Caliber CA 2260 Handleiding

Caliber Autoradio CA 2260

Lees hieronder de 📖 handleiding in het Nederlandse voor Caliber CA 2260 (12 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 71 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

CA 2360 Rally

Ma x i m um Pow er Out put a t 1 4 ,4V

4Ω20Hz - 30kHz THD 1% 2x 120W

2Ω20Hz - 30kHz THD 1% 2x 180W

4Ω1kHz Mono Bridged 1x 360W

Co n t in u o us Power Out put a t 1 4 ,4V

4Ω20Hz - 30kHz THD 1% 2x 40W

2Ω20Hz - 30kHz THD 1% 2x 60W

4Ω1kHz Mono Bridged 1x 120W

Fus e Ra t ing 20A

D i m en s io ns 210x260x65mm

CA 2500 Rally

Ma x i m um Power Ou t put a t 1 4 , 4 V

4Ω20Hz - 30kHz THD 1% 2x 225W

2Ω20Hz - 30kHz THD 1% 2x 250W

4Ω1kHz Mono Bridged 1x 500W

Co n t in u o us Power Out put a t 1 4 ,4V

4Ω20Hz - 30kHz THD 1% 2x 75W

2Ω20Hz - 30kHz THD 1% 2x 95W

4Ω1kHz Mono Bridged 1x 190W

Fus e Ra t ing 25A

D i m en s io ns 240x260x65mm

Alle Caliber Rally 2-kanaals versterkers hebben de

volgende technische gegevens. Technische gegevens die

per model verschillen zijn apart opgenomen.

Frequentierespons (+0, -1dB)20Hz-30kHz

Totale harmonische vervorming <0,05%

Signaal-ruisverhouding (A-Weighted) >103dB

Ingangsgevoeligheid RCA-ingang 3V - 200mV

Ingangsgevoeligheid High-Level ingang 10V - 2V

Laagdoorlaatfilter 80Hz

Variabele bassversterking 0dB- +6dB

Uitgangsimpedantie 2 - 8Ω

N E D E R L A N D S

All Caliber Rally 2-channel Amplifiers have the following

specifications.

Variable specifications are listed per model.

Frequency response (+0, -1dB)20Hz -30kHz

Total Harmonic Distortion <0,05%

Signal to noise ratio (A-Weighted) >103dB

Input Sensitivity RCA input 3V - 200mV

Input Sensitivity High Level input 10V - 2V

Low Pass Filter 80Hz

Variable Bass Boost 0dB - +6dB

Output Impedance 2 - 8Ω

NORMAL SYSTEM SET-UP

OPTIONAL SYSTEM SET-UP

Folgende technische Daten sind allen 2-Kanal-Verstärkern

vom Caliber Rally gemeinsam. Abweichende Wer te sind

unter den einzelnen Modellen aufgeführt.

Frequenzgang (+0, -1dB)20Hz-30kHz

Gesamtklirrfaktor <0,05%

Rauschabstand (A-bewertet) >103dB

Eingangsempfindlichkeit Cinch-Eingang 3V - 200mV

Eingangsempfindlichkeit Hochpegel-Eingang 10V - 2V

Tiefpassfilter 80Hz

Variable Basshervorhebung 0dB- +6dB

Ausgangsimpedanz 2 - 8Ω

Alle Caliber Rally 2-kanals forsterkere har følgende spe-

sifikasjoner.

Variable spesifikasjoner listes opp for hver modell enkeltvis.

Frekvensrespons (+0, -1dB)20Hz-30kHz

Total harmonisk forvrengning <0,05%

Forhold mellom signal og støy (A-vektet) >103dB

Inngangsfølsomhet RCA-inngang 3V - 200mV

Inngangsfølsomhet høynivåinngang 10V - 2V

Lavpassfilter 80Hz

Variabel basshevning/senking 0dB- +6dB

Utgangsimpedans 2 - 8Ω

Todos los amplificadores Caliber Rally 2-canales tienen las

siguientes características.

Para cada modelo se indican las características variables.

Respuesta de frecuencia (+0, -1dB)20Hz-30kHz

Distorsión armónica total <0,05%

Media señal-ruido (ponderada en A) >103dB

Entrada Input Sensitivity RCA 3V - 200mV

Entrada Input Sensitivity High level 10V - 2V

Filtro de paso bajo 80Hz

Compensador de Bajos Variable 0dB- +6dB

Impedancia de salida 2 - 8Ω

Tous les amplificateurs Caliber Rally à 2 canaux possèdent

les caractéristiques ci-dessous. Les caractéristiques

variables sont définies pour chaque modèle.

