Casio G-Shock G-Steel GST-410-1AER Handleiding

Casio Horloge G-Shock G-Steel GST-410-1AER

Lees hieronder de 📖 handleiding in het Nederlandse voor Casio G-Shock G-Steel GST-410-1AER (5 pagina's) in de categorie Horloge. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

Operation Guide 5553

E-9

To set the time and date

1. In the Timekeeping Mode, hold down A for about two

seconds until “SET” appears on the lower display. This

is the setting mode.

• Note that keeping A depressed too long (for about

five seconds) will cause a different type of setting

mode to be entered (page E-33).

2. Use D and B to select the city code you want.

• Make sure you select your Home City code before

changing any other setting.

• For full information on city codes, see the “City Code

Table” at the back of this manual.

City code

E-8

Timekeeping

You can adjust the Home Time city date and time in the Timekeeping Mode.

• Pressing A in the Timekeeping Mode will toggle lower display between the

screens shown below.

Home City Date Home City Time

Day of the week Day of the week

Date PM indicator

Hour : Minutes

SecondsSeconds

E-7

Alarm Mode (page E-24)

Countdown Timer Mode (page E-17)

World Time Mode (page E-20)

Stopwatch Mode (page E-14)

E-6

General Guide

• Press C to change from mode to mode.

• To return to the Timekeeping Mode from any other mode, hold down

C for about

three seconds.

• In any mode (except a setting mode), press B to illuminate the display.

Timekeeping Mode

E-5

Hand Home Position Correction ……………………………………………………E-33

To adjust home positions ………………………………………………………E-33

Reference ………………………………………………………………………………E-35

To turn the button operation tone on and off …………………………………E-36

Specifications …………………………………………………………………………E-40

E-4

World Time ………………………………………………………………………………E-20

To view the current time in another time zone ………………………………E-21

To toggle a city code time between Standard Time and

Daylight Saving Time ………………………………………………………E-22

To swap your Home City and World Time City ………………………………E-23

Alarms ……………………………………………………………………………………E-24

To set an alarm time ……………………………………………………………E-25

To test the alarm ………………………………………………………………E-26

To turn an alarm on and off ……………………………………………………E-27

To turn the Hourly Time Signal on and off ……………………………………E-28

Illumination ……………………………………………………………………………E-29

To illuminate the display manually ……………………………………………E-29

To specify the illumination duration……………………………………………E-30

To turn the auto light switch on and off ………………………………………E-32

E-3

Contents

Getting Acquainted …………………………………………………………………… E-1

General Guide ………………………………………………………………………… E-6

Timekeeping …………………………………………………………………………… E-8

To set the time and date ……………………………………………………… E-9

To change the Daylight Saving Time (summer time) setting ………………E-12

Stopwatch ………………………………………………………………………………E-14

Countdown Timer………………………………………………………………………E-17

To use the countdown timer ……………………………………………………E-18

To configure countdown start time settings …………………………………E-19

E-2

• Button operations are indicated using the letters shown in the illustration.

• Each section of this manual provides you with the information you need to perform

operations in each mode. Further details and technical information can be found in

the “Reference” section.

E-1

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

• Be sure to keep all user documentation handy for future reference.

About This Manual

• Depending on the model of your watch, display text appears either as dark figures

on a light background or light figures on a dark background. All sample displays in

this manual are shown using dark figures on a light background.

Operation Guide 5553

E-19

To configure countdown start time settings

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A for about two

seconds until the hour setting of the countdown start

time starts to flash. This is the setting mode.

• Holding down A will initially cause “Hold” to appear

on the screen. Keep A depressed until “Hold”

disappears.

• If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” (page

E-18) to display it.

2. Press C to move the flashing in the sequence shown

below, and select the setting you want to change.

Start Time

(Hours)

Start Time

(Minutes)

3. Press A to exit the setting mode.

Start time

(Hours : Minutes)

E-18

To use the countdown timer

Press D while in the Countdown Timer Mode to start the countdown timer.

• When the end of the countdown is reached, the alarm will sound for 10 seconds or

until you stop it by pressing any button.

• The countdown time is reset to its starting value automatically after the alarm stops.

• Press D while a countdown operation is in progress to pause it.

Press D again to resume the countdown.

• To stop a countdown timer operation completely, first pause it (by pressing D),

and then press A. This returns the countdown time to its starting value. Note that

the countdown start time cannot be changed while a countdown timer operation is

ongoing or paused. To change the start time, you first need to stop the countdown

timer operation completely as described above.

E-17

Countdown Timer

You can set the countdown timer start time within a range

of one minute to 24 hours. An alarm sounds when the

countdown reaches zero.

• All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

C (page E-7).

Start time

(Hours : Minutes)

Seconds

E-16

Stopwatch hand

Elapsed time seconds

Measured time or split time

Hours

• Alternates with “SPL” during

split time display.

Minutes, seconds,

1/100 seconds

• Pressing

D without resetting the displayed time will restart elapsed time

measurement from where it was last stopped (cumulative elapsed time

measurement).

