Boss SB18BRGB Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Boss SB18BRGB (2 pagina's) in de categorie Soundbar. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Thank you for purchasing this
SB18BRGB Sound Bar
Please read through these instructions carefully so you will know
how to operate your model properly.
After you have nished reading the instructions, keep this document
in a safe place for future reference.
Before You Start
Read and understand all instructions before you use your product. If you do not follow the instructions
in this manual, we are not responsible for injury or damage resulting from improper handling. This will
also void the warranty.
Important Safety Precautions
• Be sure to observe the following guidelines:
- Do not increase speaker volume so high that you cannot hear what is around you.
- Use caution or temporarily discontinue use in potentially hazardous situations.
• Do not make any adjustment on the product when driving or in other situations where distractions can be
hazardous. Responsible and safe driving is your primary responsibility when operating a vehicle.
• Start volume at a low setting then gradually increase the volume until you can hear it comfortably, without
sound distortion and ear discomfort.
• In the event of smoke, strange noise or odor emitted from the product or any other abnormal operational
signs appearing on the product, disconnect the product from the power supply. Discontinue use and contact
your dealer or our technical support. Using the product in this condition may result in permanent damage to
the system.
• Servicing must only be carried out by a technician. Contact our technical support for any service questions.
Installation Precautions
• WARNING: Always consult a professional installer.
• Installation must be performed by a professional. Contact our technical support for any installation questions.
• Observe the safety and operating instructions of the devices which are connected to the product.
• Only use attachments/accessories specied by the manufacturer for installation.
• Do not modify this product, as this affects the safety of the product and creates a risk of injury.
• Before installation, disconnect the negative terminal of the vehicle battery to prevent damage to the product,
re, and/or possible injury.
Care for Your Product
• DO NOT clean the product in hot weather (e.g. hot sunlight).
• DO NOT use abrasive or highly alkaline cleaner on the product.
• DO NOT use gasoline, acetone, carbon tetrachloride or other aggressive chemical solutions on the product.
• DO NOT scrape the product with razor blade or other sharp instrument.
• DO NOT use a pressure washer or pressurized water.
• This product is water resistant. However, never submerge the product in water.
Mounting
Mounting on ATV or UTV
Always consult an expert when in doubt about the installation.
You must work with an assistant to mount the sound bar due to its heavy weight.
Use only the supplied accessory for mounting. Using other mounting methods may void the warranty.
To ensure security of the mounted sound bar, always check the mounting conditions (e.g. clamp
fastening) of the sound bar before each vehicle ride.
2
Spring washer
Upper clamp
Lower clamp
Rubber strip
Mounting bar
(Ø 1.75” − 2”)
Lower clamp
Sliding block
1
3
4
Power Connection
Option 1: Using Power Port
If your vehicle has a 12V power port, directly connect the sound bar to your vehicle for power connection.
1. Insert the 12V power port plug of the sound bar into your vehicle power port.
Note: To avoid battery drain, it is recommended to unplug after each use (if the port power is not switched
off with the ignition key).
To your vehicle power port
12V power port plug with 10A fuse
Option 2: Using Power Port Plug Adapter
If your vehicle dose not have a 12V power port, use the supplied power port plug adapter for connection to
your vehicle battery.
Important:
• To avoid short circuits and any resulting damage to the sound bar, the negative terminal of the vehicle battery
must be disconnected rst.
1. Connect the black/ground wire of the power port plug adapter to the vehicle’s metal frame or to the negative
battery terminal. Fasten the ground wire with a bolt/screw on the metal surface. Make sure the metal surface
is clean with no paint, rust or dirt.
2. Connect the red wire of the power port plug adapter to the positive battery terminal.
If needed, use extension wires of 12-14 gauge for connection to the battery. Remember to install a 15A
in-line fuse (not included) and an on/off switch (not included). An on/off switch is not needed if you
unplug the sound bar after each use or if the vehicle power port is turned off with the ignition key. Refer to
the illustration.
3. Insert the power port plug of the sound bar into the power port plug adapter.
2
THIS PACKAGE CONTAINS
1x SB18BRGB sound bar
Mounting kit + 1x Hex wrench
1x 12V power port plug adapter
1x Remote control + 1x Keychain
1x User manual + 1x Warranty card
IMPORTANT
Please enter below the Serial No. which is located on the exterior of the product. Retain this
information for future reference.