Réponse en fréquence (+0, -1dB)20Hz-30kHz

Distorsion harmonique totale <0,05%

Rapport signal/bruit (pondéré A) >103dB

Sensibilité d'entrée Entrée Cinch 3V - 200mV

Sensibilité d'entrée haut niveau 10V - 2V

Filtre passe-bas 80Hz

Accentuation variable des graves 0dB- +6dB

Impédance de sortie 2 - 8Ω

Tutti gli amplificatori Rally a 2 canali della Caliber hanno le

seguenti specifiche tecniche.

Le specifiche tecniche variabili sono elencate per modello.

Risposta in frequenza (+0, -1dB)20Hz-30kHz

Distorsione armonica totale <0,05%

Rapporto segnale/rumore (pesato 'A') >103dB

Sensibilità di ingresso RCA 3V - 200mV

Sensibilità di ingresso High-level 10V - 2V

Filtro Low-Pass 80Hz

Enfatizzazione bassi variabile 0dB- +6dB

Impedenza di uscita 2 - 8Ω

Todos os amplificadores Caliber Rally 2-canais têm as

seguintes características.

Para cada modelo indicam-se as características variáveis.

Resposta de frequência (+0, -1dB)20Hz-30kHz

Distorção harmónica total <0,05%

Média sinal-ruído (ponderada em A) >103dB

Entrada Input Sensitivity RCA 3V - 200mV

Entrada Input Sensitivity High Level 10V - 2V

Filtro de passagem baixa 80Hz

Compensador de Baixos Variável 0dB- +6dB

Impedância de saída 2 - 8Ω

E N G L I S H

E S P A Ñ O L P O R T U G U Ê S

S V E N S K

D E U T S C H I T A L I A N O

F R A N C A I S

E N G L I S H

H I G H L E V E L I N P U T

• Connect the loudspeaker outputs of your radio to the wires which are already on the special plug

you found in the box.

Ta ke good care of the polarity (+ or -), and which signal is right or left.

L- = White, L + = White/Black R- = Gray, R + = Gray/Black GND = Black, connect to Ground.

R C A I N P U T

• Connect the RCA-outputs of your radio to the RCA input terminals of the amplifier.Take good care

that you connect the Right output of your radio to a Right input of your amplifier, and that you con-

nect the Left output of your radio to a Left input of your amplifier.

S P E A K E R O U T P U T

• All the Caliber Rally amplifiers have Stereo/Bridgeable Tri-Mode speaker output terminals. The

amplifier has its own stereo/bridge switch built-in, so there is no need to select a stereo or bridged

mode.You can connect the speakers to each channel in stereo mode, and simultaneously connect

a sub-woofer to the speaker terminal in a bridged mode.

• Pay attention in connecting your speakers and/or sub-woofers. Be sure to obser ve correct speaker

output connections for front, rear and their polarity.

• In the stereo mode, connect the right speaker output to the right speaker and the left to the left.

Connect the positive (+) output to the positive (+) speaker terminal and the negative (-) output

to the negative (-) speakerterminal.

• In the bridged mode connect the left (+) positive to the positive speaker terminal and the right (-)

negative to the negative speaker terminal.

• Do not use the negative speaker output commonly for left and right speakers (common ground).

Improper polarity causes a loss of bass response.

• Never connect the negative speaker output to the chassis of your vehicle. This can cause severe

damage to your Car Audio System.

A M P L I F I E R A D J U S T M E N T S

Before you start adjusting your amplifier, you must make up your mind how you want to use it, for

full range music, or as a subwoofer amplifier. If you want to use it as a subwoofer amplifier, you must

put the crossover switch in the LowPassFilter (LPF) position. Now the amplifier will only have an

output of signals up to 100Hz. If you want the amplifier to play in full range, the crossover-switch

must be in the Full-position, and the output will be the whole frequency range from 20Hz to 30kHz.

• Put the input level adjustment knob to the minimum.

• Put the volume of your radio to 3/4 of the maximum.

• Adjust the Bass Boost to your personal sound. (The Bass Boost allows you to give a 6 dB boost to

the signal. Every 3dB boost doubles the power required for the amplifier, so a 6dB boost will need

4 times the power!)

• Now adjust the input level of the front channel. Slowly turn up the input level and listen carefully

untill you hear the amplifier begin to distort. A Caliber Amplifier “clips” very softly, so this can some-

times be a difficult adjustment. If you have turned up the Bass Boost to much, the amplifier will start

clipping immediatly. In that case you must turn back the Bass Boost and start adjusting the inputle-

vel again.You will hear that the Bass you wanted can be required in this way.

