ------------------------------- Approx. 3 years

(The life of the first factory-loaded battery may be shorter than this period.)

Dimension/Weight ---------------------- 1-13/16” x 1-17/32” x 9/32” [46 x 39 x 17mm] / 0.92 oz [26 g]

* The specifications and design are subject to change without notice.

Wheel circumference setting is the

actual distance in centimeters on

the ground of one wheel revolution

measures. For the most accurate

settings, do this roll-out. Otherwise,

consult the Cross Reference Table

for approximate setting.

Tm moves up as

Main Display

Av moves up as

Main Display

Mx moves up as

Main Display

SET

Dst1 Dst2

Just press

Hold down

(2 sec.)

Button Operation

Reset Operation

Data to be reset:

In Tm, Av, Mx, Dst1 and display:

---- Resets Tm, Av, Mx and Dst1 data all together

In Dst2 display: -------------- Resets only Dst2 data

S MODE

Press S and MODE buttons

simultaneously for 1 second

Open

OPERATING INSTRUCTIONS

Wheel Circumference A & B

(Can switch between A & B any time)

A: Best for road bikes and riding [Initial figure =210 cm]

B: Best for MTB riding and low speed sensitivity

[Initial figure =205 cm]

When MODE button and S button are pressed

simultaneously in display, first the wheelOdo

circumference value appears. If these buttons are

further held down for more than 3 seconds, the wheel

circumference moves between A or B.

(2)

(1)

(2)

(1)

2mm

(3)

(4)

1 4

CAT EYE MITY3

CC-MT300

1Bracket

2Wire

3Sensor

4Sensor Bands-A

5Sensor Band-B

6Magnet

7Sensor Band Rubber Pad

8Bracket Rubber Pad

9Nylon Tie

0Sensor Band Screw

Attach the sensor temporarily.

Note: Sensor Band-A

(Small) --------- 11Ø-26Ø

(Large) --------- 21Ø-36Ø

Align the magnet's center(1) and the

sensor's marking line(2). Make sure of

approx. 2mm clearance between the magnet

6 3 and sensor .

Test

Slide the main unit onto the bracket according to " How to Attach Main Unit to

Bracket" (below). Make sure the computer is fully attached to the bracket. Spin the

front wheel and check if the speed display appears. (If not, adjust the relative posi-

tions of magnet and sensor again.) Fasten the sensor securely, and remove the

main unit.

Secure the wire along the fork with the

nylon ties , and wind it round the brake9

cable(3) up to the handlebar.

Note: Allow enough wire length in the

area marked with in the illus-

tration, to insure full movement

and unhindered operation of the

handlebar.

Test the alignment of the magnet and sensor with the main unit attached.

How to Attach Main Unit to

Bracket

Slide main unit onto the bracket from front until

it clicks into position. To remove, pull it off for-

ward while pushing down the lever(4).

Product specificaties

Merk:	Cateye
Categorie:	Fietscomputer
Model:	Enduro 2 CC-ED200

Heb je hulp nodig?

Als je hulp nodig hebt met Cateye Enduro 2 CC-ED200 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Fietscomputer Cateye

Cateye Quick CC-RS100W Handleiding

26 Maart 2024

Cateye Padrone+ CC-PA110W Handleiding

26 Maart 2024

Cateye Padrone Digital CC-PA400B Handleiding

26 Maart 2024

Cateye OS 1.1. Handleiding

8 Juni 2023

Cateye Padrone Smart CC-PA500B Handleiding

4 Juni 2023

Cateye e-Train Data IF-TR100 Handleiding

20 Mei 2023

Cateye Padrone Smart plus CC-SC100B Handleiding

13 Mei 2023

Cateye Padrone CC-PA100W Handleiding

10 Mei 2023

Cateye Padrone Smart plus CC-VT235W Handleiding

9 Mei 2023

Cateye Velo Wireless Handleiding

5 Mei 2023

Handleiding Fietscomputer

Nieuwste handleidingen voor Fietscomputer

Lezyne Micro C Handleiding

15 November 2024

Pro phete BW 020 Handleiding

7 November 2024

Wahoo Elemnt Roam v2 Handleiding

23 September 2024

VDO R4 Handleiding

26 Juli 2024

VDO R5 Handleiding

26 Juli 2024

Sigma Eox View 1700 Handleiding

22 Juli 2024

Aplic 305673 Handleiding

16 Juli 2024

IGPSport BSC100 Handleiding

16 Juli 2024

IGPSport iGS800 Handleiding

15 Juli 2024

Blackburn Delphi 2.0 Handleiding

11 Juni 2024