Model
Serial No.
Date of Purchase
Getting to Know Your Sound Bar
Introduction
The product is a Bluetooth speaker system which is ideal for installation in an ATV (All Terrain Vehicle) or UTV
(Utility Vehicle). You can stream audio from a mobile phone to this product via Bluetooth. You can also play music
les stored in a USB ash drive, and music from an external device (e.g. a mobile phone or MP3 player) can be
played via 3.5mm AUX input jack.
You can output audio from the sound bar to an external amplier or powered speakers through RCA output.
The product is integrated with LED lights which can be controlled using the supplied lighting controller.
This product is shockproof and water resistant. This product is designed to be operated with 10-16 VDC negative
ground vehicle power supply only. Never connect this product to any other voltage supply (e.g. 24 VDC).
Product Overview
1 2 3
49
8
7
6
10
5
1 3.5mm audio input jack
2 RCA audio output sockets
3 USB port
4 12V power port plug with 10A fuse
5 Power button (hold down to power on or off);
Mode button
6 Volume buttons
7 Start/pause/resume play button
8 Track selection buttons
9 Remote sensor (aim the remote control directly
at the sensor when using the remote controller)
10 Display
3
4 5 Power Connection
Vehicle’s metal frame
Black wire
12V power port plug with 10A fuse
Power port plug adapter
Red wire
Battery Fuse
(not included) 1
2
On/Off switch
(not included)
3
Option 3: Direct connection to vehicle battery
Important:
• To avoid short circuits and any resulting damage to the sound bar, the negative terminal of the vehicle battery
must be disconnected rst.
1. Remove the plug from the supplied power port plug cable.
2. Connect the power port plug’s negative wire to the vehicle’s metal frame or to the negative battery terminal,
and the power port plug’s positive wire to the positive battery terminal.
• To prevent electrical damage, you must install 1) a 15A fuse (not included) and 2) an on/off switch (not
included) to be in line with the power wire which connects to the positive battery terminal.
• Fasten the ground wire with a bolt/screw on the metal surface. Make sure the metal surface is clean with no
paint, rust or dirt.
Turn on or off
• Press and hold on the sound bar (or on the remote control) to turn on or off the sound bar. When turned
on, the power LED indicator illuminates on the power port plug.
• on the remote control to turn on or off the LED lights.Press briey
To avoid battery drain when the sound bar is not used, disconnect the sound bar from the battery by
unplugging the power port plug or using the inline on/off switch (not included).
6
1
1. Correctly orient the supplied sliding block, and attach
it to the bottom side of the lower clamp using the
supplied hex wrench. Make sure not to tighten the
block for subsequent slide into the groove.
2. Find the groove on the top panel of the sound bar.
Correctly orient the sliding block and slide it into the
groove from either end of the groove. Then slide the
clamp to a proper position and tighten it with the hex
wrench.
3. Attach the supplied rubber strips over the clamp and
cage bar for secure clamping and abrasion prevention.
4. Tighten the upper clamp to the lower clamp with the
hex wrench. Make sure the supplied spring washers
are used to provide more stable bolt fastening against
vibration.
Repeat the steps above to secure the sound bar with
the other clamp assembly.
SB18BRGB
0823
Bluetooth
Before you can stream music from your mobile device (iOS device or Android device) to the sound bar through
Bluetooth, pair the sound bar with your mobile device.
1. The sound bar automatically switches to Bluetooth mode when turned on. “bt” appears and ashes to
indicate that the sound bar enters pairing mode.
If Bluetooth mode is not activated, press MODE briey to select Bluetooth mode.
2. On your mobile device, enable Bluetooth function and select the device name (“Boss Audio SB18BRGB”) to
pair the sound bar with the mobile device. If prompted for password, enter “0000”.
If no Bluetooth device is paired within ten minutes, the sound bar will automatically exit pairing mode. In this
case, you need to repeat the steps above to re-enter the pairing mode.
Note: Only one device can be paired at a time.
