BOYA BY-WHM8 Pro Handleiding

BOYA Microfoon BY-WHM8 Pro

Lees hieronder de 📖 handleiding in het Nederlandse voor BOYA BY-WHM8 Pro (2 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

www.boya-mic.com

Too much

ambience is

being picked

up.

When using an omnidir-

ectional microphone like

the one included with

this system, the

microphone may be

picking up too much

ambience.

Make sure the microphone is as

close as to the subject as possible.

Specications：

System

Troubleshooting

If you have any problem using the BY-WM8 Pro components, use

the following checklist.

If any problem persist, please consult our local dealer, or contact

us directly.

Symptom Meanings Remedy

The units does

not turn on

The polarity orientation of the

batteries in the battery

compartment is incorrect.

The batteries are exhausted. Replace the batteries with

new ones.

The battery terminals in the

transmitter are dirty

Clean the + and - terminals

with cotton swab.

Insert the batteries with the

correct polarity orientation.

The batteries

become drained

quickly.

The batteries are exhausted. Replace the batteries with

new ones.

Manganese batteries are being

used.

Use alkaline batteries. The

battery life of a manganese

battery is less than half that

of an alkaline battery.

The BY-WM8 Pro components

is being used under cold

conditions.

The batteries drain quickly

under cold conditions.

The channel

cannot be

changed

An attempt was made to

change the channel by

pressing the SET button only.

There is no

sound.

The channel setting on the

transmitter is dierent from

that on the receiver.

Use the same channel setting

on both the transmitter and

receiver.

The sound is

weak.

The attenuation level

on the transmitter is

too high.

The input level of the transmitter

is low. Press the button on the

transmitter in attenuation level

setting mode to decrease the

attenuation level.

The line input is selected

on the transmitter. Pull the cable out from LINE IN.

There is

distortion in the

sound

There is

distortion in the

sound

The attenuation level on

the transmitter is too low.

The input level of the receiver is

extremely high. Press the + button

on the transmitter in attenuation

level setting mode to increase the

attenuation level.

The transmitter and the

receiver are set to

dierent channels.

Set the transmitter to the

same channel.

Headphones with a mon-

aural min jack is used.

Use the headphones with a

stereo mini jack.

RF interference

.Try a dierent channel. Make sure

both units are on the same

channel.

.Try to position the antennas at a

45° angle in relation to each other.

There can be a lot of RF

interference outdoors.

.Try moving indoors, where there

is less RF interference.

.Keep the units' antennas at least

2'(0.6m) away from conductive

objects like metal and water.

.Overhead telephone lines,

uorescent lighting, and metal

fences can all cause interference.

.Turn o all nearby computers

and mobile phones.

The audio is

noisy or

distorted. This

can include drop

outs, white

noise, bursts,

pops and clicks.

The audio is

noisy or

distorted. This

can include drop

outs, white

noise, bursts,

pops and clicks.

RF signal is weak.

Make sure there is an unobstructed

line of sight between the

transmitter's and the receiver's

antennas.

Keep in mind that your body,

clothes, and onstage sets are

possible obstructions.

Make sure the receiver and

the transmitter are within

328'(100m) range.

If there are obstructions, you

may need to move closer.

The input level on the

camera, recorder, or

mixer is too high.

Turn down the audio input level on

your camera or recording device.

Lower the audio output level on

the receiver.

Turn down the gain on your mixer.

If there is no adjustment on the

device, and the level is still high,

adjust the microphone level on the

transmitter. Keep this level as high

as possible without distortion.

38 39 40

44 45

41 42

Restart the unit, then change

the channel with the + and -

buttons.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired operation.

Warning: Changes or modications to this unit not expressly

approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: “This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmfulinterference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment o and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit dierent from

that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC STATEMENT:

RF warning statement:

The device has been evaluated to meet general RF exposure requirement.

The device can be used in portable exposure condition without restriction.

Transmitter B

Frequency Chart

Transmitter A

C hannel (C H) Frequenc y(MH z) C hannel(C H) Frequenc y(MH z)

1 556.710

2 557.120

3 557.530

4 557.940

5 558.350

6 558.760

7 559.170

8 559.580

9 559.990

10 560.400

11 560.810

12 561.220

13 561.630

14 562.040

15 562.450

16 562.860

17 563.270

18 563.680

19 564.090

20 564.500

21 564.910

22 565.320

23 565.730

24 566.140

25 566.550

26 566.960

27 567.370

28 567.780

29 568.190

30 568.600

31 569.010

32 569.420

33 569.830

34 570.240

35 570.650

36 571.060

37 571.470

38 571.880

39 572.290

40 572.700

41 573.110

42 573.520

43 573.930

44 574.340

45 574.750

46 575.160

47 575.570

48 575.980

C hannel(C H) Frequen cy(M H z) C hannel(C H) Frequenc y(M Hz)

1 576.390

2 576.800

3 577.210

4 577.620

5 578.030

6 578.440

7 578.850

8 579.260

9 579.670

10 580.080

11 580.490

12 580.900

13 581.310

14 581.720

15 582.130

16 582.540

17 582.950

18 583.360

19 583.770

20 584.180

21 584.590

22 585.000

23 585.410

24 585.820

25 586.230

26 586.640

27 587.050

28 587.460

29 587.870

30 588.280

31 588.690

32 589.100

33 589.510

34 589.920

35 590.330

36 590.740

37 591.150

38 591.560

39 591.970

40 592.380

41 592.790

42 593.200

43 593.610

44 594.020

45 594.430

46 594.840

47 595.250

48 595.660

PLL Synthesized Control Oscillator

556.71 MHz-575.98 MHz (Transmitter A)

576.39 MHz-595.66 MHz (Transmitter B)

40 Hz to 18 kHz (+/-3dB)

14° F to 122° F (-10 to +50 )℃ ℃

14° F to 131° F (-10 to +55 )℃ ℃

Oscillator type:

