Cardo Q-Solo Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Cardo Q-Solo (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 285 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Q-solo
Manual
scala
rider® Q-solo
1 INTRODUCTION
2 CHARGING THE SCALA RIDER
3 GETTING STARTED: 3.1 STATUS LIGHTS, 3.2 GENERAL FUNCTIONS, VOX ACTIVATION3.3
4 PAIRING AND USING A MOBILE PHONE, GPS DEVICE OR ANY MUSIC PLAYERS:
4.1 PAIRING
BLUETOOTH
, 4.2 MAKING AND RECEIVING PHONE CALLS, LISTENING TO MUSIC VIA4.3 A2DP
5 TROUBLESHOOTING
6 SUPPORT
INDEX
I M P O R T A N T :
This is version 1.0 o f the User
Manual. Please note, that our
manual is periodically updated
on the Cardo website to include
the ver y latest featu res and
functions of your new scala rider.
➋ ➌
1. Power Button
2. LED Indicator
3. Music / Mobile Button
4. Volume Up
5. Charging
6. Volume Down
INTRODUCTION
Thank you for choosing the scala rider Q-solo Bluetoot headset
for motorcycle helmets. This manual will help you set up, congure
and operate it.
1
CHARGING THE SCALA RIDER
Make sure that your scala rider is fully charged for at least 4 hours
before initial use.
Charging with a 5v wall charger is faster than charging with a
computer USB port.
LED ON – Charging RED
LED OFF – Charging completeRED
The scala rider Q-solo is waterproof and dustproof. However,
when in use, the USB silicone cover should be kept tightly closed
to prevent moisture from entering the unit.
2
GETTING
STARTED
3.1 STATUS LIGHTS
None scala rider is OFF
The BLUE LED ashes once every 3 seconds Standby mode. No active audio sources
The BLUE LED ashes twice every 3 seconds Active mode – Call in progress / music or other audio source is ON
The RED LED ashes once every 3 seconds Standby mode – Battery is low
The RED LED ashes twice every 3 seconds Active mode – Battery is low
Solid RED Charging
3
scala
rider® Q-solo
3.2 GENERAL FUNCTIONS
Power ON / OFF Press for 2 seconds
ON: 3 BLUE ashes + Ascending tone OFF: 3 RED ashes + Descending tone
Volume Tap or to adjust and set volume of current audio source
Mute Tap and simultaneously
Battery Check In Standby, press for 2 seconds:
LED = Full charge • LED = Half charge • LED = Almost emptyBLUE PURPLE RED
3.3 VOX ACTIVATION
Your scala rider oers a voice operated feature for hands-free
operation.
Answer a call Speak any word loudly into the microphone
Reject a call Remain silent for about 15 seconds
4.1 PAIRING BLUETOOTH
1. Make sure is enabled on your phone/GPS/MP3 player.Bluetooth
2. Check the scala rider is in Standby mode (single LED ashes every 3 seconds).
3. Press for at least 5 seconds until the LED ashes once every 3 secondsBLUE
4. Search for devices on your phone/GPS/MP3 player by following the device’s Bluetooth
instructions.
5. After a few seconds the device will list “scala rider Q-solo . Select it.
6. If prompted for a PIN or Passkey, enter 0000 (four zeros).
7. The device will conrm that pairing has succeeded and will ash for 2 secondsPURPLE
8. If pairing is not completed within 2 minutes, the scala rider will return to Standby mode.
PAIRING AND USING A MOBILE PHONE, GPS DEVICE OR ANY MUSIC PLAYER
To connect your scala rider to a device you must rst pair them. Once paired, they will Bluetooth
automatically recognize each other whenever they are within range (10m / 33ft).
Your scala rider has channel for connecting to a mobile phone, GPS device Bluetooth
and a music player with A2DP.
NOTES:
Not all Bluetooth mobile phones can broadcast
Bluetooth Stereo music (A2DP), even if the phone
has a music player function. Consult your mobile
phone’s User Manual for more information.
Not all GPS devices allow connection to Bluetooth
Bluetooth audio devices. Consult your GPS User
Manual for more information.
After pairing, you may need to tap to connect
the scala rider .
4.2 MAKING AND RECEIVING PHONE CALLS
Answer a call Tap or say any word loudly to answer by VOX
Reject a call Remain silent for 15 seconds, or press and hold for
2 seconds
End a call Tap
Voice Dial*
(if supported by
mobile phone)
Tap and simultaneously and follow the prompt
from the mobile
Redial* Press and for 2 seconds
*This feature is not available during mobile calls
4.3 LISTENING TO MUSIC VIA A2DP
Available only on compatible Bluetooth audio sources
Play In Standby, tap
Pause/Stop Press for 2 seconds
Next Track With music ON, tap
Previous Track* With music ON, double tap
*With some phones you may need to repeat this action
TROUBLESHOOTING
Reboot If your scala rider stops responding, reset it by turning it oand then on again (press for 2 seconds).
Reset Pairing
(Deletes paired device)
1. In Standby, press for 5 secs until LED ashes / .RED BLUE
2. Press for 2 seconds until LED ashes 5 times in .PURPLE
Unresponsive Device Please connect to your charging cable for 30 seconds to allow the device to reset.
4
5
6
USA and Canada: 1-800-488-0363
International: +49 89 450 36819
CONTACT & SUPPORT
1
MAN00001 QG onlinesolo EN 001
support@cardosystems.com
cardosystems.com
www


Product specificaties

Merk: Cardo
Categorie: Niet gecategoriseerd
Model: Q-Solo

Heb je hulp nodig?

Als je hulp nodig hebt met Cardo Q-Solo stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Cardo

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd