BSS Audio Soundweb London MC-1 Handleiding

BSS Audio Niet gecategoriseerd Soundweb London MC-1

Lees hieronder de 📖 handleiding in het Nederlandse voor BSS Audio Soundweb London MC-1 (9 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/9
User’s Guide
BSS Audio MC-1
Stand-Alone Media Converter
•Gigabit Ethernet
•Copper to Fiber
•1000Base-T to 1000Base-SX/LX
BSS MC-1 Gigabit Ethernet mediaAudio
converter connects 1000Base-T
shielded or unshielded twisted-pair copper
cable to 1000Base-SX or 1000Base-LX, fiber-
optic cable. is a stand-MC-1
alone media converter
Installation . . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . .7
Cable Specifications . . . . . . . . . . .9
Technical Specifications . . . . . . .11
Troubleshooting . . . . . . . . . . . . .12
Contact Us . . . . . . . . . . . . . . . . .13
Compliance Information . . . . . . .15
MC-1 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1310 nm single mode
10 km *(6.2 miles)
*Typical maximum cable distance. Actual
distance is dependent upon the physical
characteristics of the network installation.
2BSS Audio 800-931-2357 8760 South Sandy Parkway, Sandy, Utah 84070 www.bssaudio.com 800-931-2357 3
Installation
Set the 6-position switch
The 6-position switch is located
on the side of the media
converter.
•Use a small flat blade
screwdriver to set the
recessed switches.
•All switches are shown in
the default position, UP.
Note: Switch positions S2 and S3 work together to configure the media
converter for Pause conditions.
S1 Remote-Fault Detection
up Disabled
down Enable
S2 & S3 work in combination
Pause
10 sw position 2 up and 3 down: Symmetric
01 sw position 2 down and 3 up: Asymmetric
11 sw positions 2 and 3 up: Pause is OFF (default position)
00 sw positions 2 and 3 down: Symmetric and Asymmetric
S4 Transparent Link Pass-Through
up Enable Link Pass-Through
down Disable Link Pass-Through
S5 Fiber Auto-Negotiation
up Disable Fiber Auto-Negotiation for the fiber link
(default setting)
down Enable Fiber Auto-Negotiation for the fiber link
S6 Loop Back
up Disable RX/TX signal loop back (default setting)
down Enable RX/TX signal loop back
2. Pause (symmetric)
3. Pause (asymmetric)
4. Transparent Link Pass-Through
5. Auto-Negotiation
1. Remote Fiber Fault Detect
6. Loop Back
4
Installation -- Continued
Install Mode
During installation, set converter DIP switch 4 DOWN; leave all other switches
in the UP position . This disables Transparent Link Pass-Through and(default)
Auto-Negotiation, allowing individual copper and fiber links to be established
(both copper port LEDs will turn ON with each device-to-device connection)
independent of a complete end-to-end connection.
Operation Mode
After installation is complete (all copper and fiber ports connected and linked),
set all switches to the UP position .(default))
Fiber Auto-Negotiation
Fiber Auto-Negotiation allows the fiber interface to detect and then advertise the
supported features of the remote device; this occurs only when a fiber cable is
connected to a device with a negotiating port. The process is as follows:
1. The fiber interface detects the supported features of the remote partner.
2. These abilities are passed to the twisted-pair interface and advertised.
3. Once the twisted-pair interface has a link at the highest common
capability, it passes the result to the fiber interface.
4. The fiber interfaces then start advertising these capabilities. At this point,
the link between the fiber and the negotiating port is complete.
If the MC-1 is connected via fiber to another MC-1, both media converters
must have the Fiber Auto-Negotiation setting disabled (switch5 UP).
Note: Transparent Link Pass-Through cannot be(switch position 4 enabled)
turned OFF ( when Fiber Auto-Negotiation is ON disabled) (enabled).
5
Installation -- continued
Install the fiber cable
1. Locate a 1000Base-SX/LX compliant fiber cable with male, two-stranded
TX to RX connectors installed at both ends.
2. Connect the fiber cables to the MC-1 media converter as
described:
•Connect the male TX cable connector to the female TX port.
•Connect the male RX cable connector to the female RX port.
3. Connect the fiber cables to the other device (another media converter,
hub, etc.) as described:
•Connect the male TX cable connector to the female RX port.
•Connect the male RX cable connector to the female TX port.
RX
TX TX
RX
Device Device
BSS Audio 800-931-2357 8760 South Sandy Parkway, Sandy, Utah 84070 800-931-2357 www.bssaudio.com

Product specificaties

Merk: BSS Audio
Categorie: Niet gecategoriseerd
Model: Soundweb London MC-1

Heb je hulp nodig?

Als je hulp nodig hebt met BSS Audio Soundweb London MC-1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd BSS Audio

BSS Audio

BSS Audio DPR-402 Handleiding

14 November 2023
BSS Audio

BSS Audio FDS-310 Handleiding

14 November 2023
BSS Audio

BSS Audio Soundweb 9010 Handleiding

14 November 2023
BSS Audio

BSS Audio MSR-602 Handleiding

14 November 2023
BSS Audio

BSS Audio FCS-966 Handleiding

14 November 2023
BSS Audio

BSS Audio FDS-355 Handleiding

14 November 2023
BSS Audio

BSS Audio DPR-944 Handleiding

13 November 2023
BSS Audio

BSS Audio Soundweb 3088 Handleiding

13 November 2023
BSS Audio

BSS Audio FCS-960 Handleiding

13 November 2023
BSS Audio

BSS Audio DPR-522 Handleiding

13 November 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic

Panasonic NB-W250 Handleiding

25 November 2024
Alpine

Alpine CHM-S611 Handleiding

25 November 2024
AOpen

AOpen DE3650-C Handleiding

25 November 2024
Lazer

Lazer Urbanize MIPS Handleiding

25 November 2024
Symmons

Symmons Dia 353GB-24 Handleiding

25 November 2024
SoundTube

SoundTube IPD-RS62-EZ Handleiding

25 November 2024
Moen

Moen Camerist 4905 Handleiding

25 November 2024
Lazer

Lazer Cameleon DLX Handleiding

25 November 2024
DMT

DMT DLD-85 Handleiding

25 November 2024
AOpen

AOpen AM1120T Handleiding

25 November 2024