Carrier Frequency Range:

Channels:

Frequency response:

Operating temperature:

Storage temperature:

RF output power

Antenna

Spurious emission

Audio input connector

Reference audio input level

Reference deviation

Input frequency range

Distortion

Power supply

Dimensions:

Weight:

≤10 mW

1/4λ wire antenna

250nW or less

3.5mm jack

–60 dBV (MIC input, 0 dB attenuation)

±5 kHz (–60 dBV, 1 kHz input)

20Hz-20KHz

0.5% or less

Two AA size batteries

TX8 PRO:20.8 x 6.7 x 2.9 cm

BY-WXLR8 PRO:5.7x4.55x11.69cm

BY-WHM8 PRO: 5.3x5.3x25.6cm

TX8 PRO:81g (without batteries)

BY-WXLR8 PRO:162g (without batteries)

BY-WHM8 PRO: 252g (without batteries)

Receiver:

Lavalier Microphone

Antenna

Audio output connector

Signal to noise ratio

Distortion

Headphone output level

Audio output level

Power supply

Dimensions

Weight

1/4λ wire antenna

3.5mm jack

80dB or more

0.5% or less

30mW (16 Ω)

–60 dBV

Two AA size batteries

208 H × 67 W × 29 L mm ( ) ( ) ( )

95g without batteries

Back electret Condenser

Omni-directional

35Hz ~ 18 KHz

74dB SPL

-30dB +/-3dB / 0dB=1V/Pa, 1 kHz

3.5mm locking mini plug

1.2m (4’)

Transducer:

Polar pattern:

Frequency Range:

Signal / Noise:

Sensitivity:

Connector:

Length:

SHENZHEN JIAYZ PHOTO INDUSTRIAL., LTD.

The BOYA logo is a trademark which is registered and owned by

Shenzhen Jiayz Photo Industrial., Ltd.

COPY RIGHT 2010-2020

Email: sales@boya-mic.com

www.boya-mic.com / www.jiayz.com

Important Notes

Usage and storage

Operating the BY-WM8 Pro components near electrical equipment

(motors, transformers, or dimmers) may cause it to be aected

by electromagnetic induction.

The presence of the lighting equipment may produce electrical

interference over the entire frequency range. Position the

BY-WM8 Pro components so that interference is minimized.

To avoid degradation of the signal-to-noise ratio, DO NOT use the

BY-WM8 Pro components in noisy

Places or in locations subject to vibration, such as the following:

- Near electrical equipment, such as motors, transformers, or dimmers.

- Near air condition equipment or places subject to direct air flow from

an air conditioner.

- Near public address loudspeaker.

- Where adjacent equipment might knock against the receiver.

Cleaning

Clean the surface and the connectors of the BY-WM8 Pro components

with a dry, soft cloth. Never use thinner, benzene, alcohol or any

other chemicals, since these may mar the nish.

33 34 35 36 37

BY-WHM8 Pro

Wireless Handheld Microphone

4. PAIR

A. How to change Channel

1) Short press “PAIR” botton, the channel number blinks

2) Press “PAIR” botton again to change channel.

3) Wait 3 seconds till channel number doesn’t blink.

B. Long press “PAIR” botton to change Channel “A” or “B”.

5. Battery compartment

6. Battery cover

1. Power LED

2. LCD screen

For more details, please refer to “LCD Display Operation Guide”

on page 35.

3. Power OFF/ON

Installing Batteries

The transmitter is each powered by two AA batteries. To install

batteries, please follow these steps:

1. Turn the battery cover anti-clockwise to unscrew.

2. Push the “OPEN” bottom down.

3. Insert the batteries in the right polarity as shown.

4. Close the battery cover and retighten it by screwing clockwise

until it is reasonably tight.

NOTE:

1. Please make sure the units is turned OFF, because taking out the

battery compartment during signal transmission may cause high

noise.

2. Please remove the batteries from the microphone when the

microphone is not in use as current is drawn whenever a battery

is installed.

① ）Channel Group (A/B

Long press “SET” botton to change Channel “A” or “B”

②Channel number (1-48)

③Battery indication

Connecting the wireless handheld microphone and the

receiver

To connect the wireless handheld microphone and the receiver,

follow these steps:

1. Turn on the wireless handheld microphone and the receiver.

2. Set the wireless handheld microphone and the receiver to the

same channel.

If you are experiencing interference or noise on one channel, try

a dierent channel.

Product Structure

LCD Display Operation Guide

Keep the BY-WM8 Pro components as far as from such equipment

as possible.

TX8 PRO , BY-WXLR8 PRO, BY-WHM8 PRO

Product specificaties

Merk:	BOYA
Categorie:	Microfoon
Model:	BY-WHM8 Pro
Kleur van het product:	Zwart
Hoogte:	256 mm
Soort:	Microfoon voor interviews
Stroombron:	Batterij/Accu
Connectiviteitstechnologie:	Draadloos
Diameter:	53 mm
Ondersteund aantal accu's/batterijen:	2
Aansluiting:	RF
Microphone direction type:	Unidirectioneel
Spreekspoel types:	Dynamisch
Frequentie microfoon:	20 - 20000 Hz
Type beeldscherm:	LCD
Type batterij:	AA
RF vermogen:	10 mW
Gewicht microfoon:	252 g
Microfoon Signal-to-Noise Ratio (SNR):	80 dB
Microphone Total Harmonic Distortion (THD):	0.5 procent
Kanalen:	48