3. When successfully paired/connected, “bt” on the display stops ashing and lights up. Play audio on your
mobile device, and audio will be streamed to the sound bar.
After pairing, the sound bar will be automatically connected to your mobile device each time the two are
turned on. To change Bluetooth source, disconnect the current Bluetooth connection by holding down for
two seconds then repeat the steps above to connect/pair with another mobile device.
11Playback control
• To pause or resume play, press .
• To select the previous or next track, press or .
• To adjust volume, press .VOL +/-
To maximize audio performance, set the volume of the connected device to a minimum of 75%.
Ideally, on the highest volume setting you can get without distortion.
To avoid battery exhaustion, make sure to run the vehicle engine when operating the sound bar.
Operational range can be reduced by any obstacle between the sound bar and the device.
If the connected device is out of the effective range from the sound bar, the device will be automatically
disconnected. The device will be automatically re-connected if it is back to the effective range.
7AUX
You can listen to an external audio device (e.g. MP3 player or a mobile phone) through the sound bar.
3.5mm
audio cable
AUX
input
1. Using an audio cable with 3.5mm plug (not included), connect the AUX input (3.5 mm) from the sound bar
to the headphone jack on your audio device.
2. The sound bar automatically switches to AUX mode when AUX connection is made. “AUX” is displayed.
If AUX mode is not activated, press briey to select AUX mode.MODE
3. Select and play audio les on your audio device. Audio from the connected device will be played on the
sound bar.
To maximize audio performance, set the volume of the connected device to a minimum of 75%.
Ideally, on the highest volume setting you can get without distortion.
Operating the sound bar consumes the vehicle battery. To avoid battery exhaustion, make sure to run
the vehicle engine when operating the sound bar.
12Playback control
• To pause or resume play, press .
• To adjust volume, press .VOL +/-
• To select the previous or next track, use the controls only on the connected device.
USB
You can enjoy audio stored on a USB storage device through the sound bar.
USB ash drive
USB port
1. Connect a USB ash to the USB port from the sound bar.
2. The sound bar automatically switches to USB mode when USB connection is made. “USB” is displayed
briey.
If USB mode is not activated, press MODE briey to select USB mode.
Music plays automatically.
MP3 and WMA les are playable. The USB port can provide 1A current for mobile device charging.
Operating the sound bar consumes the vehicle battery. To avoid battery exhaustion, be sure to run the
vehicle engine when operating the sound bar.
13Playback control
• To pause or resume play, press .
• To select the previous or next track, press or .
• To adjust volume, press .VOL +/-
Audio Output
You can output audio from the sound bar to an external amplier or powered speakers through RCA output.
RCA output sockets
Audio cable with RCA plugs
Fuse Replacement
If the power LED indicator on the power port plug does not illuminate, this indicates the fuse inside the power port
plug is blown. Replace the blown fuse with a new 10A AGC fuse (glass cartridge type).
1. Locate the screw cap on the front end of the power port plug. Turn counterclockwise the screw cap to open
then access the fuse inside.
2. Replace with a new fuse (not included). Then replace the power port plug while ensuring the contact head
sticks out.
Screw cap and contact head AGC fuse
12
Remote Control
The sound bar comes with a remote control. You can use the remote control to control both music playback
and the LED lights which are integrated with the sound bar.
Light control buttons
1Press and hold to turn the sound bar
on or off.
Press briey to turn lights on or off.
2MODE +/- Switch from static to dynamic illumination
and select a dynamic illumination pattern.
3SPEED +/- For dynamic illumination, select a dynamic
illumination speed.
4DEMO Cycle red, green and blue illumination.
5COLOR +/- Switch from dynamic to static illumination
and select an illumination color.
6BRIGHT +/- For static illumination, change the
illumination intensity.
7SYN Enable or disable lights ashing to music.
When enabled, SPEED buttons are invalid.
Playback control buttons
A / For Bluetooth and USB, select the
previous or next track.
BVOL +/- Increase or decrease volume.
CEQ For Bluetooth and USB, select a preset
sound mode.
DStart, pause or resume music play.
EMODE Select a mode (Bluetooth, AUX and USB).
