Bosch F220-B6C Handleiding

Bosch Detector F220-B6C

Lees hieronder de 📖 handleiding in het Nederlandse voor Bosch F220-B6C (28 pagina's) in de categorie Detector. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/28

F220 Series Detectors with

F220-B6/C/E/R Bases

Installation Manual

en English manual

2en | Legal F220 Series Detectors with F220-B6/C/E/R Bases

4998138694 -04 | 2007.01 Installation Manual Bosch Security Systems, Inc.

1 Legal

1.1 Trademarks

CleanMe® is a registered trademark of GE Interlogix in the

United States and/or other countries.

Chamber Check® is a registered trademark of Bosch Security

Systems, Inc. in the United States.

Chambermaid™ is a trademark of Bosch Security Systems, Inc.

in the United States.

ENVI-RO-TECH™ is a trademark of Tech Spray L.P.

TECHSPRAY® is a registered trademark of Tech Spray L.P.

1.2 Required Maintenance and Testing

Keep the detector calibrated for proper operation. NFPA 72,

The National Fire Alarm Code, recommends performing

calibration tests at installation, then every other year.

Depending on local regulations, calibration testing might be

required more than once a year.

Perform functional testing yearly.

Test the calibration (to meet NFPA 72) using either the magnet

test or measuring the calibration with a calibrated product from

No Climb Products Ltd. Quickly determine the calibration by a

visual inspection of the detector’s LED (refer to Section 4.4

Flash Rate and Trouble Indication on page 22). These tests

confirm whether or not the detector is within its factory marked

calibration range.

At least once a year vacuum or wipe the external part of the

detector clean. Pay particular attention to the detector screens

in areas of heavy insect activity or dust. To clean the chamber,

NOTE! Notify all concerned parties before any

maintenance or testing of the fire alarm system and upon

completion of these activities.

F220 Series Detectors with F220-B6/C/E/R Bases General Information | en 3

Bosch Security Systems, Inc. Installation Manual 4998138694 -04 | 2007.01

use a can of clean, dry compressed air (such as TECHSPRAY

ENVI-RO-TECH Duster) which is available at office and alarm

supply stores. Shorten the plastic tube that comes with the

compressed air to about 2 in. (5 cm). Place the tube or needle

valve through the Chambermaid valve in the bottom of the

detector (refer to Figure 2.2 on page 7).

2 General Information

This document covers mounting, wiring, power requirements,

testing, and maintenance for the F220-B6, F220-B6C, F220-B6E,

and F220-B6R Detector Bases and the F220 Series Heat and

Photoelectric Smoke Detectors. Install them according to

NFPA 72.

For installation guidelines, refer to Installation Considerations

for Smoke and Fire Detectors (P/N: 26715).

2.1 F220-B6 Series Detector Bases

2.1.1 Compatible Control Panels

Two-wire:

NOTE! Do not paint the detectors. Paint or other foreign

matter covering the detector can prevent smoke

detection.

NOTE! For proper system installation, read and

understand NFPA-72 before installation.

NOTE! Bosch Security Systems, Inc. makes no claim

written, oral, or implied that the F220 Series Detectors

work with any two-wire control panels except those

specified in the Base Compatibility chart in Technical

Service Note (P/N: 4998148185).

Product specificaties

Merk:	Bosch
Categorie:	Detector
Model:	F220-B6C
Kleur van het product:	Wit
Breedte:	152 mm
Diepte:	152 mm
Hoogte:	23 mm
Montagewijze:	Opbouwmontage
Certificering:	UL, FM, CSFM, NYC-MEA, MSFM, HKFSD
Materiaal:	Kunststof
Aantal per verpakking:	1 stuk(s)
Ingangsspanning:	12/24 V
Koppelbaar:	Ja
Bedrijfstemperatuur (T-T):	0 - 38 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Back-upbatterij:	Nee
Ingebouwd relais:	Ja