• An ongoing elapsed time measurement operation continues even if you exit the

Stopwatch Mode. In this case, the stopwatch hand indicates the current minutes

count.

E-15

Elapsed Time Measurement

In the Stopwatch Mode, press D to start and stop elapsed time measurement.

• Pressing A while elapsed time measurement is in progress will display the current

split time.

Start Split Stop

Split

cancel

Display

time reset

D A DA A

(Measured time

displayed.)

(Measured time

displayed.)

(Split time

displayed.)

(Stopped) (Stopped)(Measurement)

E-14

Stopwatch

You can use the stopwatch to measure elapsed time and

split times.

• The digital display range of the stopwatch is 999 hours,

59 minutes, 59.99 seconds. The stopwatch continues to

run until you stop it. If it reaches the above limit, it will

restart the time measurement from zero.

• The stopwatch operation continues even if you exit the

Stopwatch Mode.

• All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing

C (page

E-7).

E-13

3. Use D to toggle the DST setting on and off.

DST off ( ) DST on ( )

• The default DST setting is OFF ( ).

4. When the setting you want is selected, press

A to exit the setting mode.

• The DST indicator appears to indicate that Daylight Saving Time is turned on.

12-hour and 24-hour timekeeping

• With the 12-hour format, the PM indicator (P) appears on the lower display for times

in the range of noon to 11:59 p.m. and no indicator appears for times in the range

of midnight to 11:59 a.m.

• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

the PM indicator (P).

• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

E-12

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down A for about two

seconds until “SET” appears on the display.

• Note that keeping A depressed too long (for about

five seconds) will cause a different type of setting

mode to be entered (page E-33).

2. Press C. This will display the DST setting screen.

DST indicator

E-11

Screen: To do this: Do this:

Reset the seconds to Press

Change the hour and minutes

Use D (+) and B (–).

Change the year, month, or day

Toggle the button operation tone

between (on) and (off) Press D.

Toggle the display illumination duration

between 1.5 seconds ( ) and three

seconds ( ) Press D.

5. Press

A to exit the setting mode.

• The day of the week is displayed automatically in accordance with the date (year,

month, and day) settings.

E-10

3. Press C to change the flashing screen content in the sequence shown below to

select the other settings.

City

Code DST 12/24-Hour

Format Seconds Hour Minutes

YearMonthDay

Button

Operation Tone

Illumination

Duration

C C C C C

C C

CCCC

4. When the timekeeping setting you want to change is flashing, use

D or B to

change it as described below.

Screen: To do this: Do this:

Change the city code Use

D (east) and B (west).

Toggle the DST setting between

Daylight Saving Time ( ) and

Standard Time ( ).

Press D.

Toggle between 12-hour ( ) and

24-hour ( ) timekeeping Press D.

Operation Guide 5553

E-29

Illumination

An LED (light-emitting diode) illuminates the face of the

watch for easy reading in the dark. The watch’s auto light

switch turns on illumination automatically when you angle

the watch towards your face.

• The auto light switch must be turned on (indicated by

the auto light switch indicator) for it to operate.

• See “Illumination Precautions” (page E-38) for other

important information about using illumination.

To illuminate the display manually

In any mode, press B to turn on illumination.

• The above operation turns on illumination regardless of

the current auto light switch setting.

• You can use the procedure below to select either 1.5

seconds or 3 seconds as the illumination duration.

When you press B, the illumination will remain on for

about 1.5 seconds or 3 seconds, depending on the

current illumination duration setting.

Auto light switch

indicator

E-28

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use D to select the Hourly Time

Signal ( ) (page E-25).

2. Press A to toggle it on and off.

• The Hourly Time Signal on indicator is shown on the

display in all modes while this function is turned on.

Hourly time signal

on indicator

E-27

To turn an alarm on and off

1. In the Alarm Mode, use D to select an alarm.

2. Press A to toggle it on and off.

• Turning on a alarm ( , , , or )

displays the alarm on indicator on its Alarm Mode

screen.

• In all modes, the alarm on indicator is shown for any

alarm that currently is turned on.

• The alarm on indicator flashes while the alarm is

sounding.

• The snooze alarm indicator flashes while the snooze

alarm is sounding and during the 5-minute intervals

between alarms.

Snooze alarm indicator

Alarm on indicator

E-26

3. Press C to move the flashing between the hour and minute settings.

4. While a setting is flashing, use

D (+) and B (–) to change it.

5. Press A to exit the setting mode.

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the

watch is in. In the case of the snooze alarm, the alarm operation is performed a total

of seven times, every five minutes, or until you turn the alarm off (page E-27).

• Alarm and Hourly Time Signal operations are performed in accordance with the

current time in your Home City, as kept in the Timekeeping Mode.

• To stop the alarm tone after it starts to sound, press any button.

• Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen (page E-9)

Displaying the setting screen (page E-25)

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

E-25

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

D D D D

• To set an alarm time, display the applicable alarm

screen ( through , or ).

