Caliber MCD230M Handleiding

Caliber Autoradio MCD230M

Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor Caliber MCD230M (16 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
E N G L I S H
2
S P E C I F I C A T I O N S
GENERAL
Power requirement DC 12V
Current consumption 15A
Power output 4 X 55W
FM SECTION
Frequency range 87.5 to 108 MHz
Usable sensitivity 3uV
I.F frequency 10.7MHz
LINE-OUT
Output 1 Volt
CD PLAYER
System Compact Disc Audio System
Usable disc Compact Disc
Signal format Sampling frequency 44.1KHz
No. of quantization BITs 1 BIT
Frequency characteristics 5-40Hz-5dB 10K-20KHz-5dB
Signal to noise radio 70dB (1KHz) (IEC-A NET WORK)
Number of channels 2 STEREO
Chassis dimensions (mm) 184 (W) X 54 (H) X 170 (D)
N
O
E
FLIP DOWN DETACHABLE CD/RW MP3 PLAYER
-
MOD
+
OPEN
SEL
7
PTY
MP3
APS
M1/PAU M2/SCN M3/RPT M4/SHF M5 M6
CLK
DIGITAL AUDIO
COMPACT
TA
0
IR
AF
8
9
T-DN
T-UP
PWR
ENTER
BND
20
1. OPEN button
2. SEL (Volume/Bass/Treble/Balance/Fader)
3. TRACK UP/DOWN buttons
4. APS/MP3 button
5. TA button
6. MODE button
7 -8-9-10-11-12. PRESET MEMORY buttons
13. PTY button (Program Type)
14. CLOCK button
15. AF button (Alternative Frequencies)
16. BAND button
17. POWER button
18. Flashing LED
19. RESET button
๎€€
RCA output
Speaker output
MCD 230M manual 02-12-2005 08:30 Pagina 1
E N G L I S H
3
O P E R A T I O N
For CD/RW + RDS + MP3 model with optional subwoofer function
1. OPEN button
Press it to flip down the front panel.Then you can insert the CD disc into the CD
compartment or press the Eject button to eject the disc.
2. SEL ( AUDIO MODE SELECT)/ +/- buttons
Press SEL button to change the mode in the sequence of:
A. The volume level can be adjusted at any time by pressing the audio level + or -
button as select mode has been initially defaulted at volume mode.
B. The volume level is also obtained by stepping through the SEL button until the
function VOL is displayed and then press + or - button to adjust the sound level.
C. Press SEL button to select the BAS,TRE, BAL, FAD mode, then press +/- button
to adjust the level.
D. Press SEL button, hold for more than 2 seconds and select + or - button, so a
beep sound can be heard.
3. TRACK UP /DOWN buttons
A. During CD mode, pressing the >> button will allow you to track forwards. Hold
it to skip forwards.
B. During MP3 mode, pressing the >> button will allow you to track forwards.Hold
it to skip forwards.For MP3 playing,these two buttons act as the digit 8 & 9 key.
C.
During RADIO mode, press and hold >> or << for more than 2 seconds to
manually search a channel.Then press >> or << to automatically search a channel.
4. APS/MP3 button
In radio mode:
When pressed short, the radio searches for each preset station.
When the field strength level is more than the threshold level of stop level,the radio
will hold at that preset number for a few seconds with releasing mute, and then
searches again. In FM band, FM 1, FM 2 and FM 3 are checked one at a time.When
pressed long (more than 1 second),the radio searches from the current frequency
and checks the signal strength level until 1 cycle search is finished. And then the 6
strongest stations are preset to the corresponding preset number.The AS operation
is implemented in each selected band.When the AS operation is finished, the radio
executes the preset scan.
In MP3 mode:
Press 0-9 and ENTER button to play the track, number 1-108.
5. TA button
TA function (traffic announcement)
When pressed short, it is activated as TA mode on or off.
When TA mode is on and traffic announcement is transmitted:
1. When the unit is in CD mode, it will switch to radio mode temporarily.
2. Temporary switch over to an EON (Enhanced Other Networks) linked station
when EON detects a traffic announcement on that other program.
3. If the volume level was under the threshold point, it will be raised to the
threshold point. But if the user changed the volume level which was more than
the threshold point (min.TA volume level),it will be set to the last level.
When pressed long, EON TA LOCAL / EON TA DISTANCE mode is selected:
The purpose of this key is to reduce unwanted EON TA switching, when EON TA
information was received from current station and the radio switched to that EON
linked station, but no information could be received because the EON linked
station is located too far from that area.
So the radio is switched back to the current station.
In above operation,the user may listen to a wrong program or mute sound for a while.
EON TA LOCAL mode
When the field strength level of EON linked is less than the threshold level, the radio
does not switch to that station, and the user can hardly hear any disturbances.
When EON TA LOCAL mode is selected, EON TA LO on the numeric display is
indicated for a few seconds.
EON TA DISTANCE mode
EON TA switching is trying to implement the information of the current station.
When EON TA DISTANCE mode is selected, EON TA DX on the numeric display
is indicated for a few seconds.
6. MODE button
Press it repeatedly to select CDP, AUX and RADIO mode in sequence and circulation.
For SUBWOOFER function (optional), press and hold for more than 2 seconds to
select SUBWOOFER mode.
For MP3 playing, this button can act as the digit 7 key.
7-8-9-10-11-12. PRESET MEMORY buttons
A. To memorize the current frequency, press any one of the six preset buttons and
hold for more than 2 seconds.
B. To r ecall the preset memory, press one of the preset buttons (1-6).
VOL BAS TRE BAL FAD
(Volume) (Bass) (Treble) (Balance) (Fader)
TA seek Pi sound
Retune L Mask DPI
Beep
MCD 230M manual 2 02-12-2005 08:24 Pagina 2


Product specificaties

Merk: Caliber
Categorie: Autoradio
Model: MCD230M

Heb je hulp nodig?

Als je hulp nodig hebt met Caliber MCD230M stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Autoradio Caliber

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio