Bosch 1775E Handleiding
Bosch
Haakse slijper
1775E
Lees hieronder de đź“– handleiding in het Nederlandse voor Bosch 1775E (32 pagina's) in de categorie Haakse slijper. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/32
Operating/Safety Instructions
Consignes de fonctionnement/sécurité
Instrucciones de funcionamiento
y seguridad
IMPORTANT: IMPORTANT : IMPORTANTE:
Read Before Using Lire avant usage Leer antes de usar
For English Parlez-vous français? ¿Habla español?
See page 2 Voir page 12 Ver página 22
Consumer Information
Renseignement des consommateurs
InformaciĂłn para el consumidor
Toll Free Number: Appel gratuit : Número de teléfono gratuito:
1-877-BOSCH99 (1-877-267-2499) http://www.boschtools.com
1775E
BM 3609929818 3/03 3/10/03 8:42 AM Page 1
Read and understand all instructions. Failure to follow all instructions
listed below, may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
-2-
Work Area
Keep your work area clean and well lit.
Cluttered benches and dark areas invite
accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power
tools create sparks which may ignite the
dust or fumes.
Keep by-standers, children, and visitors
away while operating a power tool.
Distractions can cause you to lose control.
Electrical Safety
Double Insulated tools are equipped with
a polarized plug (one blade is wider than
the other.) This plug will fit in a polarized
outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified
electrician to install a polarized outlet. Do
not change the plug in any way. Double
Insulation eliminates the need for the
three wire grounded power cord and
grounded power supply system. Before
plugging in the tool, be certain the outlet
voltage supplied is within the voltage marked
on the nameplate. Do not use “AC only”
rated tools with a DC power supply.
Avoid body contact with grounded
surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased
risk of electric shock if your body is
grounded. If operating the power tool in
damp locations is unavoidable, a Ground
Fault Circuit Interrupter must be used to
supply the power to your tool. Electrician’s
rubber gloves and footwear will further
enhance your personal safety.
Don't expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the
cord to carry the tools or pull the plug
from an outlet. Keep cord away from
heat, oil, sharp edges or moving parts.
Replace damaged cords immediately.
Damaged cords increase the risk of electric
shock.
When operating a power tool outside, use
an outdoor extension cord marked "W-A"
or "W." These cords are rated for outdoor
use and reduce the risk of electric shock.
Refer to “Recommended sizes of Extension
Cords” in the Accessory section of this
manual.
Personal Safety
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
Dress properly. Do not wear loose
clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away
from moving parts. Loose clothes, jewelry,
or long hair can be caught in moving parts.
Keep handles dry, clean and free from oil
and grease.
Avoid accidental starting. Be sure switch
is “OFF” before plugging in. Carrying tools
with your finger on the switch or plugging in
tools that have the switch “ON” invites
accidents.
Remove adjusting keys or wrenches
before turning the tool “ON”. A wrench or
a key that is left attached to a rotating part
of the tool may result in personal injury.
Do not overreach. Keep proper footing
and balance at all times. Proper footing
and balance enables better control of the
tool in unexpected situations.
Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must
be used for appropriate conditions.
!
WARNING
Power Tool Safety Rules
BM 3609929818 3/03 3/10/03 8:42 AM Page 2
-3-
Tuckpointer Safety Rules
Tool Use and Care
Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand
or against your body is unstable and may
lead to loss of control.
Do not force tool. Use the correct tool for
your application. The correct tool will do
the job better and safer at the rate for which
it is designed.
Do not use tool if switch does not turn it
“ON” or “OFF”. Any tool that cannot be
controlled with the switch is dangerous and
must be repaired.
Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally. Store
idle tools out of reach of children and
other untrained persons. Tools are
dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting
tools sharp and clean. Properly maintained
tools, with sharp cutting edges are less likely
to bind and are easier to control. Any
alteration or modification is a misuse and
may result in a dangerous condition.
Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tools
operation. If damaged, have the tool
serviced before using. Many accidents are
caused by poorly maintained tools. Develop
a periodic maintenance schedule for your
tool.
Use only accessories that are
recommended by the manufacturer for
your model. Accessories that may be
suitable for one tool, may become hazardous
when used on another tool.
Service
Tool service must be performed only by
qualified repair personnel. Service or
maintenance performed by unqualified
personnel could result in a risk of injury. For
example: internal wires may be misplaced or
pinched, safety guard return springs may be
improperly mounted.
When servicing a tool, use only identical
replacement parts. Follow instructions in
the Maintenance section of this manual.
Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk
of electric shock or injury. Certain cleaning
agent s such as gasoline, carbon
tetrachloride, ammonia, etc. may damage
plastic parts.
This machine is intended primarily for
tuckpointing applications and some small
abrasive masonry cut off applications. It
is not intended for metal or wood cutting.
Always use wheel guard system and
auxiliary handle with this tool. The guard
must always be securely attached to the
tool and positioned for maximum safety,
so the least amount of wheel is exposed
on the operators’ side of the tool. A guard
pr otects operator from broken wheel
fragments and swarf from grinding. The
auxiliary handle provides additional stability
and control in tuckpointing and cut off
applications.
Hold tool by insulated gripping surfaces
when performing an operation where the
abrasive wheels may contact hidden
wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of
the tool “live” and shock the operator.
Always use auxiliary handle for maximum
control over torque reaction or kick-back.
Operation of the tuckpointer without the side
handle could cause loss of control of the
tuckpointer, resulting in possible serious
personal injury.
Wear proper apparel while using an
abrasive tool. Use thick cushioned
gloves and wear ear protectors when
using the tool and limit exposure time by
taking frequent rest periods. Face shield
or at least safety goggles, dust mask,
leather gloves and shop apron capable of
stopping small wheel or workpiece
fragments. Prolonged exposure to high
BM 3609929818 3/03 3/10/03 8:42 AM Page 3
Product specificaties
| Merk: | Bosch |
| Categorie: | Haakse slijper |
| Model: | 1775E |
Heb je hulp nodig?
Als je hulp nodig hebt met Bosch 1775E stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Haakse slijper Bosch
1 November 2024
1 November 2024
13 Augustus 2022
27 Juli 2022
8 Augustus 2022
4 Augustus 2022
5 Augustus 2022
28 Juli 2022
13 Augustus 2022
4 Augustus 2022
Handleiding Haakse slijper
- Haakse slijper DeWalt
- Haakse slijper Batavia
- Haakse slijper Black Decker
- Haakse slijper Bruder Mannesmann
- Haakse slijper Ferm
- Haakse slijper Flex
- Haakse slijper Fuxtec
- Haakse slijper Gamma
- Haakse slijper Lux Tools
- Haakse slijper Max
- Haakse slijper Parkside
- Haakse slijper Scheppach
- Haakse slijper Skil
- Haakse slijper Stanley
- Haakse slijper Toledo
- Haakse slijper Topcraft
- Haakse slijper Trotec
Nieuwste handleidingen voor Haakse slijper
13 Oktober 2023
13 Oktober 2023
2 Augustus 2023
30 Mei 2023
20 December 2022
13 Maart 2023
28 Februari 2023
30 Maart 2023
8 Juli 2023
8 Juli 2023