Bogen BDT30A Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Bogen BDT30A (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Watts (70V)
1.8
3.7
7.5
15
30
*
*
Speaker Installation
Bi-Directional Reentrant
Horn Loudspeaker
Specifications subject to change without notice.
© 2000 Bogen Communications Inc. All rights reserved.
Part No. 54-584 C 04021 1-0
Speaker Assembly
The bi-directional speaker must be assembled prior to installation. See Figure on the back of this sheet for speaker assembly3
information. Make sure to place the washer/seals where indicated and hand tighten the various components - do not use pliers
or similar tools.
STEP -1For easier installation, remove the flange (base) from the speak-
er by unscrewing the wing nut while at the same time pressing inwardly on
the wing nut. Place the flange flush with the mounting surface and mark the
location of the three holes with either a marker or punch. It is important
that the three holes be exactly aligned with the flange, otherwise you might
stress the base or make the connection unsteady (see Figure 1).
NOTE: Speaker may also be strap-mounted through the slot in flange (base)
using standard /2-inch industrial strapping (not included).1
STEP 2 - After mounting the flange, reattach the speaker to the flange and
aim the speaker for the desired coverage. A 45odownward angle is rec-
ommended, but this may vary depending upon speaker layout. Unless oth-
erwise indicated, do not aim speakers directly at each other or poor paging
intelligibility may occur.
STEP 3 - Remove the plastic cover to make the electrical connection and
set the tap set control (see Figure 2). Connect speaker wire shield to the
ground (GND) terminal of the amplifier’s output. Carry the ground through
all speaker cables by tying the shields of the speaker cables together in a
“daisy chain” fashion. Do not connect the shield to the speaker itself.
The shield is only connected at the amplifier end and simply floats.
Connect wires as listed below:
Amplifier Outputs Speaker Connections
70V/25V Terminal 1
COM Terminal 2
NOTE: The speaker will also work perfectly well with these connections reversed.
However, reduced low frequency response may result.
STEP 4 - Adjust the tap set control to the desired setting. See table at right
for tap settings. Replace the plastic protective cover back over the exposed
area.
Frequency Response: 225 Hz to 4 kHz1
Dimensions: 161/2" W x 93/4" H (4 .9 x 24.8 cm)1
Shipping Weight: 9 lb.
Finish: Textured Mocha Enamel
Sound Pressure Level: 1 1 2 dB @ four feet on axis with 30-watt input
at 1000 Hz each horn
Figure 2
ELECTRICAL
CONNECTION
TAP SET
CONTROL
Page 1 of 2
Figure 1: Mounting Speaker Base
Position
1
2
3
4
5
6
7
Watts (25V)
.25
.5
1
1.8
3.7
7.5
15
*Forbidden switch settings (see text)
CAUTION
Switch settings marked with an asterisk (*) must not be
used. Failure to comply with these restrictions may cause
damage to components and will void the warranty.
8* *
BDT30A
1-7/8" DIA
PAPER GASKET
1-5/16" DIA
GREY FIBER WASHER
1-7/8" DIA
STEEL WASHER
1-7/8" DIA
PAPER GASKET
THUMB
SCREW
1-7/8" DIA
PAPER GASKET
1-5/16" DIA
BLACK RUBBER WASHER
1-5/16" DIA
GREY FIBER WASHER
AFTER ASSEMBLY, ALIGN LOGO
AND TIGHTEN SCREW
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
AFTER ASSEMBLY,
ALIGN LOGO AND
TIGHTEN SCREWS
Figure 3: Speaker Assembly
Figure 4: Assembled Speaker
Page 2 of 2
NOTE: Extra gaskets may be included in hardware pack.
50 Spring Street, Ramsey, NJ 07446
Tel. 20 -934-8500, Fax: 20 -934-98321 1
Web Site: www.bogen.com


Product specificaties

Merk: Bogen
Categorie: Niet gecategoriseerd
Model: BDT30A
Gewicht: 3175 g
Breedte: 9.625 "
Hoogte: 9.625 "
Materiaal behuizing: Metaal
Stroomvoorziening: 70V/25V
Bluetooth: Nee
Connectiviteitstechnologie: Bedraad
Type stroombron: AC
Gemiddeld vermogen: 30 W
Equalizer-instellingen: Nee
Aanbevolen gebruik: Universeel
Audio-uitgangskanalen: 1.0 kanalen
Speaker plaatsing: Tabletop/bookshelf, Wall-mountable
Aantal drivers: 2
Frequentiebereik: 225 - 14000 Hz
Gevoeligheid: 121 dB
Diepte (imperiaal): 12.125 "
Wifi: Nee

Heb je hulp nodig?

Als je hulp nodig hebt met Bogen BDT30A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Bogen

Bogen

Bogen CK10B Handleiding

10 Maart 2025
Bogen

Bogen TBSF Handleiding

10 Maart 2025
Bogen

Bogen TB8 Handleiding

10 Maart 2025
Bogen

Bogen RE84 Handleiding

10 Maart 2025
Bogen

Bogen CK10 Handleiding

10 Maart 2025
Bogen

Bogen BC1 Handleiding

10 Maart 2025
Bogen

Bogen SPS2466 Handleiding

28 Februari 2025
Bogen

Bogen SPS2425 Handleiding

28 Februari 2025
Bogen

Bogen WB1EZ Handleiding

28 Februari 2025
Bogen

Bogen SM4T Handleiding

28 Februari 2025

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd