Boss BCB-1000 Handleiding

Boss Receiver BCB-1000

Lees hieronder de 📖 handleiding in het Nederlandse voor Boss BCB-1000 (1 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 76 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

*5100075081-02*

Owner’s Manual

BCB-1000 Pedal Board Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the document(s)

where it will be available for immediate reference.

Main Specications

Connectors

INPUT Jack (1/4” phone type)

SEND Jack (1/4” phone type)

RETURN A/B Jack (1/4” phone type)

OUTPUT A/B Jack (1/4” phone type)

Dimensions 558 (W) x 354 (D) x 194 (H) mm

22 (W) x 14 (D) x 7-5/8 (H) inches

Pedal

installation

dimensions

496 (W) x 293 (D) x 94 (H) mm (front)

496 (W) x 293 (D) x 80 (H) mm (back)

19-1/2 (W) x 11-1/2 (D) x 3-3/4 (H) inches (front)

19-1/2 (W) x 11-1/2 (D) x 3-1/8 (H) inches (back)

Weight 6.7 kg (14 lbs 13 oz)

Accessories Owner’s Manual

• This document explains the specications of the product at the time that the document was issued. For

the latest information, refer to the Roland website.

Eect Unit Installation Examples

By using the slits in the plate to route the cables behind the plate, you can hide the cabling to get a clean layout.

* You can install a commercially available power supply under the plate.

* To secure the eect units, use commercially available hook-and-loop fasteners.

Removing the Plate

If you want to route cables behind the plate, your work will be easier if you remove the plate from the bottom case.

To remove the plate from the bottom case, turn the bottom case over and loosen the coin screws at the four corners.

* Take care that the plate does not fall when you loosen the coin screws.

* When attaching the plate to the bottom case, make sure that the cables you installed are not pinched between the bottom case and the

plate, and then tighten the coin screws.

Plate

Bottom Case

Coin screws

Loosen

Tighten

Before You Use the Case

Parts and functions of the top case

Top Handle

Use this to carry the case.

Pulling Handle

Use this to pull the case.

By pulling the handle out while pressing the

button, you can adjust the length.

Side Handle

Casters

Use these to pull the case.

* Note that malfunctions may occur if sand

or dust adheres to the casters, or if threads

wrap around them.

Attaching the top case

Before carrying the case, align the four fasteners of the top case with the bottom case, and press

the fasteners inward until you hear them click into place.

Connecting the Equipment

Simply connect the INPUT/OUTPUT jacks of the plate to your guitar and amp, and you’re ready to perform.

To connect the pedals, use the SEND/RETURN jacks located on the back of the plate.

1 INPUT jack

Connect your guitar.

2 OUTPUT A jack

Connect your guitar amp.

3 OUTPUT B jack

Connect your guitar amp.

Use these for stereo output, or if you want an output that

is separate from the OUTPUT A jack.

4 SEND jack

This outputs the signal that is input to the INPUT jack.

Connect this to the input of your eect unit.

5 RETURN A jack

Connect this to the output of your eect unit. The signal

is output to the OUTPUT A jack.

6 RETURN B jack

Connect this to the output of your eect unit. The signal

is output to the OUTPUT B jack.

12 3

4 5 6

USING THE UNIT SAFELY

WARNING

Do not disassemble or modify by yourself

Do not carry out anything unless you are instructed to

do so in the owner’s manual. Otherwise, you risk causing

malfunction.

Do not repair or replace parts by yourself

Be sure to contact your dealer, a Roland service center, or

an ocial Roland dealer.

For a list of Roland service centers and ocial Roland

dealers, refer to the Roland website.

Do not place in an unstable location

Otherwise, you risk injury as the result of the unit toppling

over or dropping down.

Be cautious to protect children from injury

Always make sure that an adult is on hand to provide

supervision and guidance when using the unit in places

where children are present, or when a child will be using

the unit.

Do not drop or subject to strong impact

Otherwise, you risk causing damage or malfunction.

CAUTION

Avoid climbing on top of the unit, or placing heavy objects on it

Otherwise, you risk injury as the result of the unit toppling

over or dropping down.

Take care so as not to get ngers pinched

When handling the following moving parts, take care

so as not to get ngers, toes, etc., pinched. Whenever a

child uses the unit, an adult should be on hand to provide

supervision and guidance.

