BSS Audio Soundweb London FDS-388 Handleiding

BSS Audio Speaker Soundweb London FDS-388

Lees hieronder de 📖 handleiding in het Nederlandse voor BSS Audio Soundweb London FDS-388 (66 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/66
1
2
V2.0 DEP/JMK 15 May 1997
We have written this manual with the aim of helping installers and sound engineers to get to grips with the
Omnidrive and obtain its maximum capability. If you are new to BSS products, we recommend that you begin
at the start of the manual.
We welcome any comments or questions regarding the Omnidrive or other BSS products, and you may contact
us at the address or World Wide Web site given in the warranty section.
This equipment has been tested and found to comply with the following European and international Standards
for Electromagnetic Compatibility and Electrical Safety:
Radiated Emissions (EU): EN55013 (1990) Associated Equipment
RF Immunity (EU): EN50082/1 (1992) RF Immunity, Fast Transients ESD
Mains Disturbance (EU): EN61000/3/2 (1995)
Electrical Safety (EU): EN60065 (1993)
Radiated Emissions (USA): FCC part 15 Class B
Electrical Safety (USA): UL813/ETL (1996) Commercial Audio Equipment
Electrical Safety (CAN): UL813/ETLc (1996) Commercial Audio Equipment
IMPORTANT SAFETY INFORMATION
DO NOT REMOVE COVERS. NO USER SERVICABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. THIS EQUIPMENT MUST BE EARTHED.
IT SHOULD NOT BE NECESSARY TO REMOVE ANY PROTECTIVE EARTH OR SIGNAL CABLE SHIELD
CONNECTIONS TO PREVENT GROUND LOOPS. ANY SUCH DISCONNECTIONS ARE OUTSIDE THE
RECOMMENDED PRACTISE OF BSS AUDIO AND WILL RENDER ANY EMC OR SAFETY CERTIFICATION
VOID.
For continued compliance with international EMC legislation ensure that all input and output cables are wired
with the cable screen connected to Pin 1 of the XLR connectors and/or the jack plug sleeve. The input XLR Pin
1 and the side-chain input jack socket sleeve are connected to the chassis via a low value capacitor, providing
high immunity from ground loops whilst ensuring good EMC performance.
3
Quick Start
Quick Reference
Quick Start - Quick Reference
1 Check the Mains Voltage setting on the rear of the FDS-388/380 Omnidrive and
install into a rack. Connect the mains to the unit and check that it powers up.
2 Connect the two audio inputs and up to eight audio outputs. Do not put any audio
through the unit at this time.
Refer to Sections 2.0 thru 2.7 'Installation'
1 The user will need to load a program suitable for the PA system in use. Some units
will come locked to a specific PA system. In this case most controls will be disa-
bled and the unit will be ready for use. If the unit has a blank display or 'OWNER'
on the default screen, then the unit has been pre-programmed and software
locked and is also ready for use.
2 If the FDS-388 is not locked in one of these ways, the user may need to load a
program specific for the PA system by recalling it from memory or by loading a
file from a smart card. Alternatively recall program 0 (default) and program as in 5
below.
3 To load a file from memory press RECALL while in the default screen; the first
screen after the logo has disappeared. Use the parameter wheel to scroll through
the available programs. Programs marked with diamonds are "OEM" programs and
have been designed to match specific PA systems. Press the RECALL key again to
recall the selected program. If there is no program suitable then the user will need
to set up the unit from scratch to suit the PA manufacturers specification after
recalling program 0, or obtain a program on a smart card.
4 To load a file from smart card press RECALL while in the default screen. Press the
middle soft key on the left of the display. Turn the encoder to make the middle soft
key show 'Cprg' (Card program). Press the top soft key ('PICK') and turn the
encoder to select the program from the card. A second press of RECALL will load
the program. The user should now store the settings in internal memory for future
use. Refer to Section 15.0, Store Screen.
5 To adjust individual band levels, use the front panel trim controls.
For information on the FDS-380 Install version of the Omnidrive Refer to Section 21.0,
FDS-380 Install.
1 Set the Midi channel number of the FDS-380 Omnidrive Install using the two
recessed keys at the left hand end of the unit. To load a complete XAL file the file
should be named LOADmm.XAL where mm is the midi channel number e.g.
LOAD01.XAL if the unit's midi channel is 1. The file will be loaded when the card
is inserted into the card slot - the user is given a 3 second warning countdown
before the contents of the FDS-380 are overwritten. If the filename is wrong, an
error number will be displayed. Refer to Section 21.0 FDS-380 Install.
Please Read Overleaf...
FDS-380
Install
FDS-388
Omnidrive

Product specificaties

Merk: BSS Audio
Categorie: Speaker
Model: Soundweb London FDS-388

Heb je hulp nodig?

Als je hulp nodig hebt met BSS Audio Soundweb London FDS-388 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Speaker BSS Audio

BSS Audio

BSS Audio Soundweb London FDS-388 Handleiding

13 November 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Kramer

Kramer Tavor 8-Sub Handleiding

21 November 2024
Kramer

Kramer Galil 6-AW Handleiding

21 November 2024
Extron

Extron SM 28 Handleiding

21 November 2024
JBL

JBL RM10 Handleiding

20 November 2024
JBL

JBL Performance IS6 Handleiding

20 November 2024
JBL

JBL Power P-Kit Handleiding

20 November 2024
JBL

JBL Performance P941 Handleiding

20 November 2024
JBL

JBL Performance P52OWS Handleiding

20 November 2024
JBL

JBL Performance PC600 Handleiding

20 November 2024
JBL

JBL Performance IS6DT Handleiding

20 November 2024