• is the hourly time signal setting (page E-28).

• The snooze alarm operation repeats every five

minutes.

2. After you select an alarm, hold down A for about two seconds until the hour setting

of the alarm time starts to flash. This is the setting mode.

• Holding down A will initially cause “Hold” to appear on the screen. Keep

depressed until “Hold” disappears.

• This operation turns on the alarm automatically.

OFF

E-24

Alarms

When an alarm is turned on, the alarm tone will sound

when its alarm time is reached. One of the alarms is a

snooze alarm, while the other four are daily alarms.

You also can turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour.

• The snooze alarm screen is indicated by , while the

other alarm screens are numbered through .

The Hourly Time Signal screen is indicated by .

• All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C (page E-7).

Alarm time

(Hour : Minutes)

E-23

Swapping your Home City and World Time City

You can use the procedure below to swap your Home City and World Time City. This

changes your Home City to your World Time City, and your World Time City to your

Home City. This capability can come in handy when you frequently travel between two

cities in different time zones.

To swap your Home City and World Time City

1. In the World Time Mode, use D to select the World Time City you want.

2. Press A and B at the same time until the watch beeps.

• This will make the World Time City you selected in step 1 your Home City, and

cause the hour and minute hands to move to the current time in that city. At the

same time, it will change the Home City you had selected prior to step 2 your World

Time City, and cause the content of lower display to change accordingly.

• After swapping the Home City and World Time City, the watch stays in the World

Time Mode with the city that was selected as the Home City prior to step 2 now

displayed as the World Time City.

E-22

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, press D to display the city

code (time zone) whose Standard Time/Daylight Saving

Time setting you want to change.

2. Hold down A for about two seconds to toggle between

Daylight Saving Time ( indicator displayed) and DST

Standard Time ( indicator not displayed).DST

• Holding down A will initially cause “Hold” to appear on

the screen. Keep

A depressed until “Hold” disappears.

• The DST indicator is shown in the lower display while

Daylight Saving Time is turned on.

• You can turn on DST individually for each city code,

except UTC.

• Turning on DST for the city code that is currently

selected as your Home City will turn on DST for normal

timekeeping.

DST indicator

E-21

To view the current time in another time zone

In the World Time Mode, use D to scroll through available city codes (time zones).

Holding down the button scrolls at high speed.

• The lower display shows the current time in the World Time City.

• To select the UTC time zone (Differential 0), press B and D at the same time.

• When the city code (time zone) you want is selected, you can press A to display

the date. After about one second, the watch will resume regular timekeeping for the

currently selected city.

Hour : Minutes Date

Seconds

One second

E-20

World Time

World Time digitally displays the current time in one of

48 cities (31 time zones) around the world. A simple

operation swaps your Home City with the currently

selected World Time City.

• The times kept in the World Time Mode are

synchronized with the time being kept in the

Timekeeping Mode. If you feel that there is an error in

any World Time Mode time, check to make sure you

have the correct city selected as your Home City. Also

check to make sure that the current time as shown in

the Timekeeping Mode is correct.

• Times in the World Time Mode are based on UTC

offsets. See the “City Code Table” at the back of this

manual for information about the UTC offsets that are

supported.

• All of the operations in this section are performed in the

World Time Mode, which you enter by pressing

(page E-7).

Currently selected

World Time City

World Time

Product specificaties

Merk:	Casio
Categorie:	Horloge
Model:	G-Shock G-Steel GST-410-1AER
Gewicht:	108 g
Breedte:	59.1 mm
Diepte:	52.4 mm
Hoogte:	16.1 mm
LED backlight:	Ja
Type horloge:	Horloge
Mechanismetype:	Quartz
Chronograaf:	Ja
Chronometer:	Nee
Type wijzerplaat horloge:	Analoge & lcd-wijzerplaat
Waterdicht:	Ja
Stopwatch:	Ja
Countdown timer:	Ja
Waterbestendig druk:	20 ATM
Waterbestendig diepte:	200 m
Schokbestendig:	Ja
Wereldklok functie:	Ja
Alarm functie:	Ja
Agenda:	Ja
Klokmodus:	12/24 uur
Aantal keren alarm:	5
Nauwkeurigheid:	15 sec/maand
Aanpasbare afteltimer:	1 - 1440 min
Afteltimer maateenheden:	Hour,Minute,Second
Nauwkeurigheid stopwatch:	0.01 s
Meetcapaciteit stopwatch:	1000 hours
Type kalender:	Overdag
Horlogekast materiaal:	Resin,Stainless steel
Kleur behuizing:	Black,Stainless steel
Band materiaal:	Kunststof
Hoofdkleur van band:	Zwart
Glas type van horloge:	Mineraalglas
Hoesvorm:	Rond
Krasbestendig glas:	Ja
Hoofdkleur van wijzerplaat:	Zwart
Vormgeving:	Sport
Geslacht:	Man
Levensduur batterij/accu:	3 jaar
Tijdszones:	Ja
Tijdzones aantal:	31
Productontwerp:	Sport