Boss CEB-3 Handleiding

Boss Effect machine CEB-3

Lees hieronder de 📖 handleiding in het Nederlandse voor Boss CEB-3 (1 pagina's) in de categorie Effect machine. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

English

Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

7The BOSS CEB-3 is a chorus unit that is specically designed for electric bass guitar.

7The CEB-3 allows you to select the frequency band to which the chorus eect will apply. That is, you can have the eect applied to the overall sound, or only a specic frequency range if you wish.

7Using the two channel outputs, deeper chorus eects can be created with the “Space synthesis system.”

DC IN jack

Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can play

without being concerned about how much battery power you have left.

* We recommend that you keep batteries installed in the unit even though you’ll be powering it with

the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the AC adaptor

gets accidentally disconnected from the unit.

* Use only the specied AC adaptor (PSA-series).

* If the AC adaptor is connected while power is on, the power supply is drawn

from the AC adaptor.

Panel Descriptions

Main Features

E.LEVEL knob

This knob adjusts the level of the eect sound (in relation to the input signal).

Rotating the knob clockwise increases the level of the eect sound.

OUTPUT A (MONO)/OUTPUT B jacks

The output jacks are used to connect the unit to

ampliers or other devices.

* For mono output, use OUTPUT A jack. Both the dry

and processed signals are output.

* For stereo use:

OUTPUT A :

Only the processed signal (pitch modulated sound) is

output. The dry (unprocessed) signal is not output.

OUTPUT B :

Only the dry signal is output.

The CEB-3 adopts the “Space synthesis system” for stereo output.

That is, the depth of the eect varies depending on the distance between

speakers. Note that lowering a lter control knob or eect level too much

will shift the sound image to the OUTPUT B position, and therefore diminish

the eect. Experiment with dierent setting as you play the instrument.

CHECK indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.

The indicator lights when an eect is ON.

* If this indicator goes dim or no longer lights while an eect is ON, the battery is near

exhaustion and should be replaced immediately.

LOW FILTER knob

This knob controls the lower frequencies of the eect sound.

As you rotate the knob clockwise, the chorus eect will be applied to a wider

range of lower frequencies. Conversely, rotating the knob counterclockwise will

cut lower frequencies, causing only the upper frequencies to take on the chorus

eect.

Pedal Switch

This switch turns the eects ON/OFF.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change the

battery.

* For instructions on changing the battery, refer to “Changing the Battery.”

RATE (Modulation rate) knob

This knob adjusts the speed of the chorus eect. Rotating the knob clockwise

increases the speed.

DEPTH (Modulation depth) knob

This knob adjusts the depth of the chorus eect. Rotating the knob clockwise

deepens the eect.

Amplier

AC Adaptor

(PSA series; sold separately)

Precautions When Connecting

5 To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

5 Once the connections have been completed, turn on power to

your various devices in the order specied. By turning on devices

in the wrong order, you risk causing malfunction and/or damage

to speakers and other devices.

When powering up: Turn on the power to your bass amp last.

When powering down: Turn o the power to your bass amp rst.

5 Before turning the unit on/o, always be sure to turn the volume

down. Even with the volume turned down, you might hear some

sound when switching the unit on/o. However, this is normal and

does not indicate a malfunction.

Use of Battery

5 A battery is supplied with the unit. The life of this battery may be

limited, however, since its primary purpose was to enable testing.

5 If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY” and

“IMPORTANT NOTES” (supplied on a separate sheet).

5 When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

5 Batteries should always be installed or replaced before connecting

any other devices. This way, you can prevent malfunction and

damage.

Main Specications

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output

Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance 10 kΩ or greater

Power Supply Alkaline battery (9 V, 6LR61)

AC adaptor (PSA series: sold separately)

Current Draw 55 mA

* Expected battery life under continuous use:

Alkaline: 6 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight 420 g / 15 oz (including battery)

Accessories Leaet (“USING THE UNIT SAFELY,” “IMPORTANT

NOTES,” and “Information”)

Alkaline battery (9 V, 6LR61)

Options

(sold separately) AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

Electric bass

guitar

INPUT jack

This jack accepts input signals (coming from a bass guitar, some other musical

instrument, or another eect unit).

* The INPUT jack doubles as power switch.

Power to the unit is turned on when you

plug into the INPUT jack; the power is

turned o when the cable is unplugged.

When not using the eects unit, be sure

to disconnect the plug from the INPUT

jack.

Operating the Unit

1. When you have made the necessary connections, set

the knobs as shown in the illustration.

56 3 4

2. Depress the pedal switch to turn the eect on. (Make

sure that the CHECK Indicator lights.)

3. Adjust the speed of the chorus eect using the RATE

knob.

4. Adjust the depth of the chorus eect using the DEPTH

knob.

5. Using the LOW FILTER knob, adjust the frequency band

to which the chorus eect should be applied.

6. Adjust the volume of the processed sound using the

E.LEVEL knob.

Changing the Battery

1. Hold down the pedal and loosen the thumbscrew, then

open the pedal upward.

* The pedal can be opened without detaching the thumbscrew

completely.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

2. Remove the old battery from the battery housing, and

remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil

spring, and battery housing.

5. Finally, insert the thumbscrew into the guide bush

hole and fasten it securely.

Product specificaties

Merk:	Boss
Categorie:	Effect machine
Model:	CEB-3
Kleur van het product:	Black, Blue
Gewicht:	420 g
Breedte:	73 mm
Diepte:	129 mm
Hoogte:	59 mm
Gebruikershandleiding:	Ja
Type stroombron:	AC, Battery
Accu/Batterij voltage:	9 V
Ondersteund aantal accu's/batterijen:	1
Aansluiting voor netstroomadapter:	Ja
Stroomverbruik:	55 mA
Beste gebruik:	Gitaar
Type product:	Expressiepedaal
Synchronisatie ingangsimpedantie:	1000000 Ohm
Uitgang van 6,35 mm (1/4-inch):	2
Output impedance:	1000 Ohm
Ingang van 6,35 mm (1/4-inch):	1
Nominale input level:	-20 dB