Brother LX-570 Handleiding
Brother
Lamineersysteem
LX-570
Lees hieronder de 📖 handleiding in het Nederlandse voor Brother LX-570 (9 pagina's) in de categorie Lamineersysteem. Deze handleiding was nuttig voor 61 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/9
Cutter. The cutter is for trimming the
backing material and slides on the
cutter bar. It can be replaced.
Knob
Cutter bar
Latch (opens top cover)
Feed Deck. The LX-570 is designed for
use with items up to five inches wide. It
works best with item thicknesses
between 20 pound bond paper and 100
pound card stock or construction paper
(min. thickness is 0.004 inches, max.
thickness is 0.010 inches).
The LX-570 applies an adhesive, laminate, or
magnetic backing to an item without using heat or
electricity. You choose a backing by swapping the
drop-in cartridge.
The LX-570 comes with a starter cartridge already
installed. This cartridge applies a permanent
adhesive backing and is shorter than replacement
cartridges.
See the reverse for available cartridges and for
application ideas on using your LX-570. First, take a
few minutes to read these instructions.
Top Cover. Your LX-570
comes with a "starter"
cartridge already
installed, which applies a
permanent adhesive
backing to an item.
Cut:
When the item clears the cutter at the exit
area, gently push down on the cutter knob
and slide it all the way to the left or right.
Insert the item:
Insert the item face up at the feed
deck and turn the knob in the direction
of the arrows only; do not turn knob
backwards.
To avoid wasting the backing material,
note the location of the cut. Feed only
enough material to clear the cutter.
How to Use the LX-570
Insert the item
and be sure it
is straight.
Insert until you
feel contact;
then release it
as you turn
knob.
Exit area
When Using the
Starter Cartridge...
Feed and cut the item as described here. Be
sure to feed face up.
Press down firmly around all the edges. This
action prevents adhesive from remaining on
the front of the item. Then remove the clear
film and discard carefully as it is sticky.
When you are ready to place the item on a
surface, peel it from the white backing.
This starter cartridge contains five feet of
backing material. After you use it a few times,
always make certain that it contains sufficient
material. If uncertain, install a new cartridge
to avoid partial processing.
Note: the starter cartridge is shorter than the
replacement cartridges. See the other side
for cartridge descriptions and lengths. Always
consult packaging of replacement cartridges.
User’s Guide
12
LX-570 About the LX-570
Feed straight, not at an angle.
Turn the knob forward only.
Notes:
Before using, remove the protective tape
and other packaging materials under the
top cover.
Under the terms of an agreement with
Xyron, Inc., the purchase or
other acquisition of this product confers
no right or license to use
the product in the Retroreflective Field.
How to Change the Cartridge
Remove the cartridge:
Lift up the latch to open the top cover. Then
grasp the cartridge in one hand, hold the
LX-570 with the other, and lift the cartridge
up and out.
Insert a cartridge:
Open the top cover and lower
the cartridge in with the label up,
facing the feed deck.
As you lower the cartridge, be
sure that the backing material
fits underneath the cutter bar at
the exit area.
Close the top cover by gently
pushing down until it clicks and
is fully seated.
1
1
1
11
Unsnap the cutter:
Place your thumb underneath the back of the
cutter knob and your index finger on the cutter
bar. Lift up with your thumb to unsnap the cutter
from the cutter bar.
How to Change the Cutter
or must be run across the
backing material several times.
below). Or replace the cutter.
Blade is at this end and fits into
a groove on the cutter bar.
Always avoid touching the
blade.
Snap the new cutter into place:
At any point on the cutter bar, place the front
of the cutter into the groove on the cutter bar
so the blade fits into it. Then rotate the cutter
back and snap down.
Blade is at front of cutter.
Avoid touching the blade.
Back of cutter
Front of cutter
Guide the backing
material under the cutter
bar into the exit area.
Notes: When placing a partially-used
cartridge back in the machine, be sure
the material does not adhere to the
cartridge itself.
When removing a used cartridge
whose material has wrapped around
the rollers, remove the cartridge and
pull the material from the rollers.
Groove in cutter bar
1
1
1
11
1
1
1
11
2
2
2
22
2
2
2
22
When installed properly, the cutter slides
back and forth on the cutter bar.
The cartridge is properly installed when
the label is flush with the feed deck.
Close the top cover before using.
US5022001
Never place your finger under the cutter bar at the cutter. When
handling cutters, take care to avoid injury to yourself or others.
Avoid ingestion of the backing material or cutter.
Avoid contact of adhesive backing materials with skin or other
delicate surfaces.
Keep fingers out of the top cover when closing.
Warnings & Cautions
Warnings:
Cautions:
All backing materials are permanent once applied and cannot be
removed without damage. Do not use on single-source items.
Once you start feeding an item, do not try to back it out by
turning the knob in the opposite direction.
Always feed items straight, not at an angle.
Before processing an item, make certain that the cartridge contains
sufficient backing material. If uncertain, install a new replacement
cartridge to avoid partial processing.
When using the magnetic cartridge, do not place close to computer
diskettes or other sensitive materials.
Avoid exposure to excessive heat or moisture or dusty
environments. Do not place foreign objects inside or heavy objects
on top of the unit.
When discarding any portion of this product, check with local solid-
waste officials for recycling options or proper disposal methods.
For best results, be sure that all items are clean and free of debris
before inserting in the LX-570.
The LX-570 is not designed for use with thermal paper.
Do not disassemble, or the warranty will be void. Use only Brother
parts and accessories.
Product specificaties
| Merk: | Brother |
| Categorie: | Lamineersysteem |
| Model: | LX-570 |
Heb je hulp nodig?
Als je hulp nodig hebt met Brother LX-570 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Lamineersysteem Brother
12 Mei 2023
5 Mei 2023
2 April 2023
12 Maart 2023
24 Februari 2023
26 Januari 2023
Handleiding Lamineersysteem
- Lamineersysteem Quigg
- Lamineersysteem DESQ
- Lamineersysteem Ednet
- Lamineersysteem Fellowes
- Lamineersysteem GBC
- Lamineersysteem Hama
- Lamineersysteem Hema
- Lamineersysteem Konig
- Lamineersysteem Leitz
- Lamineersysteem Lervia
- Lamineersysteem Marquant
- Lamineersysteem Nedis
- Lamineersysteem Powerfix
- Lamineersysteem Renkforce
- Lamineersysteem Royal Sovereign
- Lamineersysteem Sencor
- Lamineersysteem United Office
- Lamineersysteem Olympia
- Lamineersysteem Exibel
- Lamineersysteem Tracer
- Lamineersysteem Genie
- Lamineersysteem Aurora
- Lamineersysteem Q-CONNECT
- Lamineersysteem Pavo
- Lamineersysteem Peach
- Lamineersysteem Rexel
- Lamineersysteem GFP
- Lamineersysteem SEAL
Nieuwste handleidingen voor Lamineersysteem
5 November 2024
5 November 2024
20 Oktober 2024
8 Augustus 2024
8 Augustus 2024
8 Augustus 2024
8 Augustus 2024
8 Augustus 2024
2 Juli 2024
16 April 2024