Bushnell Bone Collector 1000 Handleiding

Bushnell Afstandsmeter Bone Collector 1000

Lees hieronder de đź“– handleiding in het Nederlandse voor Bushnell Bone Collector 1000 (22 pagina's) in de categorie Afstandsmeter. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/22
LASER RANGEFINDER
Model # LBC1000 07-23
2
Click to Return to the Table of Contents
INTRODUCTION
Your Bushnell® Bone Collector™ 1000 is an ultra-compact, premium laser rangender that uses the latest digital
technology. It provides precise range readings from 5-1000 yards/5-914.4 meters. This rangender features Bushnell’s
patented ARC™ (Angle Range Compensation with Ballistics Intelligence), a ranging engine for faster, more consistent
response and readings, a vivid LCD with higher light transmission, and water resistant (IPX4) construction.
HOW OUR DIGITAL TECHNOLOGY WORKS
The Bone Collector™ 1000 laser rangender emits invisible, eye safe, infrared energy pulses. The Bone Collector™ 1000
rangender’s microprocessor results in instantaneous and accurate readings every time. Sophisticated digital technology
instantaneously calculates distances by measuring the time each pulse travels from the rangeîž“nder to the target and back.
WARNING: AS WITH ANY LASER DEVICE, IT IS NOT RECOMMENDED TO VIEW THE EMISSIONS FOR LONG
PERIODS WITH MAGNIFIED LENSES DIRECTLY.
PARTS GUIDE
POWER/FIRE BUTTON
MONOCULAR
EYEPIECE
BATTERY COMPARTMENT
LASER TRANSMITTER LENS
MONOCULAR/LASER
RECEIVER LENS
STRAP LUG
TABLE OF CONTENTS
HOW OUR DIGITAL TECHNOLOGY WORKS 2
BATTERY ACTIVATION / BATTERY LIFE INDICATOR 3
BASIC OPERATION 3
DISPLAY INDICATORS/ICONS 3
CHOOSING DISTANCE UNITS 3
AUTOMATIC SCAN 4
ANGLE RANGE COMPENSATION (ARC) 4
CLEANING AND GENERAL CARE 4
TROUBLESHOOTING 4
WARRANTY 5
LANGUAGES
FRANÇAIS 6
ESPAĂ‘OL 10
DEUTSCH 14
ITALIANO 18
3
Click to Return to the Table of Contents
BATTERY ACTIVATION / BATTERY LIFE INDICATOR
Before îž“rst use: Remove the battery compartment cover by lifting the battery cover tab and
then rotating the cover counter-clockwise. Remove and discard the plastic disc covering the
positive battery terminal, then replace the battery cover. NOTE: It is recommended that the CR2 3-volt
lithium battery be replaced at least once every 12 months. Please insert it into the compartment’s negative end rst.
• Full charge
• 3/4 battery level remaining
• 1/2 battery level remaining
• 1/4 battery level remaining
Battery icon blinks - the battery needs to be replaced and unit will not be operable.
BASIC OPERATION
1. While looking through the laser rangeîž“nder, press the Power/Fire button once to activate the display.
2. If the display appears blurry, rotate the rubber eyecup/diopter adjustment in either direction until the display is sharp for
your vision.
3. Placing the aiming circle (located in the center of the display) on a target at least 5-6 yards away, press and hold the Fire
button down until the range reading is displayed below the aiming circle.
4. Once a range has been acquired, you can release the Fire button. The four “crosshairs” just outside the aiming circle will go
out, indicating the laser is no longer being transmitted. The display will remain on and display the last distance measurement
for
30 seconds u
ntil the display automatically switches off to extend battery life.
5. You can press the Fire button again at any time to check the range to a new target. To re-îž“re, press the button down again.
6. To scan the laser across an area and get continuously updated range readings, continue to hold the Fire button down and
sweep the rangeîž“nder over multiple targets. The crosshairs outside the aiming circle will îť´ash to indicate scan operation.
WARNING: DO NOT POINT THE LASER TRANSMITTER INTO A PERSON’S EYES.
DISPLAY INDICATORS/ICONS
Bone Collector™ 1000 rangender’s display elements:
1. Battery Level Indicator
2. Aiming Circle/Dot
3. Active/Scan Laser Indicator
4. Primary Numeric Display, Line-of-sight Distance
5. Range (Distance) Units
6. Setup Mode Indicator
7. Angle Indicator
CHOOSING DISTANCE UNITS
The Setup Menu is used to select the distance units: Yards or Meters. While the unit is off, press and hold the Power/Fire
button to enter the Setup Menu (6). The rst setting is Yards, and “Y” will ash, indicating that the distance unit is selected.
Continue to hold the Power/Fire button for three seconds to change to Meters until “M” appears. Continue to hold the
Power/Fire button for three seconds to change to Feet until “FEEt” appears.
Release the Power/Fire button to conîž“rm the distance unit option.
1
2
3
4
5
6
7


Product specificaties

Merk: Bushnell
Categorie: Afstandsmeter
Model: Bone Collector 1000

Heb je hulp nodig?

Als je hulp nodig hebt met Bushnell Bone Collector 1000 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Afstandsmeter Bushnell

Handleiding Afstandsmeter

Nieuwste handleidingen voor Afstandsmeter