17
C
D
3
A
B
2
4
56
E
CR2025 battery
replacement
+
12
Troubleshooting
If you have problems using this product, check the following points before you request service. If you still have
a problem, contact our technical support.
Problem Solution
Power off after beeping 3 times.
If the voltage runs below 8.5V or above 18.5V, the sound bar
will beep 3 times then automatically turn off to prevent battery
depletion or voltage-surge damage.
No power.
Power connection is not made. See the section “Power
Connection” for details.
The fuse inside the power port plug is blown. Replace the fuse.
The ACC switch of the vehicle is not on. Turn the ACC switch on.
No sound.
Press to select the correct audio input. MODE
Check the connected device for volume level or playback status
(e.g. pause or stop).
Cannot connect through Bluetooth.
The device is not paired with the sound bar. Pair the two (see
“Bluetooth” section).
Make sure the device is within range.
The sound bar is already connected with another Bluetooth
device. Disconnect the current Bluetooth connection.
Bluetooth has been disconnected for more than three minutes,
manually reconnect Bluetooth through your mobile device.
Audio quality from Bluetooth
connection is poor.
Move the device closer to the sound bar or remove obstacles or
sources of interference that are affecting Bluetooth reception.
No response. Power glitch or interference. Disconnect power for ten seconds
then reconnect power.
Environmental Care
Do not throw away the product with normal household waste at the end of its life. Follow your local laws if/
when disposing of electronic products. By doing this, you help preserve the environment.
8 9 10
11 12
Using an audio cable with RCA plugs
(not included), connect RCA sockets
from the sound bar to RCA inputs on an
amplier or powered speakers.
1Important notes on battery
• Observe correct polarity while inserting the battery. Replace only with the same type or equivalent type.
• Do not leave the battery under direct sunlight. This may cause re, explosion or excessive heat.
• Remove the battery from the remote control if not used for a long period of time.
• The remote control contains a coin/button type battery, which is a choke hazard. Keep the battery out of reach
of children at all times! If swallowed, the battery can cause serious injury or death.
Specications
Bluetooth
Bluetooth version ..............................................5.0 / EDR
Bluetooth proles A2DP, AVRCP ..............................................
Bluetooth frequency ..........................................2402 - 2480 MHz
Transmission power..........................................<4 dBm
Transmission distance ......................................up to 33 ft /10 m (line of sight)
Speakers
High power speaker .........................................2 x 4” (102 mm)
Tweeter .............................................................2 x 1” (25 mm), soft dome
Amplier
Amplier class ..................................................Class A/B, full range
Input impedance ...............................................10 kΩ
Frequency response .........................................45 Hz - 22 kHz
Connectivity
USB .................................................................. USB-A, MP3/WMA playable; USB charging (1A)
AUX 3.5 mm jack for audio input ..................................................................
RCA RCA sockets for audio output .................................................................
General
Input voltage ..................................................... 12 VDC (allowable 10 - 16 VDC)
Current draw .....................................................6A MAX
Fuse ..................................................................10A AGC type
Clamp size range (O.D.) ...................................1.75” - 2”
Weight ..............................................................8.2 lbs / 3.7 kg
Dimensions drawing
18”
(458 mm) (95 mm)
3.74”
4.88”
(124 mm)
4.88”
(124 mm)
13
Product specificaties
| Merk: | Boss |
| Categorie: | Soundbar |
| Model: | SB18BRGB |
Heb je hulp nodig?