• Case

• Handles

• Plate

Keep small items out of the reach of children

To prevent accidental ingestion of the parts listed below,

always keep them out of the reach of small children.

• Removable Parts

Coin screws

CAUTION

Take care not to injure your ngers, etc.

When handling the plate, take care that the edge of the

openings or components do not cut your ngers, etc.

Take care to avoid burns

The casters might be hot after the unit has been pulled.

Take care not to burn yourself.

Use the pulling Handle correctly

Do not lift the unit by the pulling Handle, or apply

excessive force to the pulling Handle. Doing so might cause

damage or malfunctions.

Do not use the casters inappropriately

Do not use the casters on stairsteps or when there are

dierences in level; use the handles of the unit instead.

Using the casters in an inappropriate situation might cause

damager or malfunction.

IMPORTANT NOTES

Placement

• Depending on the material and temperature of the surface on

which you place the unit, its rubber feet may discolor or mar

the surface.

Maintenance

• Never use benzine, thinners, alcohol or solvents of any kind, to

avoid the possibility of discoloration and/or deformation.

Additional Precautions

• When disposing of the packing carton or cushioning material

in which this unit was packed, you must observe the waste

disposal regulations that apply to your locality.

• When opening/closing the cover, please be careful not to get

your ngers pinched between the movable part and the unit.

In places where small children are present, make sure that an

adult provides supervision and guidance.

Intellectual Property Right

• Roland and BOSS are either registered trademarks or

trademarks of Roland Corporation in the United States and/

or other countries.

• Company names and product names appearing in this

document are registered trademarks or trademarks of their

respective owners.

For EU Countries

Roland Corporation

2036-1 Nakagawa, Hosoe-cho, Kita-ku, Hamamatsu, Shizuoka 431-1304, JAPAN

Roland Corporation

ENA 23 Zone 1 nr. 1620 Klaus-Michael Kuehnelaan 13, 2440 Geel, BELGIUM

Importer:

Manufacturer:

For EU Countries

Roland Corporation

2036-1 Nakagawa, Hosoe-cho, Kita-ku, Hamamatsu, Shizuoka 431-1304, JAPAN

Roland Europe Group Limited

Hive 2, 1530 Arlington Business Park, Theale, Reading, Berkshire. RG7 4SA United Kingdom

Importer:

Manufacturer:

For the U.K.

For details on the BCB-1000, refer to the BOSS website.

https://www.boss.info/global/products/bcb-1000/

For BOSS cables, refer to the BOSS website (Accessories).

https://www.boss.info/global/categories/accessories/boss_cables/

Used for instructions intended to alert the

user to the risk of injury or material

damage should the unit be used

improperly.

* Material damage refers to damage or

other adverse effects caused with

respect to the home and all its

furnishings, as well to domestic animals

or pets.

Used for instructions intended to alert the

user to the risk of death or severe injury

should the unit be used improperly.

The symbol alerts the user to things that must be

carried out. The specific thing that must be done is

indicated by the design contained within the circle. In the

case of the symbol at left, it means that the power-cord

plug must be unplugged from the outlet.

The symbol alerts the user to important instructions or

warnings.The specific meaning of the symbol is

determined by the design contained within the triangle. In

the case of the symbol at left, it is used for general

cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be

carried out (are forbidden). The specific thing that must

not be done is indicated by the design contained within

the circle. In the case of the symbol at left, it means that

the unit must never be disassembled.

About WARNING and CAUTION Notices About the Symbols

ALWAYS OBSERVE THE FOLLOWING

When you need repair service, access this URL and nd your nearest Roland

Service Center or authorized Roland distributor in your country.

https://roland.cm/service

Roland Service Centers and Distributors

Product specificaties

Merk:	Boss
Categorie:	Receiver
Model:	BCB-1000
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Gewicht:	6700 g
Breedte:	558 mm
Diepte:	354 mm
Hoogte:	194 mm
Gebruikershandleiding:	Ja
Pedaal-aansluiting:	Ja
Merkcompatibiliteit:	Boss
Gebruiksvriendelijk:	Ja
Type product:	Opbergtas
Uitgang van 6,35 mm (1/4-inch):	2
Ingang van 6,35 mm (1/4-inch):	2