C A L I B E R W A R R A N T Y

Due to the complexity of our products, we strongly recommend that this amplifier is installed by

your authorized Caliber dealer. If properly installed by your dealer we provide a warranty for 12

month from the date of purchase.

If you install this amplifier yourself, we wish you lots of fun and succes in doing so. If you follow our

guidelines, you’ll get the best result. Our warranty, however, will be limited to and not exceed 30

days from the date of purchase.

F E A T U R E S

• Bridgeable outputs.

• ’Tri-mode’ output capability, simultaneous stereo & bridged mono set up is possible.

• Pulse Width Modulated (PWM) MOSFET Power Supply.

• Variable input sensitivity: RCA input 0.2V to 3V.

• Variable input sensitivity: High Level input 2V to 10V.

• Thermal-, Overload- and Shor tcircuit protection.

• Excellent muting circuitry assures no turn on/off ‘pops’.

• Built-in Full Range/Low Pass Switch.

• Chromium plated power connectors for optimal power distribution.

• European design and engineering.

• Chromium plated speaker connectors for optimal signal output.

M O U N T I N G

The amplifier has to have at least 5 cm (2”) ventilation space at all sides, to allow the heat to rise

away from the amplifier. Be sure that the power and signal cables can enter and leave the amplifier

in a straight line, to avoid the risk of malfunction. Always place the power- and signalcables at

opposite sides of the vehicle to reduce any noises.

The amplifier should be protected from exposure to moisture and direct sunlight.

Mark the mounting surface using the amplifier as a template, then drill 2.5 mm (1/8”) diameter holes

at the marked locations and mount the amplifier using the supplied self-tapping screws.

I N S T A L L A T I O N

Remember to always disconnect battery ground before working on a vehicle’s electrical system!

Always place a fuse or circuit breaker no more than 30 cm (12”) from the batter y, no greater than

the fuse(s) of your amplifier for optimal protection.

G E T T I N G Y O U R P O W E R S T A R T E D

• First, the +12V terminal is connected directly to the battery of your car. Use a cable of at least 10

mm2(8 AWG), and make sure that the connectors are of the same value.

- Don’t forget the extra “Vehicle protection” fuse.

- The 12V + terminal should NOT be connected to the car fuse box.

• Second, the ground terminal (GND) must be fastened securely to the chassis of the vehicle with the

same gauge cable as the positive cable (the same amount of power has to run through it). Ensure

that all paint, undercoating or any other insulation is removed from the area where you want to

make your ground connection to.

• Third, the last cable to connect is your remote turn-on (REM). Many radio-cassette and CD-players

have an output terminal for connection of the REM of an amplifier. If you don’t have such an out-

put, a separate switch must be installed to control your amplifiers on/off function.

S I G N A L I N P U T

The Caliber Rally Amplifiers offer you two possibilities for your signal input.

• A High Level input, using the loudspeaker output from your radio and the special High Level input-

plug you found in the box.

• Signal input by using a RCA cable from your radio’s RCA outputs to the amplifiers signal input RCA’s.

NEVER USE HIGH LEVEL INPUT AND RCA INPUT AT

THE SAME TIME!

Product specificaties

Merk:	Caliber
Categorie:	Autoradio
Model:	CA 2260

Heb je hulp nodig?

Als je hulp nodig hebt met Caliber CA 2260 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Autoradio Caliber

Caliber RCD 239DAB-BT Handleiding

4 Augustus 2023

Caliber RMD 806BT Handleiding

19 Juni 2023

Caliber RCD120DAB-BT Handleiding

18 Juni 2023

Caliber RMD056DAB-BT Handleiding

13 Juni 2023

Caliber CA 75 2 Handleiding

7 Juni 2023

Caliber CA 2260 Handleiding

10 Mei 2023

Caliber RMD402DAB-BT Handleiding

5 Mei 2023

Caliber RMD055 Handleiding

3 Mei 2023

Caliber MCD263BT Handleiding

30 April 2023

Caliber RMD213DAB-BT Handleiding

29 April 2023

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio

Kenwood KDC-X5200BTM Handleiding

3 December 2024

Kenwood KDC-130UG Handleiding

3 December 2024

Boss BCPA12 Handleiding

30 November 2024

Alpine mrp m 200 Handleiding

16 November 2024

Panasonic CQ-5250T Handleiding

23 November 2024

Deaf Bonce Machete MFA-1.1500 Handleiding

20 November 2024

Xblitz RF100 Handleiding

15 November 2024

Xblitz RF300 Handleiding

15 November 2024

Xblitz RF500 CAM Handleiding

15 November 2024

Xblitz RF350 CAM Handleiding

15 November 2024