Als je hulp nodig hebt met Boss SB18BRGB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Soundbar Boss
11 December 2024
15 Juni 2023
15 Juni 2023
11 Juni 2023
4 Juni 2023
4 Juni 2023
3 Juni 2023
3 Juni 2023
31 Mei 2023
30 Mei 2023
Handleiding Soundbar
- Soundbar Philips
- Soundbar HP
- Soundbar Sony
- Soundbar Samsung
- Soundbar Panasonic
- Soundbar Bticino
- Soundbar LG
- Soundbar Grundig
- Soundbar JVC
- Soundbar JBL
- Soundbar Karcher
- Soundbar Medion
- Soundbar Onkyo
- Soundbar Pioneer
- Soundbar Yamaha
- Soundbar Yealink
- Soundbar Aiwa
- Soundbar Akai
- Soundbar Altec Lansing
- Soundbar Auna
- Soundbar Avtex
- Soundbar Bigben
- Soundbar Blaupunkt
- Soundbar Bluesound
- Soundbar Bose
- Soundbar Boston Acoustics
- Soundbar Dali
- Soundbar Definitive Technology
- Soundbar Dell
- Soundbar Denon
- Soundbar Denver
- Soundbar Devialet
- Soundbar Elac
- Soundbar Ematic
- Soundbar Energy
- Soundbar Energy Sistem
- Soundbar FALLER
- Soundbar Fantec
- Soundbar GPX
- Soundbar Haier
- Soundbar Hama
- Soundbar Harman Kardon
- Soundbar Hisense
- Soundbar Ices
- Soundbar ILive
- Soundbar Insignia
- Soundbar Kicker
- Soundbar Klipsch
- Soundbar Kogan
- Soundbar Konig
- Soundbar Laser
- Soundbar Legamaster
- Soundbar Lenco
- Soundbar Livoo
- Soundbar Logic3
- Soundbar Mac Audio
- Soundbar Magnat
- Soundbar Maxell
- Soundbar MB Quart
- Soundbar Megasat
- Soundbar Monitor Audio
- Soundbar Mtx Audio
- Soundbar Muse
- Soundbar Nec
- Soundbar Nedis
- Soundbar Paradigm
- Soundbar Polk
- Soundbar Pure Acoustics
- Soundbar Pyle
- Soundbar Q Acoustics
- Soundbar Razer
- Soundbar Reflecta
- Soundbar Renkforce
- Soundbar Roku
- Soundbar Schneider
- Soundbar Selfsat
- Soundbar Sennheiser
- Soundbar Sharp
- Soundbar Sherwood
- Soundbar Silvercrest
- Soundbar Sonos
- Soundbar Sylvania
- Soundbar TCL
- Soundbar Technaxx
- Soundbar Teufel
- Soundbar Thomson
- Soundbar Trust
- Soundbar Vifa
- Soundbar Vizio
- Soundbar Wharfedale
- Soundbar Xoro
- Soundbar Jamo
- Soundbar OK
- Soundbar Orbitsound
- Soundbar Cambridge
- Soundbar Klip Xtreme
- Soundbar Continental Edison
- Soundbar Bang And Olufsen
- Soundbar Bowers And Wilkins
- Soundbar Creative
- Soundbar Edifier
- Soundbar GoGEN
- Soundbar Krüger And Matz
- Soundbar Monoprice
- Soundbar Naxa
- Soundbar NGS
- Soundbar Proscan
- Soundbar Steren
- Soundbar Voxicon
- Soundbar Infiniton
- Soundbar Nevir
- Soundbar Kubo
- Soundbar Trevi
- Soundbar Sven
- Soundbar Canton
- Soundbar Integra
- Soundbar Vision
- Soundbar Furrion
- Soundbar SunBriteTV
- Soundbar BlueAnt
- Soundbar Cabstone
- Soundbar Séura
- Soundbar Sonance
- Soundbar Bigben Interactive
- Soundbar Adj
- Soundbar Element
- Soundbar AV:link
- Soundbar Peerless-AV
- Soundbar Audac
- Soundbar Russound
- Soundbar Bazooka
- Soundbar Martin Logan
- Soundbar Nxg
- Soundbar Neets
- Soundbar AMX
- Soundbar Crestron
- Soundbar PSB
- Soundbar Wet Sounds
- Soundbar GOgroove
- Soundbar EKO
- Soundbar GoldenEar Technology
- Soundbar MusicMan
- Soundbar Astell&Kern
- Soundbar PowerBass
- Soundbar Thonet & Vander
- Soundbar Planet Audio
- Soundbar Memphis Audio
- Soundbar SoundTube
- Soundbar Edis
- Soundbar Fosi Audio
- Soundbar Majority
- Soundbar Aconatic
Nieuwste handleidingen voor Soundbar
9 December 2024
9 December 2024
9 December 2024
9 December 2024
9 December 2024
9 December 2024
8 December 2024
8 December 2024
5 December 2024
4 December 2024